[PATCH net-next 3/3] net: ethernet: mediatek: add the dts property to set if TRGMII supported on GMAC0

[Andrew Lunn]

On Wed, Sep 21, 2016 at 02:16:30PM +0800, Sean Wang wrote:
> Date: Tue, 20 Sep 2016 21:37:58 +0200, Andrew Lunn <andrew at lunn.ch> wrote:
> >On Tue, Sep 20, 2016 at 03:59:20PM +0800, sean.wang at mediatek.com wrote:
> >> From: Sean Wang <sean.wang at mediatek.com>
> >>
> >> Add the dts property for the capability if TRGMII supported on GAMC0
> >>
> >> Signed-off-by: Sean Wang <sean.wang at mediatek.com>
> >> ---
> >>  Documentation/devicetree/bindings/net/mediatek-net.txt | 5 ++++-
> >>  1 file changed, 4 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt
> >> index 6103e55..32f79d8 100644
> >> --- a/Documentation/devicetree/bindings/net/mediatek-net.txt
> >> +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt
> >> @@ -31,7 +31,10 @@ Optional properties:
> >>  Required properties:
> >>  - compatible: Should be "mediatek,eth-mac"
> >>  - reg: The number of the MAC
> >> -- phy-handle: see ethernet.txt file in the same directory.
> >> +- phy-handle: see ethernet.txt file in the same directory and
> >> +     the additional phy-mode "tgrmii" is provided in order to connect
> >> +     with the internal switch MT7530 which is only applicable when reg
> >> +     is equal to 0.
> >
> >Humm. How is the switch connected? Is it on the MDIO bus?
> 
> the switch is connected to MDIO bus
> 
> >If it is on the mdio bus, the binding is going to look something like:
> >
> >eth: ethernet at 1b100000 {
> >        compatible = "mediatek,mt7623-eth";
> >        reg = <0 0x1b100000 0 0x20000>;
> >        clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
> >                 <&ethsys CLK_ETHSYS_ESW>,
> >                 <&ethsys CLK_ETHSYS_GP2>,
> >                 <&ethsys CLK_ETHSYS_GP1>;
> >        clock-names = "ethif", "esw", "gp2", "gp1";
> >        interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW
> >                      GIC_SPI 199 IRQ_TYPE_LEVEL_LOW
> >                      GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
> >        power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
> >        resets = <&ethsys MT2701_ETHSYS_ETH_RST>;
> >        reset-names = "eth";
> >        mediatek,ethsys = <&ethsys>;
> >        mediatek,pctl = <&syscfg_pctl_a>;
> >        #address-cells = <1>;
> >        #size-cells = <0>;
> >
> >        gmac1: mac at 0 {
> >                compatible = "mediatek,eth-mac";
> >                reg = <0>;
> >        };
> >
> >        gmac2: mac at 1 {
> >                compatible = "mediatek,eth-mac";
> >                reg = <1>;
> >        };
> >
> >        mdio-bus {
> >               reg = <1>;
> >               #address-cells = <1>;
> >               #size-cells = <0>;
> >
> >               switch0: switch0 at 0 {
> >                       compatible = "marvell,mv88e6085";
> >                       #address-cells = <1>;
> >                       #size-cells = <0>;
> >                       reg = <0>;
> >                       dsa,member = <0 0>;
> >
> >                       ports {
> >                               #address-cells = <1>;
> >                               #size-cells = <0>;
> >                               port at 0 {
> >                                       reg = <0>;
> >                                       label = "lan0";
> >...
> >...
> >In this case the switch is an MDIO device, not an PHY. It will not
> >have an phy-mode. It cannot have a phy mode, it is not a PHY.
> >
> >Or am i missing something here?
> >
> >Thanks
> >
> 
> 1)
> 
> The switch driver is not supported for DSA so far yet 
> but DSA is good thing and I will try make it happen
> in the near future.

O.K. But if i understand correctly, the TRGMII is so you can use the
switch. So it needs to work when you have DSA.
 
> And another question about DSA, that is
> if I use DSA for switch, how to know the relationship
> between MAC and DSA ? such like I could know relationship 
> between MAC and PHY by phy-handle.

It will look like what i stated above. But i missed the cpu node in
the ports, which is what you are asking about. There will also be a
node like:

                            port at 6 {
                                     reg = <6>;
                                     label = "cpu";
                                     ethernet = <&gmac1>;
                             };

And this is how you couple the MAC to DSA.

> The cause I ask is becasue I think it's good if the topology
> about MAC/PHYs/Switch is known just by dts files.
> 
> 2)
> 
> The phy-mode I mention is for fixed-link. For current MAC driver, 
> it just uses fixed phy to adapt into the part of switch, so the 
> device tree looks something like the below. 
> 
> &eth {
>         status = "okay";
>         gmac0: mac at 0 {
>                 compatible = "mediatek,eth-mac";
>                 reg = <0>;
>                 phy-mode = "trgmii";
>                 fixed-link {
>                         speed = <1000>;
>                         full-duplex;
>                         pause;
>                 };
>         };
> 
>         gmac1: mac at 1 {
>                 compatible = "mediatek,eth-mac";
>                 reg = <1>;
>                 phy-handle = <&phy5>;
>         };


static int mtk_phy_connect(struct mtk_mac *mac)
{
        struct mtk_eth *eth = mac->hw;
        struct device_node *np;
        u32 val;

        np = of_parse_phandle(mac->of_node, "phy-handle", 0);
        if (!np && of_phy_is_fixed_link(mac->of_node))
                if (!of_phy_register_fixed_link(mac->of_node))
                        np = of_node_get(mac->of_node);
	...
        ...
        mtk_phy_connect_node(eth, mac, np);


So in the case of a fixed-phy, you do look in the MAC node, and when
there is a phy-handle, you look in the PHY node.

So this does work....

   Andrew