[PATCH v4 2/2] mtd: mediatek: driver for MTK Smart Device Gen1 NAND

Boris Brezillon boris.brezillon at free-electrons.com
Tue May 10 07:55:17 PDT 2016


On Tue, 10 May 2016 10:37:32 -0400
Jorge Ramirez <jorge.ramirez-ortiz at linaro.org> wrote:

> On 05/10/2016 08:13 AM, Boris Brezillon wrote:
> >> +#define ECC_IDLE_REG(x)		((x) == ECC_ENC ? ECC_ENCIDLE : ECC_DECIDLE)  
> >> >+#define ECC_IDLE_MASK(x)	((x) == ECC_ENC ? ENC_IDLE : DEC_IDLE)  
> > No need for this macro, it's always bit0, so just define an ECC_IDLE
> > macro and use it for both decoder and encoder.  
> 
> this was only done for consistency to help people reading the code (same 
> for codec_enable, codec_disable).
> I suppose I could remove macros and just write 0 and 1 to the registers 
> if you prefer that.

No.

> 
> >
> > There seems to be some kind of pattern in your ENC/DEC registers.
> > ENC registers start at 0 and DEC ones at 0x100.
> > CNF register is always at 0x4 + mode/dir_offset (ie 0x100 for DEC and
> > 0x0 for ENC), ...
> > Maybe you should define common macros for those registers, and choose
> > the base offset depending on the mode you're operating in (encoding or
> > decoding).  
> 
> Not sure if you are familiar with George Lakoff and his book "Don't 
> Think Of An Elephant! Know Your Values And Frame The Debate" but the key 
> message is not to engage in a discussion when you disagree with the 
> terms used by your counterpart since you wont be able to frame the 
> argument (the book is actually very interesting if politics and and the 
> political debate is something that interest you)
> 
> I explicitly chose not to talk about modes, instead I chose the engine 
> driver to talk about the codecs it controls; for me mode is a higher 
> level concept that I didn't have a need for since in this case the mode 
> is a 1-1 relationship to the codec. So when you tell me about the mode 
> the engine is operating in I'd rather say the codec that the ecc engine 
> is accessing. I hope it makes sense.

I'm not arguing about the use of codec, but IMO codec is just
representing a device that is capable of encoding/decoding stuff, it
does not represent in which mode you want to use this device.

> 
> if you want to talk about modes instead of the encoders and decoders 
> that is fine since you are the maintainer.

No, the terms encoders/decoders are fine, I was just suggesting to
share some of the definitions between the encoder and decoder parts.

> I can rewrite the relevant parts of the driver but I honestly see no value.

No that's fine.

> 
> why did I wrote these macros? just for readability since they are simple 
> conditionals.

Again, I'm not arguing against the definition of helper macros, just
suggesting another way to do it to avoid register offset duplication.

> So coming back to your second question, I not sure why I would use a 
> base offset when I already have the map. I wouldn't.

Anyway, let's keep it like this.

> 
> >  
> >> >+#define ECC_IRQ_REG(x)		((x) == ECC_ENC ? ECC_ENCIRQ_EN : ECC_DECIRQ_EN)
> >> >+#define ECC_IRQ_EN(x)		((x) == ECC_ENC ? ENC_IRQEN : DEC_IRQEN)
> >> >+#define ECC_CTL_REG(x)		((x) == ECC_ENC ? ECC_ENCCON : ECC_DECCON)
> >> >+#define ECC_CODEC_ENABLE(x)	((x) == ECC_ENC ? ENC_EN : DEC_EN)
> >> >+#define ECC_CODEC_DISABLE(x)	((x) == ECC_ENC ? ENC_DE : DEC_DE)  
> 
> 



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com



More information about the Linux-mediatek mailing list