The pm-mmp2 and pm-pxa910 power management related irq_set_wake callbacks fiddle pointlessly with the irq actions for no reason except for lack of understanding how the wakeup mechanism works. On supsend the core disables all interrupts lazily, i.e. it does not mask them at the irq controller level. So any interrupt which is firing during supsend will mark the corresponding interrupt line as pending. Just before the core powers down it checks whether there are interrupts pending from interrupt lines which are marked as wakeup sources and if so it aborts the resume and resends the interrupts. The IRQF_NO_SUSPEND flag for interrupt actions is a totally different mechanism. That allows the device driver to prevent the core from disabling the interrupt despite the fact that it is not marked as a wakeup source. This has nothing to do with the case at hand. It was introduced for special cases where lazy disable is not possible. Remove the nonsense along with the braindamaged boundary check. The core code does NOT call these functions out of boundary. Add a FIXME comment to an unhandled error path which merily printks some useless blurb instead of returning a proper error code. Signed-off-by: Thomas Gleixner Cc: arm Cc: Eric Miao Cc: Haojian Zhuang Cc: Russell King --- arch/arm/mach-mmp/pm-mmp2.c | 16 +--------------- arch/arm/mach-mmp/pm-pxa910.c | 20 ++++---------------- 2 files changed, 5 insertions(+), 31 deletions(-) Index: tip/arch/arm/mach-mmp/pm-mmp2.c =================================================================== --- tip.orig/arch/arm/mach-mmp/pm-mmp2.c +++ tip/arch/arm/mach-mmp/pm-mmp2.c @@ -27,22 +27,8 @@ int mmp2_set_wake(struct irq_data *d, unsigned int on) { - int irq = d->irq; - struct irq_desc *desc = irq_to_desc(irq); unsigned long data = 0; - - if (unlikely(irq >= nr_irqs)) { - pr_err("IRQ nubmers are out of boundary!\n"); - return -EINVAL; - } - - if (on) { - if (desc->action) - desc->action->flags |= IRQF_NO_SUSPEND; - } else { - if (desc->action) - desc->action->flags &= ~IRQF_NO_SUSPEND; - } + int irq = d->irq; /* enable wakeup sources */ switch (irq) { Index: tip/arch/arm/mach-mmp/pm-pxa910.c =================================================================== --- tip.orig/arch/arm/mach-mmp/pm-pxa910.c +++ tip/arch/arm/mach-mmp/pm-pxa910.c @@ -27,22 +27,8 @@ int pxa910_set_wake(struct irq_data *data, unsigned int on) { - int irq = data->irq; - struct irq_desc *desc = irq_to_desc(data->irq); uint32_t awucrm = 0, apcr = 0; - - if (unlikely(irq >= nr_irqs)) { - pr_err("IRQ nubmers are out of boundary!\n"); - return -EINVAL; - } - - if (on) { - if (desc->action) - desc->action->flags |= IRQF_NO_SUSPEND; - } else { - if (desc->action) - desc->action->flags &= ~IRQF_NO_SUSPEND; - } + int irq = data->irq; /* setting wakeup sources */ switch (irq) { @@ -115,9 +101,11 @@ int pxa910_set_wake(struct irq_data *dat if (irq >= IRQ_GPIO_START && irq < IRQ_BOARD_START) { awucrm = MPMU_AWUCRM_WAKEUP(2); apcr |= MPMU_APCR_SLPWP2; - } else + } else { + /* FIXME: This should return a proper error code ! */ printk(KERN_ERR "Error: no defined wake up source irq: %d\n", irq); + } } if (on) {