[PATCH] usb: xhci-mtk: fixup mouse wakeup failure during system suspend

[Felipe Balbi]

Hi,

chunfeng yun <chunfeng.yun at mediatek.com> writes:
>> chunfeng yun <chunfeng.yun at mediatek.com> writes:
>> > On Tue, 2016-05-03 at 12:33 +0300, Felipe Balbi wrote:
>> >> Hi,
>> >> 
>> >> chunfeng yun <chunfeng.yun at mediatek.com> writes:
>> >> >> chunfeng yun <chunfeng.yun at mediatek.com> writes:
>> >> >> > On Thu, 2016-04-21 at 10:04 +0800, Chunfeng Yun wrote:
>> >> >> >> Click mouse after xhci suspend completion but before system suspend
>> >> >> >> completion, system will not be waken up by mouse if the duration of
>> >> >> >> them is larger than 20ms which is the device UFP's resume signaling
>> >> >> 
>> >> >> what is "them" here ? The duration of what is longer than 20ms ?
>> >> > They are "xhci suspend completion" and "system suspend completion";
>> >> >
>> >> > It's time duration
>> >> 
>> >> okay. So if xhci suspend takes longer than 20ms your SPM doesn't see a
>> >> wakeup ?
>> > It is not the time of xhci suspend consumed, but is the time of duration
>> > from xhci suspend completion to system suspend completion(after BOOT-CPU
>> > is turned off, SPM will be enabled to receive wakeup event)
>> 
>> Okay, so SPM will be the entity actually handling wakeups, right ? I'm
>> assuming something like this happens:
>> 
>> echo mem > /sys/power/state
>>  /* start suspending devices */
>>   xhci_suspend()
>>  /* all devices suspended */
>>  enable_spm()
>> 
>> so, if a mouse button is pressed after xhci_suspend() returns but before
>> enable_spm() runs, then we're gonna miss that event, am I right ?
> Yes, you are right.
>> 
>> I can't think of any way to sort this out. Let's ask on linux-pm (I've
>> added linux-pm to Cc list)
> Thanks
>> 
>> >> >> >> lasted. Another reason is that the SPM is not enabled before system
>> >> >> 
>> >> >> what's SPM ?
>> >> > It is System Power Management which is powered off when system is
>> >> > running in normal mode, and is powered on when system enters suspend
>> >> > mode. It is used to wakeup system when some wakeup sources, such as
>> >> > bluetooth or powerkey etc, tigger wakeup event.
>> >> 
>> >> okay, thanks
>> >> 
>> >> >> >> suspend compeltion, this causes SPM also not notice the resume signal.
>> >> >>            ^^^^^^^^^^
>> >> >>            completion
>> >> >> 
>> >> >> >> So in order to reduce the duration less than 20ms, make use of
>> >> >> >> syscore's suspend/resume interface.
>> >> >> 
>> >> >> no, this is the wrong approach
>> >> > But it seems only one workable approach from software side
>> >> 
>> >> I wouldn't say that. It seems to me SPM should be enabled earlier.
>> > Yes, but normally SPM should be enabled after all CPUS are turned off,
>> > so it's difficult to do that, I mean enable SPM before turning off CPUS
>> 
>> is it a requirement that SPM should be enabled only after all CPUs are
>> turned off ? If that's the case, then any device in the system might
>> have missed wakeups. This doesn't seem like a good design to me; unless
>> I'm missing something...
> Yes, it's a requirement.
>
> If the wakeup source is level trigger, and will keep it until SPM notice
> it. Although USB wakeup is level trigger, but it just last at most 20ms
> and clear itself automatically.

who's clearing USB wakeup after 20ms ? Sure, it's a requirement by the
USB spec that host should drive reset for *at least* 20ms, but I don't
remember the exact wordings WRT remote wakeup

/me reads

Okay, here it is, section 7.1.7.7 of USB 2.0 Spec states:

	"The remote wakeup device must hold the resume signaling for at
        least 1 ms but for no more than 15 ms (TDRSMUP). At the end of
        this period, the device stops driving the bus (puts its drivers
        into the high-impedance state and does not drive the bus to the
        J state)."

IOW, the mouse is not at fault here. Remote wakeup can last anywhere
between 1ms and 15ms. If your system can't cope with it, then I'd say
it's a problem with your system and you shouldn't allow XHCI to go to
such deep power states until SPM is enabled.

I really tried finding the correct piece of code which does this for PCI
devices, but basically it's treated as an IRQ and as long as
enable_irq_wake() or the sysfs file is set to true, then PME gets
enabled (hopefully PCI folks can confirm this statement).

Very recently Tony Lindgren added proper handling of wakeup signals as
IRQs for non-PCI systems too (see 4990d4fe327b PM / Wakeirq: Add
automated device wake IRQ handling), wonder if you could treat SPM
similarly.

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 818 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-mediatek/attachments/20160504/bec02f4f/attachment-0001.sig>