[PATCH v8 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs
Kishon Vijay Abraham I
kishon at ti.com
Thu Sep 17 23:42:18 PDT 2015
Hi,
On Wednesday 16 September 2015 12:14 PM, Chunfeng Yun wrote:
> support usb3.0 phy of mt65xx SoCs
few nitpicks:
change $subject. This driver is no longer in usb directory.
It can be just "phy: add usb3.0 phy driver for mt65xx SoCs".
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> ---
> drivers/phy/Kconfig | 9 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-mt65xx-usb3.c | 456 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 466 insertions(+)
> create mode 100644 drivers/phy/phy-mt65xx-usb3.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..ec436c1 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -206,6 +206,15 @@ config PHY_HIX5HD2_SATA
> help
> Support for SATA PHY on Hisilicon hix5hd2 Soc.
>
> +config PHY_MT65XX_USB3
> + tristate "Mediatek USB3.0 PHY Driver"
> + depends on ARCH_MEDIATEK && OF
> + select GENERIC_PHY
> + help
> + Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> + for mt65xx SoCs. it supports two usb2.0 ports and
> + one usb3.0 port.
> +
> config PHY_SUN4I_USB
> tristate "Allwinner sunxi SoC USB PHY driver"
> depends on ARCH_SUNXI && HAS_IOMEM && OF
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..a7cc629 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -23,6 +23,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
> obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
> +obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o
> obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o
> obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.o
> diff --git a/drivers/phy/phy-mt65xx-usb3.c b/drivers/phy/phy-mt65xx-usb3.c
> new file mode 100644
> index 0000000..1f00b05
> --- /dev/null
> +++ b/drivers/phy/phy-mt65xx-usb3.c
> @@ -0,0 +1,456 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Chunfeng Yun <chunfeng.yun at mediatek.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <dt-bindings/phy/phy.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +/*
> + * for sifslv2 register, but exclude port's;
> + * relative to USB3_SIF2_BASE base address
> + */
> +#define SSUSB_SIFSLV_SPLLC 0x0000
> +
> +/* offsets of sub-segment in each port registers */
> +#define SSUSB_SIFSLV_U2PHY_COM_BASE 0x0000
> +#define SSUSB_SIFSLV_U3PHYD_BASE 0x0100
> +#define SSUSB_USB30_PHYA_SIV_B_BASE 0x0300
> +#define SSUSB_SIFSLV_U3PHYA_DA_BASE 0x0400
> +
> +#define U3P_USBPHYACR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> +#define PA0_RG_U2PLL_FORCE_ON BIT(15)
> +
> +#define U3P_USBPHYACR2 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> +#define PA2_RG_SIF_U2PLL_FORCE_EN BIT(18)
> +
> +#define U3P_USBPHYACR5 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> +#define PA5_RG_U2_HSTX_SRCTRL GENMASK(14, 12)
> +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x) ((0x7 & (x)) << 12)
> +#define PA5_RG_U2_HS_100U_U3_EN BIT(11)
> +
> +#define U3P_USBPHYACR6 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> +#define PA6_RG_U2_ISO_EN BIT(31)
> +#define PA6_RG_U2_BC11_SW_EN BIT(23)
> +#define PA6_RG_U2_OTG_VBUSCMP_EN BIT(20)
> +
> +#define U3P_U2PHYACR4 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> +#define P2C_RG_USB20_GPIO_CTL BIT(9)
> +#define P2C_USB20_GPIO_MODE BIT(8)
> +#define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> +
> +#define U3D_U2PHYDCR0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> +#define P2C_RG_SIF_U2PLL_FORCE_ON BIT(24)
> +
> +#define U3P_U2PHYDTM0 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> +#define P2C_FORCE_UART_EN BIT(26)
> +#define P2C_FORCE_DATAIN BIT(23)
> +#define P2C_FORCE_DM_PULLDOWN BIT(21)
> +#define P2C_FORCE_DP_PULLDOWN BIT(20)
> +#define P2C_FORCE_XCVRSEL BIT(19)
> +#define P2C_FORCE_SUSPENDM BIT(18)
> +#define P2C_FORCE_TERMSEL BIT(17)
> +#define P2C_RG_DATAIN GENMASK(13, 10)
> +#define P2C_RG_DATAIN_VAL(x) ((0xf & (x)) << 10)
> +#define P2C_RG_DMPULLDOWN BIT(7)
> +#define P2C_RG_DPPULLDOWN BIT(6)
> +#define P2C_RG_XCVRSEL GENMASK(5, 4)
> +#define P2C_RG_XCVRSEL_VAL(x) ((0x3 & (x)) << 4)
> +#define P2C_RG_SUSPENDM BIT(3)
> +#define P2C_RG_TERMSEL BIT(2)
> +#define P2C_DTM0_PART_MASK \
> + (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> + P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> + P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> + P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> +
> +#define U3P_U2PHYDTM1 (SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> +#define P2C_RG_UART_EN BIT(16)
> +#define P2C_RG_VBUSVALID BIT(5)
> +#define P2C_RG_SESSEND BIT(4)
> +#define P2C_RG_AVALID BIT(2)
> +
> +#define U3P_U3_PHYA_REG0 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> +#define P3A_RG_U3_VUSB10_ON BIT(5)
> +
> +#define U3P_U3_PHYA_REG6 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> +#define P3A_RG_TX_EIDLE_CM GENMASK(31, 28)
> +#define P3A_RG_TX_EIDLE_CM_VAL(x) ((0xf & (x)) << 28)
> +
> +#define U3P_U3_PHYA_REG9 (SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> +#define P3A_RG_RX_DAC_MUX GENMASK(5, 1)
> +#define P3A_RG_RX_DAC_MUX_VAL(x) ((0x1f & (x)) << 1)
> +
> +#define U3P_U3PHYA_DA_REG0 (SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0000)
> +#define P3A_RG_XTAL_EXT_EN_U3 GENMASK(11, 10)
> +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x) ((0x3 & (x)) << 10)
> +
> +#define U3P_PHYD_CDR1 (SSUSB_SIFSLV_U3PHYD_BASE + 0x005c)
> +#define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24)
> +#define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24)
> +#define P3D_RG_CDR_BIR_LTD0 GENMASK(12, 8)
> +#define P3D_RG_CDR_BIR_LTD0_VAL(x) ((0x1f & (x)) << 8)
> +
> +#define U3P_XTALCTL3 (SSUSB_SIFSLV_SPLLC + 0x0018)
> +#define XC3_RG_U3_XTAL_RX_PWD BIT(9)
> +#define XC3_RG_U3_FRC_XTAL_RX_PWD BIT(8)
> +
> +struct mt65xx_phy_instance {
> + struct phy *phy;
> + void __iomem *port_base;
> + u32 index;
> + u8 type;
> +};
> +
> +struct mt65xx_u3phy {
> + struct device *dev;
> + void __iomem *sif_base; /* include sif2, but exclude port's */
> + struct clk *u3phya_ref; /* reference clock of usb3 anolog phy */
> + struct mt65xx_phy_instance **phys;
> + int nphys;
> +};
> +
> +static void phy_instance_init(struct mt65xx_u3phy *u3phy,
> + struct mt65xx_phy_instance *instance)
> +{
> + void __iomem *port_base = instance->port_base;
> + u32 index = instance->index;
> + u32 tmp;
> +
> + /* switch to USB function. (system register, force ip into usb mode) */
> + tmp = readl(port_base + U3P_U2PHYDTM0);
> + tmp &= ~P2C_FORCE_UART_EN;
> + writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> + tmp = readl(port_base + U3P_U2PHYDTM1);
> + tmp &= ~P2C_RG_UART_EN;
> + writel(tmp, port_base + U3P_U2PHYDTM1);
> +
> + if (!index) {
> + tmp = readl(port_base + U3P_U2PHYACR4);
> + tmp &= ~P2C_U2_GPIO_CTR_MSK;
> + writel(tmp, port_base + U3P_U2PHYACR4);
> + }
> +
> + /* DP/DM BC1.1 path Disable */
> + tmp = readl(port_base + U3P_USBPHYACR6);
> + tmp &= ~PA6_RG_U2_BC11_SW_EN;
> + writel(tmp, port_base + U3P_USBPHYACR6);
> +
> + tmp = readl(port_base + U3P_U3PHYA_DA_REG0);
> + tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
> + tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
> + writel(tmp, port_base + U3P_U3PHYA_DA_REG0);
> +
> + tmp = readl(port_base + U3P_U3_PHYA_REG9);
> + tmp &= ~P3A_RG_RX_DAC_MUX;
> + tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
> + writel(tmp, port_base + U3P_U3_PHYA_REG9);
> +
> + tmp = readl(port_base + U3P_U3_PHYA_REG6);
> + tmp &= ~P3A_RG_TX_EIDLE_CM;
> + tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
> + writel(tmp, port_base + U3P_U3_PHYA_REG6);
> +
> + tmp = readl(port_base + U3P_PHYD_CDR1);
> + tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
> + tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
> + writel(tmp, port_base + U3P_PHYD_CDR1);
> +
> + dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> +}
> +
> +static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
> + struct mt65xx_phy_instance *instance)
> +{
> + void __iomem *port_base = instance->port_base;
> + u32 index = instance->index;
> + u32 tmp;
> +
> + if (!index) {
> + /* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> + tmp = readl(port_base + U3P_U3_PHYA_REG0);
> + tmp |= P3A_RG_U3_VUSB10_ON;
> + writel(tmp, port_base + U3P_U3_PHYA_REG0);
> + }
> +
> + /* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> + tmp = readl(port_base + U3P_U2PHYDTM0);
> + tmp &= ~(P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL);
> + tmp &= ~(P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> + writel(tmp, port_base + U3P_U2PHYDTM0);
> +
> + /* OTG Enable */
> + tmp = readl(port_base + U3P_USBPHYACR6);
> + tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
> + writel(tmp, port_base + U3P_USBPHYACR6);
> +
> + if (!index) {
> + tmp = readl(u3phy->sif_base + U3P_XTALCTL3);
> + tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
> + writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
> + /* [mt8173]disable Change 100uA current from SSUSB */
> + tmp = readl(port_base + U3P_USBPHYACR5);
> + tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
> + writel(tmp, port_base + U3P_USBPHYACR5);
> + }
> + udelay(800);
It's good to document delay values. Is it a recommended value from the
data manual?
Also now the registers doesn't seem to be shared between the PHYs. But
if it is then all these functions have to be protected with spinlock.
Thanks
Kishon
More information about the Linux-mediatek
mailing list