[PATCH 3/3] arm: dts: thermal: add thermal/auxadc node.
Matthias Brugger
matthias.bgg at gmail.com
Mon Aug 22 10:09:56 PDT 2016
On 15/08/16 09:14, dawei chien wrote:
> Hi Matthias,
>
> On Thu, 2016-08-11 at 17:51 +0200, Matthias Brugger wrote:
>>
>> On 07/07/16 11:06, Dawei Chien wrote:
>>> This adds the thermal controller and auxadc nodes
>>> to the Mediatek MT2701 dtsi file.
>>>
>>> Signed-off-by: Dawei Chien <dawei.chien at mediatek.com>
>>> ---
>>> This patch depned on:
>>> https://patchwork.kernel.org/patch/9213545/
>>> ---
>>> arch/arm/boot/dts/mt2701.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 43 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
>>> index 2ac8b50..0834a23 100644
>>> --- a/arch/arm/boot/dts/mt2701.dtsi
>>> +++ b/arch/arm/boot/dts/mt2701.dtsi
>>> @@ -77,6 +77,36 @@
>>> #clock-cells = <0>;
>>> };
>>>
>>> + thermal-zones {
>>> + cpu_thermal: cpu_thermal {
>>> + polling-delay-passive = <1000>; /* milliseconds */
>>> + polling-delay = <1000>; /* milliseconds */
>>> +
>>> + thermal-sensors = <&thermal 0>;
>>> + sustainable-power = <1000>;
>>> +
>>> + trips {
>>> + threshold: trip-point at 0 {
>>> + temperature = <68000>;
>>> + hysteresis = <2000>;
>>> + type = "passive";
>>> + };
>>> +
>>> + target: trip-point at 1 {
>>> + temperature = <85000>;
>>> + hysteresis = <2000>;
>>> + type = "passive";
>>> + };
>>> +
>>> + cpu_crit: cpu_crit at 0 {
>>> + temperature = <115000>;
>>> + hysteresis = <2000>;
>>> + type = "critical";
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> timer {
>>> compatible = "arm,armv7-timer";
>>> interrupt-parent = <&gic>;
>>> @@ -183,4 +213,17 @@
>>> clocks = <&uart_clk>;
>>> status = "disabled";
>>> };
>>> +
>>> + thermal: thermal at 1100b000 {
>>> + #thermal-sensor-cells = <0>;
>>> + compatible = "mediatek,mt2701-thermal";
>>> + reg = <0 0x1100b000 0 0x1000>;
>>> + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>;
>>> + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
>>> + clock-names = "therm", "auxadc";
>>> + resets = <&pericfg 0x10>;
>>> + reset-names = "therm";
>>> + mediatek,auxadc = <&auxadc>;
>>> + mediatek,apmixedsys = <&apmixedsys>;
>>> + };
>>> };
>>>
>>
>> what about:
>> status = "disabled"; ?
>
> Since thermal driver would protect our platform by shutdown method once
> SoC temperature over critical point, I prefer keep this rather than
> disabling, how do you think, thank you.
>
Sounds reasonable. Thanks
More information about the Linux-mediatek
mailing list