[V4 1/2] phy: ralink-usb: add driver for Mediatek/Ralink

[James Hogan]

On 9 August 2017 10:35:39 BST, Harvey Hunt <harvey.hunt at imgtec.com> wrote:
>From: John Crispin <john at phrozen.org>
>
>Add a driver to setup the USB phy on Mediatek/Ralink SoCs.
>The driver is trivial and only sets up power and host mode.
>
>Signed-off-by: John Crispin <john at phrozen.org>
>Signed-off-by: Harvey Hunt <harvey.hunt at imgtec.com>
>Cc: linux-kernel at vger.kernel.org
>Cc: linux-mediatek at lists.infradead.org
>---
>Changes in V4
>* Remove Allwinner from comment
>* Depend on COMPILE_TEST
>
>Changes in V3
>* Separate DT bindings
>* Update Kconfig text
>* Modify John's email address
>* Rebase onto v4.13-rc3
>
>Changes in V2
>* remove refcounting
>* drop empty functions
>* dont use static globals
>* use explicit compatible strings
>
> drivers/phy/Kconfig          |   8 ++
> drivers/phy/Makefile         |   1 +
>drivers/phy/phy-ralink-usb.c | 173
>+++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 182 insertions(+)
> create mode 100644 drivers/phy/phy-ralink-usb.c
>
>diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>index c1807d4..8fb5260 100644
>--- a/drivers/phy/Kconfig
>+++ b/drivers/phy/Kconfig
>@@ -41,6 +41,14 @@ config PHY_PISTACHIO_USB
> 	help
> 	  Enable this to support the USB2.0 PHY on the IMG Pistachio SoC.
> 
>+config PHY_RALINK_USB
>+	tristate "Ralink USB PHY driver"
>+	select GENERIC_PHY
>+	depends on RALINK || COMPILE_TEST

given that the driver includes a asm/mach-ralink header, the COMPILE_TEST bit may break x86 allmodconfig?

maybe the header should be moved out of arch/mips or it should depend on MIPS only (so a mips allmodconfig catches it, but cant be enabled on x86 even with COMPILE_TEST=y)

cheers
James

>+	help
>+	  This option enables support for the Ralink USB PHY found inside
>+	  RT3352, MT7620, MT7628 and MT7688.
>+
> config PHY_XGENE
> 	tristate "APM X-Gene 15Gbps PHY support"
> 	depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
>diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>index f252201..60ed30b 100644
>--- a/drivers/phy/Makefile
>+++ b/drivers/phy/Makefile
>@@ -7,6 +7,7 @@ obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+=
>phy-lpc18xx-usb-otg.o
> obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
> obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
> obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
>+obj-$(CONFIG_PHY_RALINK_USB)		+= phy-ralink-usb.o
> 
> obj-$(CONFIG_ARCH_SUNXI)		+= allwinner/
> obj-$(CONFIG_ARCH_MESON)		+= amlogic/
>diff --git a/drivers/phy/phy-ralink-usb.c
>b/drivers/phy/phy-ralink-usb.c
>new file mode 100644
>index 0000000..14a254a
>--- /dev/null
>+++ b/drivers/phy/phy-ralink-usb.c
>@@ -0,0 +1,173 @@
>+/*
>+ * Copyright (C) 2016 John Crispin <john at phrozen.org>
>+ *
>+ * Based on code from
>+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
>+ *
>+ * This program is free software; you can redistribute it and/or
>modify
>+ * it under the terms of the GNU General Public License as published
>by
>+ * the Free Software Foundation; either version 2 of the License, or
>+ * (at your option) any later version.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>+ * GNU General Public License for more details.
>+ */
>+
>+#include <linux/delay.h>
>+#include <linux/err.h>
>+#include <linux/io.h>
>+#include <linux/kernel.h>
>+#include <linux/module.h>
>+#include <linux/mutex.h>
>+#include <linux/phy/phy.h>
>+#include <linux/platform_device.h>
>+#include <linux/reset.h>
>+#include <linux/of_platform.h>
>+
>+#include <asm/mach-ralink/ralink_regs.h>
>+
>+#define RT_SYSC_REG_SYSCFG1		0x014
>+#define RT_SYSC_REG_CLKCFG1		0x030
>+#define RT_SYSC_REG_USB_PHY_CFG		0x05c
>+
>+#define RT_RSTCTRL_UDEV			BIT(25)
>+#define RT_RSTCTRL_UHST			BIT(22)
>+#define RT_SYSCFG1_USB0_HOST_MODE	BIT(10)
>+
>+#define MT7620_CLKCFG1_UPHY0_CLK_EN	BIT(25)
>+#define MT7620_CLKCFG1_UPHY1_CLK_EN	BIT(22)
>+#define RT_CLKCFG1_UPHY1_CLK_EN		BIT(20)
>+#define RT_CLKCFG1_UPHY0_CLK_EN		BIT(18)
>+
>+#define USB_PHY_UTMI_8B60M		BIT(1)
>+#define UDEV_WAKEUP			BIT(0)
>+
>+struct ralink_usb_phy {
>+	struct reset_control	*rstdev;
>+	struct reset_control	*rsthost;
>+	u32			clk;
>+	struct phy		*phy;
>+};
>+
>+static int ralink_usb_phy_power_on(struct phy *_phy)
>+{
>+	struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
>+	u32 t;
>+
>+	/* enable the phy */
>+	rt_sysc_m32(0, phy->clk, RT_SYSC_REG_CLKCFG1);
>+
>+	/* setup host mode */
>+	rt_sysc_m32(0, RT_SYSCFG1_USB0_HOST_MODE, RT_SYSC_REG_SYSCFG1);
>+
>+	/* deassert the reset lines */
>+	reset_control_deassert(phy->rsthost);
>+	reset_control_deassert(phy->rstdev);
>+
>+	/*
>+	 * The SDK kernel had a delay of 100ms. however on device
>+	 * testing showed that 10ms is enough
>+	 */
>+	mdelay(10);
>+
>+	/* print some status info */
>+	t = rt_sysc_r32(RT_SYSC_REG_USB_PHY_CFG);
>+	dev_info(&phy->phy->dev, "remote usb device wakeup %s\n",
>+		(t & UDEV_WAKEUP) ? ("enabled") : ("disabled"));
>+	if (t & USB_PHY_UTMI_8B60M)
>+		dev_info(&phy->phy->dev, "UTMI 8bit 60MHz\n");
>+	else
>+		dev_info(&phy->phy->dev, "UTMI 16bit 30MHz\n");
>+
>+	return 0;
>+}
>+
>+static int ralink_usb_phy_power_off(struct phy *_phy)
>+{
>+	struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
>+
>+	/* disable the phy */
>+	rt_sysc_m32(phy->clk, 0, RT_SYSC_REG_CLKCFG1);
>+
>+	/* assert the reset lines */
>+	reset_control_assert(phy->rstdev);
>+	reset_control_assert(phy->rsthost);
>+
>+	return 0;
>+}
>+
>+static struct phy_ops ralink_usb_phy_ops = {
>+	.power_on	= ralink_usb_phy_power_on,
>+	.power_off	= ralink_usb_phy_power_off,
>+	.owner		= THIS_MODULE,
>+};
>+
>+static const struct of_device_id ralink_usb_phy_of_match[] = {
>+	{
>+		.compatible = "ralink,rt3352-usbphy",
>+		.data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN |
>+				  RT_CLKCFG1_UPHY0_CLK_EN)
>+	},
>+	{
>+		.compatible = "mediatek,mt7620-usbphy",
>+		.data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
>+				  MT7620_CLKCFG1_UPHY0_CLK_EN) },
>+	{ },
>+};
>+MODULE_DEVICE_TABLE(of, ralink_usb_phy_of_match);
>+
>+static int ralink_usb_phy_probe(struct platform_device *pdev)
>+{
>+	struct device *dev = &pdev->dev;
>+	struct phy_provider *phy_provider;
>+	const struct of_device_id *match;
>+	struct ralink_usb_phy *phy;
>+
>+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>+	if (!phy)
>+		return -ENOMEM;
>+
>+	match = of_match_device(ralink_usb_phy_of_match, &pdev->dev);
>+	if (!match)
>+		return -ENODEV;
>+
>+	phy->clk = (int) match->data;
>+
>+	phy->rsthost = devm_reset_control_get(&pdev->dev, "host");
>+	if (IS_ERR(phy->rsthost)) {
>+		dev_err(dev, "host reset is missing\n");
>+		return PTR_ERR(phy->rsthost);
>+	}
>+
>+	phy->rstdev = devm_reset_control_get(&pdev->dev, "device");
>+	if (IS_ERR(phy->rstdev)) {
>+		dev_err(dev, "device reset is missing\n");
>+		return PTR_ERR(phy->rstdev);
>+	}
>+
>+	phy->phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops);
>+	if (IS_ERR(phy->phy)) {
>+		dev_err(dev, "failed to create PHY\n");
>+		return PTR_ERR(phy->phy);
>+	}
>+	phy_set_drvdata(phy->phy, phy);
>+
>+	phy_provider = devm_of_phy_provider_register(dev,
>of_phy_simple_xlate);
>+
>+	return PTR_ERR_OR_ZERO(phy_provider);
>+}
>+
>+static struct platform_driver ralink_usb_phy_driver = {
>+	.probe	= ralink_usb_phy_probe,
>+	.driver = {
>+		.of_match_table	= ralink_usb_phy_of_match,
>+		.name  = "ralink-usb-phy",
>+	}
>+};
>+module_platform_driver(ralink_usb_phy_driver);
>+
>+MODULE_DESCRIPTION("Ralink USB phy driver");
>+MODULE_AUTHOR("John Crispin <john at phrozen.org>");
>+MODULE_LICENSE("GPL v2");


--
James Hogan