[RFC v2 1/6] drm/mediatek: hdmi: Add audio interface to the hdmi-codec driver

[Russell King - ARM Linux]

On Mon, Jan 04, 2016 at 08:09:06PM +0100, Philipp Zabel wrote:
> Add the interface needed by Jyri's generic hdmi-codec driver [1] to start
> or stop audio playback and to retrieve ELD (EDID like data) to limit the
> supported audio formats to the HDMI sink capabilities.

Some of this makes me rather suspicious.

> +	switch (params->sample_rate) {
> +	case 32000:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_32000;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_32K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0x3;
> +		break;
> +	case 44100:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_44100;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_44K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0;
> +		break;
> +	case 48000:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_48000;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_48K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0x2;
> +		break;
> +	case 88200:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_88200;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_88K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0x8;
> +		break;
> +	case 96000:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_96000;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_96K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0xa;
> +		break;
> +	case 176400:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_176400;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_176K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0xc;
> +		break;
> +	case 192000:
> +		hdmi_params.aud_hdmi_fs = HDMI_AUDIO_SAMPLE_FREQUENCY_192000;
> +		hdmi_params.iec_frame_fs = HDMI_IEC_192K;
> +		/* channel status byte 3: fs and clock accuracy */
> +		hdmi_params.hdmi_l_channel_state[3] = 0xe;

For exmaple, all the above.  The HDMI standards say that the audio info
frame "shall" always set the sample frequency to "refer to stream" for
L-PCM and IEC61937 compressed audio.  The above looks like it violates
the HDMI specification as I'm willing to bet that hdmi_params.aud_hdmi_fs
gets passed over into the audio info frame.

Many of the fields in the audio info frame are supposed to be set as
"refer to stream".  I'd suggest ensuring that you're compliant with
these.

The second thing is that "hdmi_params.hdmi_l_channel_state" looks like
it's the IEC958 bytes.  These must be correct for some of the higher
end HDMI receivers (eg, Yamaha RX-V677) to correctly process the audio.

> +		break;
> +	default:
> +		dev_err(hdmi->dev, "rate[%d] not supported!\n",
> +			params->sample_rate);
> +		return -EINVAL;
> +	}
> +
> +	switch (daifmt->fmt) {
> +	case HDMI_I2S:
> +		hdmi_params.aud_codec = HDMI_AUDIO_CODING_TYPE_PCM;
> +		hdmi_params.aud_sampe_size = HDMI_AUDIO_SAMPLE_SIZE_16;
> +		hdmi_params.aud_input_type = HDMI_AUD_INPUT_I2S;
> +		hdmi_params.aud_i2s_fmt = HDMI_I2S_MODE_I2S_24BIT;
> +		hdmi_params.aud_mclk = HDMI_AUD_MCLK_128FS;
> +		break;
> +	default:
> +		dev_err(hdmi->dev, "%s: Invalid format %d\n", __func__,
> +			daifmt->fmt);
> +		return -EINVAL;
> +	}
> +
> +	/* channel status */
> +	/* byte 0: no copyright is asserted, mode 0 */
> +	hdmi_params.hdmi_l_channel_state[0] = 1 << 2;
> +	/* byte 1: category code */
> +	hdmi_params.hdmi_l_channel_state[1] = 0;
> +	/* byte 2: source/channel number don't take into account */
> +	hdmi_params.hdmi_l_channel_state[2] = 0;
> +	/* byte 4: word length 16bits */
> +	hdmi_params.hdmi_l_channel_state[4] = 0x2;
> +	memcpy(hdmi_params.hdmi_r_channel_state,
> +	       hdmi_params.hdmi_l_channel_state,
> +	       sizeof(hdmi_params.hdmi_l_channel_state));

Hmm, yes, it is the IEC958 channel status bytes.  We have a helper
for this - snd_pcm_create_iec958_consumer().

-- 
RMK's Patch system: http://www.arm.linux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.