[PATCH v2 2/2] dt-bindings: ata: add DT bindings for MediaTek SATA controller

[Ryder Lee]

Add DT bindings for the onboard SATA controller present on the MediaTek
SoCs.

Signed-off-by: Ryder Lee <ryder.lee at mediatek.com>
---
 Documentation/devicetree/bindings/ata/ahci-mtk.txt | 50 ++++++++++++++++++++++
 1 file changed, 50 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ata/ahci-mtk.txt

diff --git a/Documentation/devicetree/bindings/ata/ahci-mtk.txt b/Documentation/devicetree/bindings/ata/ahci-mtk.txt
new file mode 100644
index 0000000..ed04dfc
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/ahci-mtk.txt
@@ -0,0 +1,50 @@
+MediaTek Seria ATA controller
+
+Required properties:
+ - compatible	   : Must be "mediatek,ahci".
+ - reg		   : Physical base addresses and length of register sets.
+ - interrupts	   : Interrupt associated with the SATA device.
+ - interrupt-names : Associated name must be: "hostc".
+ - clocks	   : A list of phandle and clock specifier pairs, one for each
+		     entry in clock-names.
+ - clock-names	   : Associated names must be: "ahb", "axi", "asic", "rbc", "pm".
+ - phys		   : A phandle and PHY specifier pair for the PHY port.
+ - phy-names	   : Associated name must be: "sata-phy".
+ - ports-implemented : Mask that indicates which ports that the HBA supports
+		       are available for software to use. Useful if PORTS_IMPL
+		       is not programmed by the BIOS, which is true with some
+		       embedded SOC's.
+
+Optional properties:
+ - power-domains   : A phandle and power domain specifier pair to the power
+		     domain which is responsible for collapsing and restoring
+		     power to the peripheral.
+ - resets	   : Must contain an entry for each entry in reset-names.
+		     See ../reset/reset.txt for details.
+ - reset-names	   : Associated names must be: "axi", "sw", "reg".
+ - mediatek,phy-mode : A phandle to the system controller, used to enable
+		       SATA function.
+
+Example:
+
+	sata: sata at 1a200000 {
+		compatible = "mediatek,ahci";
+		reg = <0 0x1a200000 0 0x1100>;
+		interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hostc";
+		clocks = <&pciesys CLK_SATA_AHB_EN>,
+			 <&pciesys CLK_SATA_AXI_EN>,
+			 <&pciesys CLK_SATA_ASIC_EN>,
+			 <&pciesys CLK_SATA_RBC_EN>,
+			 <&pciesys CLK_SATA_PM_EN>;
+		clock-names = "ahb", "axi", "asic", "rbc", "pm";
+		phys = <&u3port1 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+		resets = <&pciesys MT7622_SATA_AXI_BUS_RST>,
+			 <&pciesys MT7622_SATA_PHY_SW_RST>,
+			 <&pciesys MT7622_SATA_PHY_REG_RST>;
+		reset-names = "axi", "sw", "reg";
+		mediatek,phy-mode = <&pciesys>;
+	};
-- 
1.9.1