[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.16.0-rc3-6.g005d1b3-default (geeko@buildhost) (gcc version 7.3.0 (SUSE Linux)) #1 SMP Sun Mar 4 10:10:16 UTC 2018 (005d1b3) [ 0.000000] Machine model: Raspberry Pi 3 Model B [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: EFI v2.05 by Das U-boot [ 0.000000] efi: SMBIOS=0x35b0e000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x0000000036ffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x36fdf300-0x36fe0dff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x0000000036ffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000000000fff] [ 0.000000] node 0: [mem 0x0000000000001000-0x0000000035b0dfff] [ 0.000000] node 0: [mem 0x0000000035b0e000-0x0000000035b0efff] [ 0.000000] node 0: [mem 0x0000000035b0f000-0x0000000036f86fff] [ 0.000000] node 0: [mem 0x0000000036f87000-0x0000000036f87fff] [ 0.000000] node 0: [mem 0x0000000036f88000-0x0000000036ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000036ffffff] [ 0.000000] On node 0 totalpages: 225280 [ 0.000000] DMA32 zone: 3520 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 225280 pages, LIFO batch:31 [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 25 pages/cpu @ (ptrval) s65048 r8192 d29160 u102400 [ 0.000000] pcpu-alloc: s65048 r8192 d29160 u102400 alloc=25*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 221760 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/Image-4.16.0-rc3-6.g005d1b3-default root=UUID=e70a1a15-cf94-46da-9a9c-5cb5abc296ad root=/dev/disk/by-id/mmc-00000_0x55353082-part2 disk=/dev/disk/by-id/mmc-00000_0x55353082 resume=/dev/disk/by-id/mmc-00000_0x55353082-part3 quiet splash=silent plymouth.enable=0 console=ttyS0,115200n8 console=tty quiet [ 0.000000] Memory: 844284K/901120K available (9404K kernel code, 1642K rwdata, 4168K rodata, 5248K init, 1031K bss, 56836K reserved, 0K cma-reserved) [ 0.000000] ftrace: allocating 35374 entries in 139 pages [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] arch_timer: WARNING: Invalid trigger for IRQ75, assuming level low [ 0.000000] arch_timer: WARNING: Please fix your firmware [ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000528] Console: colour dummy device 80x25 [ 0.000550] console [tty0] enabled [ 0.000647] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000664] pid_max: default: 32768 minimum: 301 [ 0.000876] Security Framework initialized [ 0.001000] AppArmor: AppArmor initialized [ 0.002588] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.003281] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.003368] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.003401] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.005538] ASID allocator initialised with 32768 entries [ 0.005688] Hierarchical SRCU implementation. [ 0.009053] Remapping and enabling EFI services. [ 0.009116] EFI remap 0x0000000035b0e000 => (ptrval) [ 0.009126] EFI remap 0x0000000036f87000 => (ptrval) [ 0.009134] EFI remap 0x000000003f100000 => (ptrval) [ 0.009733] smp: Bringing up secondary CPUs ... [ 0.010846] Detected VIPT I-cache on CPU1 [ 0.010911] arch_timer: WARNING: Invalid trigger for IRQ75, assuming level low [ 0.010914] arch_timer: WARNING: Please fix your firmware [ 0.010930] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.012168] Detected VIPT I-cache on CPU2 [ 0.012214] arch_timer: WARNING: Invalid trigger for IRQ75, assuming level low [ 0.012217] arch_timer: WARNING: Please fix your firmware [ 0.012229] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.013385] Detected VIPT I-cache on CPU3 [ 0.013421] arch_timer: WARNING: Invalid trigger for IRQ75, assuming level low [ 0.013424] arch_timer: WARNING: Please fix your firmware [ 0.013435] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.013643] smp: Brought up 1 node, 4 CPUs [ 0.013652] SMP: Total of 4 processors activated. [ 0.013661] CPU features: detected feature: 32-bit EL0 Support [ 0.013668] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.019389] CPU: All CPU(s) started at EL2 [ 0.019418] alternatives: patching kernel code [ 0.021061] devtmpfs: initialized [ 0.028700] evm: security.selinux [ 0.028710] evm: security.apparmor [ 0.028715] evm: security.ima [ 0.028721] evm: security.capability [ 0.029302] Registered cp15_barrier emulation handler [ 0.029321] Registered setend emulation handler [ 0.029875] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.029966] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.030430] pinctrl core: initialized pinctrl subsystem [ 0.031873] SMBIOS 3.0 present. [ 0.031894] DMI: raspberrypi rpi/rpi, BIOS 2017.05 05/08/2017 [ 0.032741] NET: Registered protocol family 16 [ 0.035560] audit: initializing netlink subsys (disabled) [ 0.035814] audit: type=2000 audit(0.030:1): state=initialized audit_enabled=0 res=1 [ 0.037373] cpuidle: using governor ladder [ 0.037557] cpuidle: using governor menu [ 0.038012] vdso: 2 pages (1 code @ 00000000bc8db256, 1 data @ 00000000238b0543) [ 0.038034] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.038562] DMA: preallocated 256 KiB pool for atomic allocations [ 0.039381] Serial: AMBA PL011 UART driver [ 0.044609] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_ctsrts_gpio32, deferring probe [ 0.063474] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.065311] ACPI: Interpreter disabled. [ 0.066207] vgaarb: loaded [ 0.066922] SCSI subsystem initialized [ 0.067185] libata version 3.00 loaded. [ 0.067753] EDAC MC: Ver: 3.0.0 [ 0.067954] EDAC DEBUG: edac_mc_sysfs_init: device mc created [ 0.068375] Registered efivars operations [ 0.068404] efivars: get_next_variable: status=8000000000000007 [ 0.069788] NetLabel: Initializing [ 0.069795] NetLabel: domain hash size = 128 [ 0.069801] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.069926] NetLabel: unlabeled traffic allowed by default [ 0.070560] clocksource: Switched to clocksource arch_sys_counter [ 0.173668] VFS: Disk quotas dquot_6.6.0 [ 0.173796] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.174666] AppArmor: AppArmor Filesystem Enabled [ 0.174769] pnp: PnP ACPI: disabled [ 0.187310] NET: Registered protocol family 2 [ 0.188138] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes) [ 0.188213] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.188385] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 0.188592] TCP: Hash tables configured (established 8192 bind 8192) [ 0.188875] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.188935] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.189282] NET: Registered protocol family 1 [ 0.189323] PCI: CLS 0 bytes, default 128 [ 0.189824] Unpacking initramfs... [ 9.062128] Freeing initrd memory: 16252K [ 9.063128] kvm [1]: 8-bit VMID [ 9.063137] kvm [1]: IDMAP page: 9a4000 [ 9.063144] kvm [1]: HYP VA range: 800000000000:ffffffffffff [ 9.064354] kvm [1]: Invalid trigger for IRQ76, assuming level low [ 9.064418] kvm [1]: virtual timer IRQ76 [ 9.064594] kvm [1]: Hyp mode initialized successfully [ 9.067299] Initialise system trusted keyrings [ 9.067574] workingset: timestamp_bits=44 max_order=18 bucket_order=0 [ 9.067848] zbud: loaded [ 9.076403] Key type asymmetric registered [ 9.076417] Asymmetric key parser 'x509' registered [ 9.076601] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 9.076799] io scheduler noop registered [ 9.076807] io scheduler deadline registered [ 9.076901] io scheduler cfq registered (default) [ 9.076909] io scheduler kyber registered [ 9.076956] io scheduler bfq registered [ 9.085523] efifb: probing for efifb [ 9.085726] efifb: framebuffer at 0x3d513000, using 7012k, total 7011k [ 9.085735] efifb: mode is 1824x984x32, linelength=7296, pages=1 [ 9.085740] efifb: scrolling: redraw [ 9.085750] efifb: Truecolor: size=8:8:8:8, shift=24:0:8:16 [ 9.129154] Console: switching to colour frame buffer device 228x61 [ 9.171661] fb0: EFI VGA frame buffer device [ 9.181531] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 9.184389] console [ttyS0] disabled [ 9.184439] 3f215040.serial: ttyS0 at MMIO 0x0 (irq = 61, base_baud = 31249999) is a 16550 [ 9.190836] console [ttyS0] enabled [ 9.191987] Serial: AMBA driver [ 9.192584] msm_serial: driver initialized [ 9.194032] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 9.195127] libphy: Fixed MDIO Bus: probed [ 9.195753] mousedev: PS/2 mouse device common for all mice [ 9.198724] ledtrig-cpu: registered to indicate activity on CPUs [ 9.199069] EFI Variables Facility v0.08 2004-May-17 [ 9.199096] efivars: get_next_variable: status=8000000000000007 [ 9.199199] hidraw: raw HID events driver (C) Jiri Kosina [ 9.199575] bcm2835-mbox 3f00b880.mailbox: mailbox enabled [ 9.201882] NET: Registered protocol family 10 [ 9.227523] Segment Routing with IPv6 [ 9.228961] registered taskstats version 1 [ 9.228985] Loading compiled-in X.509 certificates [ 9.242732] Loaded X.509 cert 'home:michals OBS Project: 544f3f8a786dbbef2bc5f439f86f094f2347e991' [ 9.242883] zswap: loaded using pool lzo/zbud [ 9.266738] Key type big_key registered [ 9.278414] Key type encrypted registered [ 9.278437] AppArmor: AppArmor sha1 policy hashing enabled [ 9.278452] ima: No TPM chip found, activating TPM-bypass! (rc=-19) [ 9.278605] evm: HMAC attrs: 0x1 [ 9.284131] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 66, base_baud = 0) is a PL011 rev2 [ 9.286607] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-09-02 11:49 [ 9.288723] hctosys: unable to open rtc device (rtc0) [ 9.315948] Freeing unused kernel memory: 5248K [ 9.345959] efivars: get_next_variable: status=8000000000000007 [ 9.355500] systemd[1]: systemd 228 running in system mode. (+PAM -AUDIT +SELINUX -IMA +APPARMOR -SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT -GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 9.356743] systemd[1]: Detected architecture arm64. [ 9.356763] systemd[1]: Running in initial RAM disk. [ 9.356917] systemd[1]: Set hostname to . [ 9.638640] systemd[1]: Reached target Timers. [ 9.642236] systemd[1]: Created slice System Slice. [ 9.642504] systemd[1]: Listening on udev Kernel Socket. [ 9.643411] systemd[1]: Created slice system-systemd\x2dhibernate\x2dresume.slice. [ 9.643693] systemd[1]: Listening on Journal Socket (/dev/log). [ 9.643973] systemd[1]: Listening on udev Control Socket. [ 10.483945] sdhost-bcm2835 3f202000.sdhost: unable to initialise DMA channel. Falling back to PIO [ 10.498917] sdhci: Secure Digital Host Controller Interface driver [ 10.498931] sdhci: Copyright(c) Pierre Ossman [ 10.504426] sdhci-pltfm: SDHCI platform and OF driver helper [ 10.586429] sdhost-bcm2835 3f202000.sdhost: loaded - DMA disabled [ 10.587211] sdhost-bcm2835 3f202000.sdhost: resetting [ 10.618898] mmc1: SDHCI controller on 3f300000.sdhci [3f300000.sdhci] using PIO [ 10.643482] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 10.645234] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 10.646980] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 10.650113] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 10.694224] mmc0: host does not support reading read-only switch, assuming write-enable [ 10.695999] mmc0: new high speed SDHC card at address 0001 [ 10.710758] mmcblk0: mmc0:0001 00000 14.6 GiB [ 10.715732] mmcblk0: p1 p2 p3 [ 10.805776] mmc1: new high speed SDIO card at address 0001 [ 10.866739] usbcore: registered new interface driver usbfs [ 10.866834] usbcore: registered new interface driver hub [ 10.867021] usbcore: registered new device driver usb [ 10.988211] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 10.989936] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 10.990224] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 10.990238] cfg80211: failed to load regulatory.db [ 11.123585] PM: Starting manual resume from disk [ 11.124345] PM: Image not found (code -22) [ 11.335132] random: crng init done [ 11.359854] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 12.100186] systemd-journald[157]: Received SIGTERM from PID 1 (systemd). [ 12.238771] systemd: 16 output lines suppressed due to ratelimiting [ 13.595204] EXT4-fs (mmcblk0p2): re-mounted. Opts: nobarrier [ 13.892099] systemd-journald[363]: Received request to flush runtime journal from PID 1 [ 15.397135] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer [ 16.413335] bcm2835-rng 3f104000.rng: hwrng registered [ 16.416059] i2c-bcm2835 3f805000.i2c: Could not read clock-frequency property [ 16.417899] dwc2 3f980000.usb: 3f980000.usb supply vusb_d not found, using dummy regulator [ 16.418029] dwc2 3f980000.usb: 3f980000.usb supply vusb_a not found, using dummy regulator [ 16.484647] Adding 505172k swap on /dev/mmcblk0p3. Priority:-2 extents:1 across:505172k SSFS [ 16.633867] brcmfmac: probe of mmc1:0001:1 failed with error -110 [ 16.634398] brcmfmac: probe of mmc1:0001:2 failed with error -110 [ 16.634626] usbcore: registered new interface driver brcmfmac [ 16.716968] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 16.920804] dwc2 3f980000.usb: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024 [ 16.920872] dwc2 3f980000.usb: EPs: 8, dedicated fifos, 4080 entries in SPRAM [ 16.921404] dwc2 3f980000.usb: DWC OTG Controller [ 16.921443] dwc2 3f980000.usb: new USB bus registered, assigned bus number 1 [ 16.921500] dwc2 3f980000.usb: irq 41, io mem 0x3f980000 [ 16.921979] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.921993] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.922003] usb usb1: Product: DWC OTG Controller [ 16.922013] usb usb1: Manufacturer: Linux 4.16.0-rc3-6.g005d1b3-default dwc2_hsotg [ 16.922023] usb usb1: SerialNumber: 3f980000.usb [ 16.924951] hub 1-0:1.0: USB hub found [ 16.925579] hub 1-0:1.0: 1 port detected [ 17.163362] rc_core: IR Remote Control driver registered, major 239 [ 17.370705] usb 1-1: new high-speed USB device number 2 using dwc2 [ 17.640963] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 17.640980] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 17.641982] hub 1-1:1.0: USB hub found [ 17.642079] hub 1-1:1.0: 5 ports detected [ 17.930635] Registered IR keymap rc-cec [ 17.930977] rc rc0: RC for vc4 as /devices/platform/soc/3f902000.hdmi/rc/rc0 [ 17.931295] input: RC for vc4 as /devices/platform/soc/3f902000.hdmi/rc/rc0/input0 [ 17.932069] vc4_hdmi 3f902000.hdmi: 'dmas' DT property is missing, no HDMI audio [ 17.932233] vc4-drm soc:gpu: bound 3f902000.hdmi (ops vc4_hdmi_ops [vc4]) [ 17.932606] vc4-drm soc:gpu: bound 3f400000.hvs (ops vc4_hvs_ops [vc4]) [ 17.933015] vc4-drm soc:gpu: bound 3f206000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 17.933313] vc4-drm soc:gpu: bound 3f207000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 17.933615] vc4-drm soc:gpu: bound 3f807000.pixelvalve (ops vc4_crtc_ops [vc4]) [ 17.933730] vc4-drm soc:gpu: swiotlb: coherent allocation failed, size=16777216 [ 17.933747] CPU: 2 PID: 460 Comm: systemd-udevd Not tainted 4.16.0-rc3-6.g005d1b3-default #1 [ 17.933752] Hardware name: raspberrypi rpi/rpi, BIOS 2017.05 05/08/2017 [ 17.933759] Call trace: [ 17.933779] dump_backtrace+0x0/0x1d0 [ 17.933788] show_stack+0x24/0x30 [ 17.933800] dump_stack+0xbc/0xf8 [ 17.933811] swiotlb_alloc_buffer+0x174/0x178 [ 17.933818] swiotlb_alloc+0x64/0x78 [ 17.933829] __dma_alloc+0xe0/0x1d8 [ 17.934156] drm_gem_cma_create+0xa8/0x198 [drm] [ 17.934242] vc4_bo_create+0x134/0x4e0 [vc4] [ 17.934329] vc4_allocate_bin_bo+0x78/0x128 [vc4] [ 17.934416] vc4_v3d_bind+0x100/0x278 [vc4] [ 17.934432] component_bind_all+0x108/0x2c8 [ 17.934518] vc4_drm_bind+0xac/0x188 [vc4] [ 17.934529] try_to_bring_up_master+0x214/0x300 [ 17.934539] component_master_add_with_match+0xcc/0x120 [ 17.934624] vc4_platform_drm_probe+0xc8/0x108 [vc4] [ 17.934636] platform_drv_probe+0x60/0xc0 [ 17.934645] driver_probe_device+0x334/0x498 [ 17.934653] __driver_attach+0x124/0x128 [ 17.934661] bus_for_each_dev+0x70/0xa8 [ 17.934668] driver_attach+0x30/0x40 [ 17.934676] bus_add_driver+0x240/0x2b8 [ 17.934684] driver_register+0x6c/0x118 [ 17.934692] __platform_driver_register+0x54/0x60 [ 17.934780] vc4_drm_register+0x40/0x68 [vc4] [ 17.934789] do_one_initcall+0x58/0x168 [ 17.934802] do_init_module+0x64/0x1dc [ 17.934811] load_module+0x14c8/0x1678 [ 17.934820] SyS_finit_module+0xd8/0xf0 [ 17.934827] el0_svc_naked+0x30/0x34 [ 17.934887] vc4-drm soc:gpu: swiotlb: coherent allocation failed, size=16777216 [ 17.934899] CPU: 2 PID: 460 Comm: systemd-udevd Not tainted 4.16.0-rc3-6.g005d1b3-default #1 [ 17.934904] Hardware name: raspberrypi rpi/rpi, BIOS 2017.05 05/08/2017 [ 17.934907] Call trace: [ 17.934919] dump_backtrace+0x0/0x1d0 [ 17.934925] show_stack+0x24/0x30 [ 17.934937] dump_stack+0xbc/0xf8 [ 17.934946] swiotlb_alloc_buffer+0x174/0x178 [ 17.934953] swiotlb_alloc+0x64/0x78 [ 17.934962] __dma_alloc+0xe0/0x1d8 [ 17.935247] drm_gem_cma_create+0xa8/0x198 [drm] [ 17.935332] vc4_bo_create+0x1a4/0x4e0 [vc4] [ 17.935419] vc4_allocate_bin_bo+0x78/0x128 [vc4] [ 17.935506] vc4_v3d_bind+0x100/0x278 [vc4] [ 17.935516] component_bind_all+0x108/0x2c8 [ 17.935602] vc4_drm_bind+0xac/0x188 [vc4] [ 17.935612] try_to_bring_up_master+0x214/0x300 [ 17.935622] component_master_add_with_match+0xcc/0x120 [ 17.935708] vc4_platform_drm_probe+0xc8/0x108 [vc4] [ 17.935718] platform_drv_probe+0x60/0xc0 [ 17.935726] driver_probe_device+0x334/0x498 [ 17.935734] __driver_attach+0x124/0x128 [ 17.935741] bus_for_each_dev+0x70/0xa8 [ 17.935749] driver_attach+0x30/0x40 [ 17.935756] bus_add_driver+0x240/0x2b8 [ 17.935764] driver_register+0x6c/0x118 [ 17.935773] __platform_driver_register+0x54/0x60 [ 17.935860] vc4_drm_register+0x40/0x68 [vc4] [ 17.935867] do_one_initcall+0x58/0x168 [ 17.935879] do_init_module+0x64/0x1dc [ 17.935888] load_module+0x14c8/0x1678 [ 17.935897] SyS_finit_module+0xd8/0xf0 [ 17.935904] el0_svc_naked+0x30/0x34 [ 17.935943] vc4-drm soc:gpu: swiotlb: coherent allocation failed, size=16777216 [ 17.935954] CPU: 2 PID: 460 Comm: systemd-udevd Not tainted 4.16.0-rc3-6.g005d1b3-default #1 [ 17.935958] Hardware name: raspberrypi rpi/rpi, BIOS 2017.05 05/08/2017 [ 17.935963] Call trace: [ 17.935973] dump_backtrace+0x0/0x1d0 [ 17.935979] show_stack+0x24/0x30 [ 17.935987] dump_stack+0xbc/0xf8 [ 17.935995] swiotlb_alloc_buffer+0x174/0x178 [ 17.936001] swiotlb_alloc+0x64/0x78 [ 17.936011] __dma_alloc+0xe0/0x1d8 [ 17.936271] drm_gem_cma_create+0xa8/0x198 [drm] [ 17.936356] vc4_bo_create+0x36c/0x4e0 [vc4] [ 17.936443] vc4_allocate_bin_bo+0x78/0x128 [vc4] [ 17.936531] vc4_v3d_bind+0x100/0x278 [vc4] [ 17.936541] component_bind_all+0x108/0x2c8 [ 17.936629] vc4_drm_bind+0xac/0x188 [vc4] [ 17.936639] try_to_bring_up_master+0x214/0x300 [ 17.936648] component_master_add_with_match+0xcc/0x120 [ 17.936735] vc4_platform_drm_probe+0xc8/0x108 [vc4] [ 17.936745] platform_drv_probe+0x60/0xc0 [ 17.936754] driver_probe_device+0x334/0x498 [ 17.936761] __driver_attach+0x124/0x128 [ 17.936770] bus_for_each_dev+0x70/0xa8 [ 17.936777] driver_attach+0x30/0x40 [ 17.936784] bus_add_driver+0x240/0x2b8 [ 17.936792] driver_register+0x6c/0x118 [ 17.936801] __platform_driver_register+0x54/0x60 [ 17.936889] vc4_drm_register+0x40/0x68 [vc4] [ 17.936897] do_one_initcall+0x58/0x168 [ 17.936908] do_init_module+0x64/0x1dc [ 17.936917] load_module+0x14c8/0x1678 [ 17.936926] SyS_finit_module+0xd8/0xf0 [ 17.936933] el0_svc_naked+0x30/0x34 [ 17.937033] [drm:vc4_bo_create [vc4]] *ERROR* Failed to allocate from CMA: [ 17.944470] vc4_v3d 3fc00000.v3d: Failed to allocate memory for tile binning: -12. You may need to enable CMA or give it more memory. [ 17.957408] vc4-drm soc:gpu: failed to bind 3fc00000.v3d (ops vc4_v3d_ops [vc4]): -12 [ 18.020719] usb 1-1.1: new high-speed USB device number 3 using dwc2 [ 18.081881] vc4-drm soc:gpu: master bind failed: -12 [ 18.081938] vc4-drm: probe of soc:gpu failed with error -12 [ 18.171767] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 18.171784] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 18.300755] usb 1-1.4: new low-speed USB device number 4 using dwc2 [ 18.595642] smsc95xx v1.0.6 [ 18.787944] usb 1-1.4: New USB device found, idVendor=0b38, idProduct=0003 [ 18.787964] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 18.787974] usb 1-1.4: Product: USB-compliant keyboard [ 18.844022] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:69:dc:65 [ 18.844415] usbcore: registered new interface driver smsc95xx [ 19.549884] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.550277] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.706690] usbcore: registered new interface driver usbhid [ 19.706703] usbhid: USB HID core driver [ 19.724124] input: USB-compliant keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:0B38:0003.0001/input/input1 [ 19.792063] hid-generic 0003:0B38:0003.0001: input,hidraw0: USB HID v1.10 Keyboard [USB-compliant keyboard] on usb-3f980000.usb-1.4/input0 [ 19.795138] input: USB-compliant keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.1/0003:0B38:0003.0002/input/input2 [ 19.863347] hid-generic 0003:0B38:0003.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [USB-compliant keyboard] on usb-3f980000.usb-1.4/input1 [ 21.009199] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 21.011461] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 21.136118] NET: Registered protocol family 17 <3>[ 731.358420] sdhost-bcm2835 3f202000.sdhost: timeout waiting for hardware interrupt. <6>[ 731.366507] sdhost-bcm2835 3f202000.sdhost: resetting <3>[ 741.598499] sdhost-bcm2835 3f202000.sdhost: timeout waiting for hardware interrupt. <6>[ 741.606583] sdhost-bcm2835 3f202000.sdhost: resetting <3>[ 744.688543] mmc0: Card stuck in wrong state! mmcblk0 card_busy_detect status: 0xe00 <3>[ 799.198941] sdhost-bcm2835 3f202000.sdhost: timeout waiting for hardware interrupt. <6>[ 799.207027] sdhost-bcm2835 3f202000.sdhost: resetting <3>[ 809.439021] sdhost-bcm2835 3f202000.sdhost: timeout waiting for hardware interrupt. <6>[ 809.447109] sdhost-bcm2835 3f202000.sdhost: resetting <3>[ 812.529050] mmc0: Card stuck in wrong state! mmcblk0 card_busy_detect status: 0xe00