[RFC PATCH 3/5] dt-bindings: thermal: Add optional properties of Mediatek thermal controller
Pi-Cheng Chen
pi-cheng.chen at linaro.org
Sun Jan 24 16:21:20 PST 2016
On Fri, Jan 22, 2016 at 04:31:36PM -0600, Rob Herring wrote:
> On Fri, Jan 22, 2016 at 04:40:27PM +0800, Pi-Cheng Chen wrote:
> > This adds optional properties of Mediatek thermal controller which are
> > required by SVS engine integrated with Mediatek thermal controller.
> >
> > Signed-off-by: Pi-Cheng Chen <pi-cheng.chen at linaro.org>
> > ---
> > .../bindings/thermal/mediatek-thermal.txt | 23 ++++++++++++++++------
> > 1 file changed, 17 insertions(+), 6 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
> > index 81f9a51..acaacaa 100644
> > --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
> > +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
> > @@ -7,6 +7,11 @@ this device needs phandles to the AUXADC. Also it controls a mux in the
> > apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS
> > is also needed.
> >
> > +There is another hardware engine, SVS (Smart Voltage Scaling) which shares the
> > +same block of banked registers with Mediatek thermal controller. Hence the
> > +driver of SVS is integrated with the driver of Mediatek thermal controller. The
> > +properties required by SVS engine are optional for Mediatek thermal controller.
> > +
> > Required properties:
> > - compatible: "mediatek,mt8173-thermal"
> > - reg: Address range of the thermal controller
> > @@ -21,9 +26,15 @@ Required properties:
> > - #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
> >
> > Optional properties:
> > -- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
> > - unspecified default values shall be used.
> > -- nvmem-cell-names: Should be "calibration-data"
> > +- clocks, clock-names: Clocks that are optional for the thermal controller.
> > + Specify to enable SVS engine.
> > + "svs_pll": The PLL clock should be switched to during
> > + initialization stage of SVS engine.
> > + "svs_mux": The MUX clock controls the clock input of SVS engine.
> > +- nvmem-cells: A list of phandles to the calibration data provided by a nvmem
> > + device. If unspecified default values shall be used. The SVS
> > + engine will be disabled if no SVS calibration data is specified.
> > +- nvmem-cell-names: Should be "calibration-data" and "svs-calibration-data"
> >
> > Example:
> >
> > @@ -33,11 +44,11 @@ Example:
> > reg = <0 0x1100b000 0 0x1000>;
> > interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
> > clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
> > - clock-names = "therm", "auxadc";
> > + clock-names = "therm", "auxadc", ;
>
> Huh?
>
It should be:
clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>,
<&topckgen CLK_TOP_SYSPLL1_D2>, <&topckgen CLK_TOP_AXI_SEL>;
clock-names = "therm", "auxadc", "svs_pll", "svs_mux";
Sorry for my mistake.
> > resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
> > reset-names = "therm";
> > mediatek,auxadc = <&auxadc>;
> > mediatek,apmixedsys = <&apmixedsys>;
> > - nvmem-cells = <&thermal_calibration_data>;
> > - nvmem-cell-names = "calibration-data";
> > + nvmem-cells = <&thermal_calibration_data>, <&svs-calibration>;
> > + nvmem-cell-names = "calibration-data", "svs-calibration-data";
> > };
> > --
> > 1.9.1
> >
More information about the Linux-mediatek
mailing list