[PATCH v3 3/4] spi: mediatek: Add spi bus for Mediatek MT8173

leilk liu leilk.liu at mediatek.com
Sun Jul 26 19:48:47 PDT 2015


On Fri, 2015-07-24 at 18:49 +0100, Mark Brown wrote:
> On Thu, Jul 23, 2015 at 05:10:42PM +0800, Leilk Liu wrote:
> 
> This basically seems fine but there's a couple of issues that should be
> relatively easy to fix:
> 
> > +	mdata->cur_transfer = xfer;
> > +	mtk_spi_prepare_transfer(master, xfer);
> > +	mtk_spi_setup_packet(master, xfer);
> > +
> > +	cnt = (xfer->len % 4) ? (xfer->len / 4 + 1) : (xfer->len / 4);
> 
> Please write this as an if statement for legibility.
> 

OK, I'll fix it.

> > +static bool mtk_spi_can_dma(struct spi_master *master,
> > +			    struct spi_device *spi,
> > +			    struct spi_transfer *xfer)
> > +{
> > +	struct mtk_spi *mdata = spi_master_get_devdata(master);
> > +
> > +	if (xfer->len > MTK_SPI_MAX_FIFO_SIZE)
> > +		mdata->use_dma = true;
> > +	else
> > +		mdata->use_dma = false;
> > +
> > +	return mdata->use_dma;
> > +}
> 
> This is broken since can_dma() can be called multiple transfers before
> actually doing a transfer (the current implementation loops over all
> transfers in a message before starting the message) - you can't store
> any local data.  The transfer_one() function should do another can_dma()
> check to decide if it can DMA, it shouldn't rely on driver global data.  
> 

OK, I'll fix it.

> > +	if (!mdata->use_dma) {
> > +		if (trans->rx_buf) {
> 
> This should be a variable set when doing the transfer (or perhaps based
> on checking spi->cur_xfer with can_dma()). 
> 
> > +			for (i = 0; i < trans->len; i++) {
> > +				if (i % 4 == 0)
> > +					reg_val =
> > +					readl(mdata->base + SPI_RX_DATA_REG);
> > +				*((u8 *)(trans->rx_buf + i)) =
> > +					(reg_val >> ((i % 4) * 8)) & 0xff;
> 
> This isn't the clearest code ever...  a comment would help.
> 
OK, I'll fix it.

> > +	if (mdata->tx_sgl && (mdata->tx_sgl_len == 0)) {
> > +		mdata->tx_sgl = sg_next(mdata->tx_sgl);
> > +		if (mdata->tx_sgl) {
> > +			trans->tx_dma = sg_dma_address(mdata->tx_sgl);
> > +			mdata->tx_sgl_len = sg_dma_len(mdata->tx_sgl);
> > +		}
> > +	}
> 
> There's a *lot* of code in this interrupt handler, and a lot of it looks
> an awful lot like the contents of mtk_spi_dma_transfer() has been
> cut'n'pasted in.  The shared code should all be factored out into a
> function called from both places.

OK, I'll fix it.





More information about the Linux-mediatek mailing list