The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things so it makes sense to create a common file for both devices and a specific file for each. No functionnal change except dropping uart 1 & 2. Signed-off-by: Arnaud Patard Index: linux-2.6-submit/arch/arm/mach-mx5/board-mx51_efikamx.c =================================================================== --- linux-2.6-submit.orig/arch/arm/mach-mx5/board-mx51_efikamx.c 2011-02-01 12:26:39.000000000 +0100 +++ linux-2.6-submit/arch/arm/mach-mx5/board-mx51_efikamx.c 2011-02-02 09:10:36.000000000 +0100 @@ -40,8 +40,7 @@ #include "devices-imx51.h" #include "devices.h" - -#define MX51_USB_PLL_DIV_24_MHZ 0x01 +#include "efika.h" #define EFIKAMX_PCBID0 IMX_GPIO_NR(3, 16) #define EFIKAMX_PCBID1 IMX_GPIO_NR(3, 17) @@ -53,9 +52,6 @@ #define EFIKAMX_POWER_KEY IMX_GPIO_NR(2, 31) -#define EFIKAMX_SPI_CS0 IMX_GPIO_NR(4, 24) -#define EFIKAMX_SPI_CS1 IMX_GPIO_NR(4, 25) - /* board 1.1 doesn't have same reset gpio */ #define EFIKAMX_RESET1_1 IMX_GPIO_NR(3, 2) #define EFIKAMX_RESET IMX_GPIO_NR(1, 4) @@ -67,38 +63,11 @@ #define MX51_PAD_PWRKEY IOMUX_PAD(0x48c, 0x0f8, 1, 0x0, 0, PAD_CTL_PUS_100K_UP | PAD_CTL_PKE) static iomux_v3_cfg_t mx51efikamx_pads[] = { - /* UART1 */ - MX51_PAD_UART1_RXD__UART1_RXD, - MX51_PAD_UART1_TXD__UART1_TXD, - MX51_PAD_UART1_RTS__UART1_RTS, - MX51_PAD_UART1_CTS__UART1_CTS, /* board id */ MX51_PAD_PCBID0, MX51_PAD_PCBID1, MX51_PAD_PCBID2, - /* SD 1 */ - MX51_PAD_SD1_CMD__SD1_CMD, - MX51_PAD_SD1_CLK__SD1_CLK, - MX51_PAD_SD1_DATA0__SD1_DATA0, - MX51_PAD_SD1_DATA1__SD1_DATA1, - MX51_PAD_SD1_DATA2__SD1_DATA2, - MX51_PAD_SD1_DATA3__SD1_DATA3, - - /* SD 2 */ - MX51_PAD_SD2_CMD__SD2_CMD, - MX51_PAD_SD2_CLK__SD2_CLK, - MX51_PAD_SD2_DATA0__SD2_DATA0, - MX51_PAD_SD2_DATA1__SD2_DATA1, - MX51_PAD_SD2_DATA2__SD2_DATA2, - MX51_PAD_SD2_DATA3__SD2_DATA3, - - /* SD/MMC WP/CD */ - MX51_PAD_GPIO1_0__SD1_CD, - MX51_PAD_GPIO1_1__SD1_WP, - MX51_PAD_GPIO1_7__SD2_WP, - MX51_PAD_GPIO1_8__SD2_CD, - /* leds */ MX51_PAD_CSI1_D9__GPIO3_13, MX51_PAD_CSI1_VSYNC__GPIO3_14, @@ -107,53 +76,11 @@ /* power key */ MX51_PAD_PWRKEY, - /* spi */ - MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, - MX51_PAD_CSPI1_MISO__ECSPI1_MISO, - MX51_PAD_CSPI1_SS0__GPIO4_24, - MX51_PAD_CSPI1_SS1__GPIO4_25, - MX51_PAD_CSPI1_RDY__ECSPI1_RDY, - MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, - /* reset */ MX51_PAD_DI1_PIN13__GPIO3_2, MX51_PAD_GPIO1_4__GPIO1_4, }; -/* Serial ports */ -static const struct imxuart_platform_data uart_pdata = { - .flags = IMXUART_HAVE_RTSCTS, -}; - -/* This function is board specific as the bit mask for the plldiv will also - * be different for other Freescale SoCs, thus a common bitmask is not - * possible and cannot get place in /plat-mxc/ehci.c. - */ -static int initialize_otg_port(struct platform_device *pdev) -{ - u32 v; - void __iomem *usb_base; - void __iomem *usbother_base; - usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K); - if (!usb_base) - return -ENOMEM; - usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET); - - /* Set the PHY clock to 19.2MHz */ - v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET); - v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK; - v |= MX51_USB_PLL_DIV_24_MHZ; - __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET); - iounmap(usb_base); - return 0; -} - -static struct mxc_usbh_platform_data dr_utmi_config = { - .init = initialize_otg_port, - .portsc = MXC_EHCI_UTMI_16BIT, - .flags = MXC_EHCI_INTERNAL_PHY, -}; - /* PCBID2 PCBID1 PCBID0 STATE 1 1 1 ER1:rev1.1 1 1 0 ER2:rev1.2 @@ -252,47 +179,6 @@ .nbuttons = ARRAY_SIZE(mx51_efikamx_powerkey), }; -static struct mtd_partition mx51_efikamx_spi_nor_partitions[] = { - { - .name = "u-boot", - .offset = 0, - .size = SZ_256K, - }, - { - .name = "config", - .offset = MTDPART_OFS_APPEND, - .size = SZ_64K, - }, -}; - -static struct flash_platform_data mx51_efikamx_spi_flash_data = { - .name = "spi_flash", - .parts = mx51_efikamx_spi_nor_partitions, - .nr_parts = ARRAY_SIZE(mx51_efikamx_spi_nor_partitions), - .type = "sst25vf032b", -}; - -static struct spi_board_info mx51_efikamx_spi_board_info[] __initdata = { - { - .modalias = "m25p80", - .max_speed_hz = 25000000, - .bus_num = 0, - .chip_select = 1, - .platform_data = &mx51_efikamx_spi_flash_data, - .irq = -1, - }, -}; - -static int mx51_efikamx_spi_cs[] = { - EFIKAMX_SPI_CS0, - EFIKAMX_SPI_CS1, -}; - -static const struct spi_imx_master mx51_efikamx_spi_pdata __initconst = { - .chipselect = mx51_efikamx_spi_cs, - .num_chipselect = ARRAY_SIZE(mx51_efikamx_spi_cs), -}; - void mx51_efikamx_reset(void) { if (system_rev == 0x11) @@ -305,12 +191,9 @@ { mxc_iomux_v3_setup_multiple_pads(mx51efikamx_pads, ARRAY_SIZE(mx51efikamx_pads)); + efika_board_common_init(); + mx51_efikamx_board_id(); - mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config); - imx51_add_imx_uart(0, &uart_pdata); - imx51_add_imx_uart(1, &uart_pdata); - imx51_add_imx_uart(2, &uart_pdata); - imx51_add_sdhci_esdhc_imx(0, NULL); /* on < 1.2 boards both SD controllers are used */ if (system_rev < 0x12) { @@ -321,10 +204,6 @@ platform_device_register(&mx51_efikamx_leds_device); imx51_add_gpio_keys(&mx51_efikamx_powerkey_data); - spi_register_board_info(mx51_efikamx_spi_board_info, - ARRAY_SIZE(mx51_efikamx_spi_board_info)); - imx51_add_ecspi(0, &mx51_efikamx_spi_pdata); - if (system_rev == 0x11) { gpio_request(EFIKAMX_RESET1_1, "reset"); gpio_direction_output(EFIKAMX_RESET1_1, 1); Index: linux-2.6-submit/arch/arm/mach-mx5/efika.h =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ linux-2.6-submit/arch/arm/mach-mx5/efika.h 2011-02-02 09:10:36.000000000 +0100 @@ -0,0 +1,6 @@ +#ifndef _EFIKA_H +#define _EFIKA_H + +void __init efika_board_common_init(void); + +#endif Index: linux-2.6-submit/arch/arm/mach-mx5/Kconfig =================================================================== --- linux-2.6-submit.orig/arch/arm/mach-mx5/Kconfig 2011-02-01 12:26:40.000000000 +0100 +++ linux-2.6-submit/arch/arm/mach-mx5/Kconfig 2011-02-02 09:10:36.000000000 +0100 @@ -113,12 +113,16 @@ endchoice -config MACH_MX51_EFIKAMX - bool "Support MX51 Genesi Efika MX nettop" +config MX51_EFIKA_COMMON + bool select SOC_IMX51 select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX select IMX_HAVE_PLATFORM_SPI_IMX + +config MACH_MX51_EFIKAMX + bool "Support MX51 Genesi Efika MX nettop" + select MX51_EFIKA_COMMON help Include support for Genesi Efika MX nettop. This includes specific configurations for the board and its peripherals. Index: linux-2.6-submit/arch/arm/mach-mx5/Makefile =================================================================== --- linux-2.6-submit.orig/arch/arm/mach-mx5/Makefile 2011-02-01 12:26:39.000000000 +0100 +++ linux-2.6-submit/arch/arm/mach-mx5/Makefile 2011-02-02 09:10:35.000000000 +0100 @@ -16,5 +16,6 @@ obj-$(CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD) += eukrea_mbimx51-baseboard.o obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += board-cpuimx51sd.o obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd-baseboard.o +obj-$(CONFIG_MX51_EFIKA_COMMON) += mx51_efika.o obj-$(CONFIG_MACH_MX51_EFIKAMX) += board-mx51_efikamx.o obj-$(CONFIG_MACH_MX50_RDP) += board-mx50_rdp.o Index: linux-2.6-submit/arch/arm/mach-mx5/mx51_efika.c =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ linux-2.6-submit/arch/arm/mach-mx5/mx51_efika.c 2011-02-02 09:56:00.000000000 +0100 @@ -0,0 +1,186 @@ +/* + * based on code from the following + * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved. + * Copyright 2009-2010 Pegatron Corporation. All Rights Reserved. + * Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include "devices-imx51.h" +#include "devices.h" +#include "efika.h" + +#define MX51_USB_PLL_DIV_24_MHZ 0x01 + +#define EFIKAMX_SPI_CS0 IMX_GPIO_NR(4, 24) +#define EFIKAMX_SPI_CS1 IMX_GPIO_NR(4, 25) + +static iomux_v3_cfg_t mx51efika_pads[] = { + /* UART1 */ + MX51_PAD_UART1_RXD__UART1_RXD, + MX51_PAD_UART1_TXD__UART1_TXD, + MX51_PAD_UART1_RTS__UART1_RTS, + MX51_PAD_UART1_CTS__UART1_CTS, + + /* SD 1 */ + MX51_PAD_SD1_CMD__SD1_CMD, + MX51_PAD_SD1_CLK__SD1_CLK, + MX51_PAD_SD1_DATA0__SD1_DATA0, + MX51_PAD_SD1_DATA1__SD1_DATA1, + MX51_PAD_SD1_DATA2__SD1_DATA2, + MX51_PAD_SD1_DATA3__SD1_DATA3, + + /* SD 2 */ + MX51_PAD_SD2_CMD__SD2_CMD, + MX51_PAD_SD2_CLK__SD2_CLK, + MX51_PAD_SD2_DATA0__SD2_DATA0, + MX51_PAD_SD2_DATA1__SD2_DATA1, + MX51_PAD_SD2_DATA2__SD2_DATA2, + MX51_PAD_SD2_DATA3__SD2_DATA3, + + /* SD/MMC WP/CD */ + MX51_PAD_GPIO1_0__SD1_CD, + MX51_PAD_GPIO1_1__SD1_WP, + MX51_PAD_GPIO1_7__SD2_WP, + MX51_PAD_GPIO1_8__SD2_CD, + + /* spi */ + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, + MX51_PAD_CSPI1_MISO__ECSPI1_MISO, + MX51_PAD_CSPI1_SS0__GPIO4_24, + MX51_PAD_CSPI1_SS1__GPIO4_25, + MX51_PAD_CSPI1_RDY__ECSPI1_RDY, + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, +}; + +/* Serial ports */ +#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE) +static const struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +static inline void mxc_init_imx_uart(void) +{ + imx51_add_imx_uart(0, &uart_pdata); + imx51_add_imx_uart(1, &uart_pdata); + imx51_add_imx_uart(2, &uart_pdata); +} +#else /* !SERIAL_IMX */ +static inline void mxc_init_imx_uart(void) +{ +} +#endif /* SERIAL_IMX */ + +/* This function is board specific as the bit mask for the plldiv will also + * be different for other Freescale SoCs, thus a common bitmask is not + * possible and cannot get place in /plat-mxc/ehci.c. + */ +static int initialize_otg_port(struct platform_device *pdev) +{ + u32 v; + void __iomem *usb_base; + void __iomem *usbother_base; + usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K); + if (!usb_base) + return -ENOMEM; + usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET); + + /* Set the PHY clock to 19.2MHz */ + v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET); + v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK; + v |= MX51_USB_PLL_DIV_24_MHZ; + __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET); + iounmap(usb_base); + return 0; +} + +static struct mxc_usbh_platform_data dr_utmi_config = { + .init = initialize_otg_port, + .portsc = MXC_EHCI_UTMI_16BIT, + .flags = MXC_EHCI_INTERNAL_PHY, +}; + +static struct mtd_partition mx51_efika_spi_nor_partitions[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_256K, + }, + { + .name = "config", + .offset = MTDPART_OFS_APPEND, + .size = SZ_64K, + }, +}; + +static struct flash_platform_data mx51_efika_spi_flash_data = { + .name = "spi_flash", + .parts = mx51_efika_spi_nor_partitions, + .nr_parts = ARRAY_SIZE(mx51_efika_spi_nor_partitions), + .type = "sst25vf032b", +}; + +static struct spi_board_info mx51_efika_spi_board_info[] __initdata = { + { + .modalias = "m25p80", + .max_speed_hz = 25000000, + .bus_num = 0, + .chip_select = 1, + .platform_data = &mx51_efika_spi_flash_data, + .irq = -1, + }, +}; + +static int mx51_efika_spi_cs[] = { + EFIKAMX_SPI_CS0, + EFIKAMX_SPI_CS1, +}; + +static const struct spi_imx_master mx51_efika_spi_pdata __initconst = { + .chipselect = mx51_efika_spi_cs, + .num_chipselect = ARRAY_SIZE(mx51_efika_spi_cs), +}; + +void __init efika_board_common_init(void) +{ + mxc_iomux_v3_setup_multiple_pads(mx51efika_pads, + ARRAY_SIZE(mx51efika_pads)); + mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config); + imx51_add_imx_uart(0, &uart_pdata); + imx51_add_sdhci_esdhc_imx(0, NULL); + + spi_register_board_info(mx51_efika_spi_board_info, + ARRAY_SIZE(mx51_efika_spi_board_info)); + imx51_add_ecspi(0, &mx51_efika_spi_pdata); +} +