[PATCH v3 1/2] mtd: mediatek: device tree docs for MTK Smart Device Gen1 NAND

Jorge Ramirez-Ortiz jorge.ramirez-ortiz at linaro.org
Mon Apr 11 18:17:37 PDT 2016


On 04/11/2016 07:15 PM, Boris Brezillon wrote:
> On Mon, 11 Apr 2016 12:56:11 -0400
> Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org> wrote:
>
>> This patch adds documentation support for Smart Device Gen1 type of
>> NAND controllers.
>>
>> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
>> ---
>>  Documentation/devicetree/bindings/mtd/mtk-nand.txt | 145 +++++++++++++++++++++
>>  1 file changed, 145 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
>> new file mode 100644
>> index 0000000..ca3cc95
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
>> @@ -0,0 +1,145 @@
>> +MTK SoCs NAND FLASH controller (NFC) DT binding
>> +
>> +This file documents the device tree bindings for MTK SoCs NAND controllers.
>> +The functional split of the controller requires two drivers to operate:
>> +the nand controller interface driver and the ECC engine driver.
>> +
>> +The hardware description for both devices must be captured as device
>> +tree nodes.
>> +
>> +1) NFC NAND Controller Interface (NFI):
>> +=======================================
>> +
>> +The first part of NFC is NAND Controller Interface (NFI) HW.
>> +Required NFI properties:
>> +- compatible:			Should be "mediatek,mtxxxx-nfc".
>> +- reg:				Base physical address and size of NFI.
>> +- interrupts:			Interrupts of NFI.
>> +- clocks:			NFI required clocks.
>> +- clock-names:			NFI clocks internal name.
>> +- status:			Disabled default. Then set "okay" by platform.
>> +- ecc-engine:			Required ECC Engine node.
>> +- #address-cells:		NAND chip index, should be 1.
>> +- #size-cells:			Should be 0.
>> +
>> +Example:
>> +
>> +	nandc: nfi at 1100d000 {
>> +		compatible = "mediatek,mt2701-nfc";
>> +		reg = <0 0x1100d000 0 0x1000>;
>> +		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
>> +		clocks = <&pericfg CLK_PERI_NFI>,
>> +			 <&pericfg CLK_PERI_NFI_PAD>;
>> +		clock-names = "nfi_clk", "pad_clk";
>> +		status = "disabled";
>> +		ecc-engine = <&bch>;
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +        };
>> +
>> +Platform related properties, should be set in {platform_name}.dts:
>> +- children nodes:	NAND chips.
>> +
>> +Children nodes properties:
>> +- reg:			Chip Select Signal, default 0.
>> +			Set as reg = <0>, <1> when need 2 CS.
>> +- spare_per_sector:	Spare size of each sector.
> Do you really need this property? It should be deduced from ECC
> strength/step-size and oobsize info (or any other NFC/ECC constraints).
>
>

I think so.

the set of valid values for SPARE_PER_SECTOR is actually defined in the product
data sheet (NFI_PAGEFMT register bits 7:4)
the 16 valid values are (in Bytes) 16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50,
51, 52,62, 63 and 64.

I suppose we could do some maths (oobsize/step size) and approximate to these
values but we thought it would be simpler just to actually code the right value
in the device tree?



 






More information about the Linux-mediatek mailing list