[PATCH 2/3] thermal: Add Mediatek thermal controller support
Sascha Hauer
s.hauer at pengutronix.de
Tue Sep 29 23:13:49 PDT 2015
Hi Eduardo,
On Tue, Sep 29, 2015 at 04:04:40PM -0700, Eduardo Valentin wrote:
> On Wed, Sep 23, 2015 at 03:37:42PM +0200, Sascha Hauer wrote:
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_irq.h>
>
> You dont seam to be using this header. Can you please clean up to have
> only the headers you need?
Ok, did that.
> > + struct mtk_thermal *mt = bank->mt;
> > + int temp, i, max;
> > + u32 raw;
> > +
> > + temp = max = INT_MIN;
> > +
> > + for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
> > + raw = readl(mt->thermal_base + sensing_points[i].msr);
> > +
> > + temp = raw_to_mcelsius(mt, raw);
> > +
> > + /*
> > + * The first read of a sensor often contains very high bogus
> > + * temperature value. Filter these out so that the system does
> > + * not immediately shut down.
> > + */
> > + if (temp > 200000)
>
> Ok... How about after the first read? is > 200000 a valid (supported) value range?
No, temperatures over 200°C are not supported for this SoC.
> > +
> > + mt->dev = &pdev->dev;
> > +
> > + auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
> of_put?
added
> > + if (!auxadc) {
> > + dev_err(&pdev->dev, "missing auxadc node\n");
> > + return -ENODEV;
> > + }
> > +
> > + auxadc_phys_base = of_get_phys_base(auxadc);
> > + if (auxadc_phys_base == OF_BAD_ADDR) {
> > + dev_err(&pdev->dev, "Can't get auxadc phys address\n");
> > + return -EINVAL;
> > + }
> > +
> > + apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
> > + if (!apmixedsys) {
> > + dev_err(&pdev->dev, "missing apmixedsys node\n");
> > + return -ENODEV;
> > + }
For this one aswell.
> > + /*
> > + * These calibration values should finally be provided by the
> > + * firmware or fuses. For now use default values.
> > + */
> > + mt->calib_slope = -123;
> > + mt->calib_offset = 465124;
>
> I would still prefer that this driver would not have these hardcoded
> values. Specially considering the fact that we could map it in DT for
> instance. What is the impact of using this? Does it work across all chip
> distribution?
I think yes, but not that accurate.
>
> Should we wait until you have the code to read the fuses before merging
> this?
I'd say we should merge this. It makes the life easier for the guys
writing the cpufreq driver. Adding a dependency on a not yet written
driver IMO only adds unnecessary delays.
>
> > +
> > + for (i = 0; i < MT8173_NUM_ZONES; i++)
> > + mtk_thermal_init_bank(mt, i, apmixed_phys_base, auxadc_phys_base);
> > +
> > + platform_set_drvdata(pdev, mt);
> > +
> > + for (i = 0; i < MT8173_NUM_ZONES; i++) {
> > + struct mtk_thermal_bank *bank = &mt->banks[i];
> > +
> > + bank->tzd = thermal_zone_of_sensor_register(&pdev->dev, i, bank,
> > + &mtk_thermal_ops);
>
> You need to error handle this.
Errors here are pretty much expected. This is due to the behaviour of
thermal_zone_of_sensor_register which errors out when no user for a
sensor is found. Normally I would expect that I can register a sensor
regardless if it is used or not, but that's not how
thermal_zone_of_sensor_register is written.
I could catch -EPROBE_DEFER here, but currently I see no case where this
can actually be returned from thermal_zone_of_sensor_register.
What I can and should do though is to call
thermal_zone_of_sensor_unregister only for sensors that are successfully
registered.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the Linux-mediatek
mailing list