[PATCH v2 2/4] thermal: mediatek: add Mediatek thermal driver for mt2712

[Zhang Rui]

On Tue, 2017-08-01 at 15:28 +0800, Louis Yu wrote:
> This patch adds support for mt2712 chip to mtk_thermal,
> and integrate mt2712 into the same mediatek thermal driver.
> MT2712 has only 1 bank and 4 sensors.
> 
> Signed-off-by: Louis Yu <louis.yu at mediatek.com>
> ---
>  drivers/thermal/mtk_thermal.c | 70
> ++++++++++++++++++++++++++++++++++++++++---
>  1 file changed, 66 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/thermal/mtk_thermal.c
> b/drivers/thermal/mtk_thermal.c
> index 7737f14..e35d28d 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -3,6 +3,7 @@
>   * Author: Hanyi Wu <hanyi.wu at mediatek.com>
>   *         Sascha Hauer <s.hauer at pengutronix.de>
>   *         Dawei Chien <dawei.chien at mediatek.com>
> + *         Louis Yu <louis.yu at mediatek.com>

I need the feedback from the previous authors for the changes in all
this patch set.

>   *
>   * This program is free software; you can redistribute it and/or
> modify
>   * it under the terms of the GNU General Public License version 2 as
> @@ -111,9 +112,10 @@
>  
>  /*
>   * Layout of the fuses providing the calibration data
> - * These macros could be used for both MT8173 and MT2701.
> + * These macros could be used for both MT8173, MT2701, and MT2712.
>   * MT8173 has five sensors and need five VTS calibration data,
> - * and MT2701 has three sensors and need three VTS calibration data.
> + * and MT2701 has three sensors and need three VTS calibration data,
> + * and MT2712 has four sensors and need four VTS calibration data.
>   */

why bother change these comments again in patch 3/4?

thanks,
rui
>  #define MT8173_CALIB_BUF0_VALID		BIT(0)
>  #define MT8173_CALIB_BUF1_ADC_GE(x)	(((x) >> 22) & 0x3ff)
> @@ -136,11 +138,26 @@
>  /* The total number of temperature sensors in the MT2701 */
>  #define MT2701_NUM_SENSORS	3
>  
> -#define THERMAL_NAME    "mtk-thermal"
> -
>  /* The number of sensing points per bank */
>  #define MT2701_NUM_SENSORS_PER_ZONE	3
>  
> +/* MT2712 thermal sensors */
> +#define MT2712_TS1	0
> +#define MT2712_TS2	1
> +#define MT2712_TS3	2
> +#define MT2712_TS4	3
> +
> +/* AUXADC channel 11 is used for the temperature sensors */
> +#define MT2712_TEMP_AUXADC_CHANNEL	11
> +
> +/* The total number of temperature sensors in the MT2712 */
> +#define MT2712_NUM_SENSORS	4
> +
> +/* The number of sensing points per bank */
> +#define MT2712_NUM_SENSORS_PER_ZONE	4
> +
> +#define THERMAL_NAME    "mtk-thermal"
> +
>  struct mtk_thermal;
>  
>  struct thermal_bank_cfg {
> @@ -215,6 +232,21 @@ struct mtk_thermal {
>  
>  static const int mt2701_mux_values[MT2701_NUM_SENSORS] = { 0, 1, 16
> };
>  
> +/* MT2712 thermal sensor data */
> +static const int mt2712_bank_data[MT2712_NUM_SENSORS] = {
> +	MT2712_TS1, MT2712_TS2, MT2712_TS3, MT2712_TS4
> +};
> +
> +static const int mt2712_msr[MT2712_NUM_SENSORS_PER_ZONE] = {
> +	TEMP_MSR0, TEMP_MSR1, TEMP_MSR2, TEMP_MSR3
> +};
> +
> +static const int mt2712_adcpnp[MT2712_NUM_SENSORS_PER_ZONE] = {
> +	TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2, TEMP_ADCPNP3
> +};
> +
> +static const int mt2712_mux_values[MT2712_NUM_SENSORS] = { 0, 1, 2,
> 3 };
> +
>  /**
>   * The MT8173 thermal controller has four banks. Each bank can read
> up to
>   * four temperature sensors simultaneously. The MT8173 has a total
> of 5
> @@ -278,6 +310,31 @@ struct mtk_thermal {
>  };
>  
>  /**
> + * The MT2712 thermal controller has one bank, which can read up to
> + * four temperature sensors simultaneously. The MT2712 has a total
> of 4
> + * temperature sensors.
> + *
> + * The thermal core only gets the maximum temperature of this one
> bank,
> + * so the bank concept wouldn't be necessary here. However, the SVS
> (Smart
> + * Voltage Scaling) unit makes its decisions based on the same bank
> + * data.
> + */
> +static const struct mtk_thermal_data mt2712_thermal_data = {
> +	.auxadc_channel = MT2712_TEMP_AUXADC_CHANNEL,
> +	.num_banks = 1,
> +	.num_sensors = MT2712_NUM_SENSORS,
> +	.bank_data = {
> +		{
> +			.num_sensors = 4,
> +			.sensors = mt2712_bank_data,
> +		},
> +	},
> +	.msr = mt2712_msr,
> +	.adcpnp = mt2712_adcpnp,
> +	.sensor_mux_values = mt2712_mux_values,
> +};
> +
> +/**
>   * raw_to_mcelsius - convert a raw ADC value to mcelsius
>   * @mt:		The thermal controller
>   * @raw:	raw ADC value
> @@ -571,6 +628,10 @@ static int
> mtk_thermal_get_calibration_data(struct device *dev,
>  	{
>  		.compatible = "mediatek,mt2701-thermal",
>  		.data = (void *)&mt2701_thermal_data,
> +	},
> +	{
> +		.compatible = "mediatek,mt2712-thermal",
> +		.data = (void *)&mt2712_thermal_data,
>  	}, {
>  	},
>  };
> @@ -705,6 +766,7 @@ static int mtk_thermal_remove(struct
> platform_device *pdev)
>  
>  module_platform_driver(mtk_thermal_driver);
>  
> +MODULE_AUTHOR("Louis Yu <louis.yu at mediatek.com>");
>  MODULE_AUTHOR("Dawei Chien <dawei.chien at mediatek.com>");
>  MODULE_AUTHOR("Sascha Hauer <s.hauer at pengutronix.de>");
>  MODULE_AUTHOR("Hanyi Wu <hanyi.wu at mediatek.com>");