[PATCH 1/2] cs5535-gpio: add AMD CS5535/CS5536 GPIO driver support
Andres Salomon
dilinger at collabora.co.uk
Wed Jun 10 00:10:33 EDT 2009
I'm resubmitting this, as I actually have time to deal w/ any problems
it might have. Randy, please do your worst (and send me a .config if
you find problems!). Thanks.
Oh, also, I renamed it to cs5535-gpio at the request of q-funk, in
order to be consistent w/ naming standards for CS5530/CS5535/CS5536.
This creates a CS5535/CS5536 GPIO driver which uses a gpio_chip backend
(allowing GPIO users to use the generic GPIO API if desired) while also
allowing architecture-specific users directly (via the cs5535_gpio_*
functions).
Tested on an OLPC machine. Some Leemotes also use CS5536 (with a mips
cpu), which is why this is in drivers/gpio rather than arch/x86.
Currently, it conflicts with older geode GPIO support; once MFGPT support
is reworked to also be more generic, the older geode code will be removed.
Signed-off-by: Andres Salomon <dilinger at collabora.co.uk>
---
arch/x86/include/asm/geode.h | 28 +----
drivers/gpio/Kconfig | 10 ++
drivers/gpio/Makefile | 1 +
drivers/gpio/cs5535-gpio.c | 282 ++++++++++++++++++++++++++++++++++++++++++
include/linux/cs5535.h | 58 +++++++++
5 files changed, 352 insertions(+), 27 deletions(-)
create mode 100644 drivers/gpio/cs5535-gpio.c
create mode 100644 include/linux/cs5535.h
diff --git a/arch/x86/include/asm/geode.h b/arch/x86/include/asm/geode.h
index ad3c2ed..5716214 100644
--- a/arch/x86/include/asm/geode.h
+++ b/arch/x86/include/asm/geode.h
@@ -12,6 +12,7 @@
#include <asm/processor.h>
#include <linux/io.h>
+#include <linux/cs5535.h>
/* Generic southbridge functions */
@@ -115,33 +116,6 @@ extern int geode_get_dev_base(unsigned int dev);
#define VSA_VR_MEM_SIZE 0x0200
#define AMD_VSA_SIG 0x4132 /* signature is ascii 'VSA2' */
#define GSW_VSA_SIG 0x534d /* General Software signature */
-/* GPIO */
-
-#define GPIO_OUTPUT_VAL 0x00
-#define GPIO_OUTPUT_ENABLE 0x04
-#define GPIO_OUTPUT_OPEN_DRAIN 0x08
-#define GPIO_OUTPUT_INVERT 0x0C
-#define GPIO_OUTPUT_AUX1 0x10
-#define GPIO_OUTPUT_AUX2 0x14
-#define GPIO_PULL_UP 0x18
-#define GPIO_PULL_DOWN 0x1C
-#define GPIO_INPUT_ENABLE 0x20
-#define GPIO_INPUT_INVERT 0x24
-#define GPIO_INPUT_FILTER 0x28
-#define GPIO_INPUT_EVENT_COUNT 0x2C
-#define GPIO_READ_BACK 0x30
-#define GPIO_INPUT_AUX1 0x34
-#define GPIO_EVENTS_ENABLE 0x38
-#define GPIO_LOCK_ENABLE 0x3C
-#define GPIO_POSITIVE_EDGE_EN 0x40
-#define GPIO_NEGATIVE_EDGE_EN 0x44
-#define GPIO_POSITIVE_EDGE_STS 0x48
-#define GPIO_NEGATIVE_EDGE_STS 0x4C
-
-#define GPIO_MAP_X 0xE0
-#define GPIO_MAP_Y 0xE4
-#define GPIO_MAP_Z 0xE8
-#define GPIO_MAP_W 0xEC
static inline u32 geode_gpio(unsigned int nr)
{
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index edb0253..185a458 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -145,6 +145,16 @@ config GPIO_TWL4030
comment "PCI GPIO expanders:"
+config GPIO_CS5535
+ tristate "AMD CS5535/CS5536 GPIO support"
+ depends on PCI && !CS5535_GPIO && !MGEODE_LX
+ help
+ The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
+ can be used for quite a number of things. The CS5535/6 is found on
+ AMD Geode and Lemote Yeeloong devices.
+
+ If unsure, say N.
+
config GPIO_BT8XX
tristate "BT8XX GPIO abuser"
depends on PCI && VIDEO_BT848=n
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 49ac64e..c7bc4bd 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -11,4 +11,5 @@ obj-$(CONFIG_GPIO_PCA953X) += pca953x.o
obj-$(CONFIG_GPIO_PCF857X) += pcf857x.o
obj-$(CONFIG_GPIO_TWL4030) += twl4030-gpio.o
obj-$(CONFIG_GPIO_XILINX) += xilinx_gpio.o
+obj-$(CONFIG_GPIO_CS5535) += cs5535-gpio.o
obj-$(CONFIG_GPIO_BT8XX) += bt8xxgpio.o
diff --git a/drivers/gpio/cs5535-gpio.c b/drivers/gpio/cs5535-gpio.c
new file mode 100644
index 0000000..5613889
--- /dev/null
+++ b/drivers/gpio/cs5535-gpio.c
@@ -0,0 +1,282 @@
+/*
+ * AMD CS5535/CS5536 GPIO driver
+ * Copyright (C) 2006 Advanced Micro Devices, Inc.
+ * Copyright (C) 2007-2009 Andres Salomon <dilinger at collabora.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/cs5535.h>
+
+#define DRV_NAME "cs5535-gpio"
+#define GPIO_BAR 1
+
+static struct cs5535_gpio_chip {
+ struct gpio_chip chip;
+ resource_size_t base;
+
+ struct pci_dev *pdev;
+ spinlock_t lock;
+} cs5535_gpio_chip;
+
+/*
+ * The CS5535/CS5536 GPIOs support a number of extra features not defined
+ * by the gpio_chip API, so these are exported. For a full list of the
+ * registers, see include/linux/cs5535.h.
+ */
+
+static void __cs5535_gpio_set(struct cs5535_gpio_chip *chip, unsigned offset,
+ unsigned int reg)
+{
+ if (offset < 16)
+ /* low bank register */
+ outl(1 << offset, chip->base + reg);
+ else
+ /* high bank register */
+ outl(1 << (offset - 16), chip->base + 0x80 + reg);
+}
+
+void cs5535_gpio_set(unsigned offset, unsigned int reg)
+{
+ struct cs5535_gpio_chip *chip = &cs5535_gpio_chip;
+ unsigned long flags;
+
+ spin_lock_irqsave(&chip->lock, flags);
+ __cs5535_gpio_set(chip, offset, reg);
+ spin_unlock_irqrestore(&chip->lock, flags);
+}
+EXPORT_SYMBOL_GPL(cs5535_gpio_set);
+
+static void __cs5535_gpio_clear(struct cs5535_gpio_chip *chip, unsigned offset,
+ unsigned int reg)
+{
+ if (offset < 16)
+ /* low bank register */
+ outl(1 << (offset + 16), chip->base + reg);
+ else
+ /* high bank register */
+ outl(1 << offset, chip->base + 0x80 + reg);
+}
+
+void cs5535_gpio_clear(unsigned offset, unsigned int reg)
+{
+ struct cs5535_gpio_chip *chip = &cs5535_gpio_chip;
+ unsigned long flags;
+
+ spin_lock_irqsave(&chip->lock, flags);
+ __cs5535_gpio_clear(chip, offset, reg);
+ spin_unlock_irqrestore(&chip->lock, flags);
+}
+EXPORT_SYMBOL_GPL(cs5535_gpio_clear);
+
+int cs5535_gpio_isset(unsigned offset, unsigned int reg)
+{
+ struct cs5535_gpio_chip *chip = &cs5535_gpio_chip;
+ unsigned long flags;
+ long val;
+
+ spin_lock_irqsave(&chip->lock, flags);
+ if (offset < 16)
+ /* low bank register */
+ val = inl(chip->base + reg);
+ else {
+ /* high bank register */
+ val = inl(chip->base + 0x80 + reg);
+ offset -= 16;
+ }
+ spin_unlock_irqrestore(&chip->lock, flags);
+
+ return (val & (1 << offset)) ? 1 : 0;
+}
+EXPORT_SYMBOL_GPL(cs5535_gpio_isset);
+
+/*
+ * Generic gpio_chip API support.
+ */
+
+static int chip_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ return cs5535_gpio_isset(offset, GPIO_OUTPUT_VAL);
+}
+
+static void chip_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
+{
+ if (val)
+ cs5535_gpio_set(offset, GPIO_OUTPUT_VAL);
+ else
+ cs5535_gpio_clear(offset, GPIO_OUTPUT_VAL);
+}
+
+static int chip_direction_input(struct gpio_chip *c, unsigned offset)
+{
+ struct cs5535_gpio_chip *chip = (struct cs5535_gpio_chip *) c;
+ unsigned long flags;
+
+ spin_lock_irqsave(&chip->lock, flags);
+ __cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE);
+ spin_unlock_irqrestore(&chip->lock, flags);
+
+ return 0;
+}
+
+static int chip_direction_output(struct gpio_chip *c, unsigned offset, int val)
+{
+ struct cs5535_gpio_chip *chip = (struct cs5535_gpio_chip *) c;
+ unsigned long flags;
+
+ spin_lock_irqsave(&chip->lock, flags);
+
+ __cs5535_gpio_set(chip, offset, GPIO_OUTPUT_ENABLE);
+ if (val)
+ __cs5535_gpio_set(chip, offset, GPIO_OUTPUT_VAL);
+ else
+ __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_VAL);
+
+ spin_unlock_irqrestore(&chip->lock, flags);
+
+ return 0;
+}
+
+static struct cs5535_gpio_chip cs5535_gpio_chip = {
+ .chip = {
+ .owner = THIS_MODULE,
+ .label = DRV_NAME,
+
+ .base = 0,
+ .ngpio = 28,
+
+ .get = chip_gpio_get,
+ .set = chip_gpio_set,
+
+ .direction_input = chip_direction_input,
+ .direction_output = chip_direction_output,
+ },
+};
+
+static int __init cs5535_gpio_probe(struct pci_dev *pdev,
+ const struct pci_device_id *pci_id)
+{
+ int err;
+
+ /* There are two ways to get the GPIO base address; one is by
+ * fetching it from MSR_LBAR_GPIO, the other is by reading the
+ * PCI BAR info. The latter method is easier (especially across
+ * different architectures), so we'll stick with that for now. If
+ * it turns out to be unreliable in the face of crappy BIOSes, we
+ * can always go back to using MSRs.. */
+
+ err = pci_enable_device_io(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "can't enable device IO\n");
+ goto done;
+ }
+
+ err = pci_request_region(pdev, GPIO_BAR, DRV_NAME);
+ if (err) {
+ dev_err(&pdev->dev, "can't alloc PCI BAR #%d\n", GPIO_BAR);
+ goto done;
+ }
+
+ /* set up the driver-specific struct */
+ cs5535_gpio_chip.base = pci_resource_start(pdev, GPIO_BAR);
+ cs5535_gpio_chip.pdev = pdev;
+ spin_lock_init(&cs5535_gpio_chip.lock);
+
+ dev_info(&pdev->dev, "allocated PCI BAR #%d: base 0x%llx\n", GPIO_BAR,
+ (unsigned long long) cs5535_gpio_chip.base);
+
+ /* finally, register with the generic GPIO API */
+ err = gpiochip_add(&cs5535_gpio_chip.chip);
+ if (err) {
+ dev_err(&pdev->dev, "failed to register gpio chip\n");
+ goto release_region;
+ }
+
+ printk(KERN_INFO DRV_NAME ": GPIO support successfully loaded.\n");
+ return 0;
+
+release_region:
+ pci_release_region(pdev, GPIO_BAR);
+done:
+ return err;
+}
+
+static void __exit cs5535_gpio_remove(struct pci_dev *pdev)
+{
+ int err;
+
+ err = gpiochip_remove(&cs5535_gpio_chip.chip);
+ if (err) {
+ /* uhh? */
+ dev_err(&pdev->dev, "unable to remove gpio_chip?\n");
+ }
+ pci_release_region(pdev, GPIO_BAR);
+}
+
+static struct pci_device_id cs5535_gpio_pci_tbl[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_CS5535_ISA) },
+ { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA) },
+ { 0, },
+};
+MODULE_DEVICE_TABLE(pci, cs5535_gpio_pci_tbl);
+
+/*
+ * We can't use the standard PCI driver registration stuff here, since
+ * that allows only one driver to bind to each PCI device (and we want
+ * multiple drivers to be able to bind to the device). Instead, manually
+ * scan for the PCI device, request a single region, and keep track of the
+ * devices that we're using.
+ */
+
+static int __init cs5535_gpio_scan_pci(void)
+{
+ struct pci_dev *pdev;
+ int err = -ENODEV;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cs5535_gpio_pci_tbl); i++) {
+ pdev = pci_get_device(cs5535_gpio_pci_tbl[i].vendor,
+ cs5535_gpio_pci_tbl[i].device, NULL);
+ if (pdev) {
+ err = cs5535_gpio_probe(pdev, &cs5535_gpio_pci_tbl[i]);
+ if (err)
+ pci_dev_put(pdev);
+
+ /* we only support a single CS5535/6 southbridge */
+ break;
+ }
+ }
+
+ return err;
+}
+
+static void __exit cs5535_gpio_free_pci(void)
+{
+ cs5535_gpio_remove(cs5535_gpio_chip.pdev);
+ pci_dev_put(cs5535_gpio_chip.pdev);
+}
+
+static int __init cs5535_gpio_init(void)
+{
+ return cs5535_gpio_scan_pci();
+}
+
+static void __exit cs5535_gpio_exit(void)
+{
+ cs5535_gpio_free_pci();
+}
+
+module_init(cs5535_gpio_init);
+module_exit(cs5535_gpio_exit);
+
+MODULE_AUTHOR("Andres Salomon <dilinger at collabora.co.uk>");
+MODULE_DESCRIPTION("AMD CS5535/CS5536 GPIO driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/cs5535.h b/include/linux/cs5535.h
new file mode 100644
index 0000000..cfea689
--- /dev/null
+++ b/include/linux/cs5535.h
@@ -0,0 +1,58 @@
+/*
+ * AMD CS5535/CS5536 definitions
+ * Copyright (C) 2006 Advanced Micro Devices, Inc.
+ * Copyright (C) 2009 Andres Salomon <dilinger at collabora.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#ifndef _CS5535_H
+#define _CS5535_H
+
+/* MSRs */
+#define MSR_LBAR_SMB 0x5140000B
+#define MSR_LBAR_GPIO 0x5140000C
+#define MSR_LBAR_MFGPT 0x5140000D
+#define MSR_LBAR_ACPI 0x5140000E
+#define MSR_LBAR_PMS 0x5140000F
+
+/* resource sizes */
+#define LBAR_GPIO_SIZE 0xFF
+#define LBAR_MFGPT_SIZE 0x40
+#define LBAR_ACPI_SIZE 0x40
+#define LBAR_PMS_SIZE 0x80
+
+/* GPIOs */
+#define GPIO_OUTPUT_VAL 0x00
+#define GPIO_OUTPUT_ENABLE 0x04
+#define GPIO_OUTPUT_OPEN_DRAIN 0x08
+#define GPIO_OUTPUT_INVERT 0x0C
+#define GPIO_OUTPUT_AUX1 0x10
+#define GPIO_OUTPUT_AUX2 0x14
+#define GPIO_PULL_UP 0x18
+#define GPIO_PULL_DOWN 0x1C
+#define GPIO_INPUT_ENABLE 0x20
+#define GPIO_INPUT_INVERT 0x24
+#define GPIO_INPUT_FILTER 0x28
+#define GPIO_INPUT_EVENT_COUNT 0x2C
+#define GPIO_READ_BACK 0x30
+#define GPIO_INPUT_AUX1 0x34
+#define GPIO_EVENTS_ENABLE 0x38
+#define GPIO_LOCK_ENABLE 0x3C
+#define GPIO_POSITIVE_EDGE_EN 0x40
+#define GPIO_NEGATIVE_EDGE_EN 0x44
+#define GPIO_POSITIVE_EDGE_STS 0x48
+#define GPIO_NEGATIVE_EDGE_STS 0x4C
+
+#define GPIO_MAP_X 0xE0
+#define GPIO_MAP_Y 0xE4
+#define GPIO_MAP_Z 0xE8
+#define GPIO_MAP_W 0xEC
+
+void cs5535_gpio_set(unsigned offset, unsigned int reg);
+void cs5535_gpio_clear(unsigned offset, unsigned int reg);
+int cs5535_gpio_isset(unsigned offset, unsigned int reg);
+
+#endif
--
1.5.6.5
More information about the Linux-geode
mailing list