[PATCH 1/3] mmc: mmc: use ops->card_busy() to check card status in __mmc_switch()

Ulf Hansson ulf.hansson at linaro.org
Tue Jun 21 06:15:51 PDT 2016


On 19 May 2016 at 10:47, Chaotian Jing <chaotian.jing at mediatek.com> wrote:
> some MMC host do not support MMC_CAP_WAIT_WHILE_BUSY but provides
> ops->card_busy(), So, add this method to check card status after
> switch command.
>
> Signed-off-by: Chaotian Jing <chaotian.jing at mediatek.com>

Thanks, applied for next! (With some minor updates to the change log)

Kind regards
Uffe

> ---
>  drivers/mmc/core/mmc_ops.c | 25 ++++++++++++++++---------
>  1 file changed, 16 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> index 62355bd..32de144 100644
> --- a/drivers/mmc/core/mmc_ops.c
> +++ b/drivers/mmc/core/mmc_ops.c
> @@ -480,6 +480,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
>         u32 status = 0;
>         bool use_r1b_resp = use_busy_signal;
>         bool expired = false;
> +       bool busy = false;
>
>         mmc_retune_hold(host);
>
> @@ -535,19 +536,24 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
>         /* Must check status to be sure of no errors. */
>         timeout = jiffies + msecs_to_jiffies(timeout_ms);
>         do {
> +               /*
> +                * Due to the possibility of being preempted after
> +                * sending the status command, check the expiration
> +                * time first.
> +                */
> +               expired = time_after(jiffies, timeout);
>                 if (send_status) {
> -                       /*
> -                        * Due to the possibility of being preempted after
> -                        * sending the status command, check the expiration
> -                        * time first.
> -                        */
> -                       expired = time_after(jiffies, timeout);
>                         err = __mmc_send_status(card, &status, ignore_crc);
>                         if (err)
>                                 goto out;
>                 }
>                 if ((host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp)
>                         break;
> +               if (host->ops->card_busy) {
> +                       if (!host->ops->card_busy(host))
> +                               break;
> +                       busy = true;
> +               }
>                 if (mmc_host_is_spi(host))
>                         break;
>
> @@ -556,19 +562,20 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
>                  * does'nt support MMC_CAP_WAIT_WHILE_BUSY, then we can only
>                  * rely on waiting for the stated timeout to be sufficient.
>                  */
> -               if (!send_status) {
> +               if (!send_status && !host->ops->card_busy) {
>                         mmc_delay(timeout_ms);
>                         goto out;
>                 }
>
>                 /* Timeout if the device never leaves the program state. */
> -               if (expired && R1_CURRENT_STATE(status) == R1_STATE_PRG) {
> +               if (expired &&
> +                   (R1_CURRENT_STATE(status) == R1_STATE_PRG || busy)) {
>                         pr_err("%s: Card stuck in programming state! %s\n",
>                                 mmc_hostname(host), __func__);
>                         err = -ETIMEDOUT;
>                         goto out;
>                 }
> -       } while (R1_CURRENT_STATE(status) == R1_STATE_PRG);
> +       } while (R1_CURRENT_STATE(status) == R1_STATE_PRG || busy);
>
>         err = mmc_switch_status_error(host, status);
>  out:
> --
> 1.8.1.1.dirty
>



More information about the Linux-mediatek mailing list