The efikamx board is using a gpio to reset the board so add support
for it

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Index: linux-2.6-submit/arch/arm/mach-mx5/board-mx51_efikamx.c
===================================================================
--- linux-2.6-submit.orig/arch/arm/mach-mx5/board-mx51_efikamx.c	2010-10-27 11:43:11.000000000 +0200
+++ linux-2.6-submit/arch/arm/mach-mx5/board-mx51_efikamx.c	2010-10-27 14:36:09.000000000 +0200
@@ -56,6 +56,10 @@
 #define EFIKAMX_SPI_CS0		(3*32 + 24)
 #define EFIKAMX_SPI_CS1		(3*32 + 25)
 
+/* board 1.1 doesn't have same reset gpio */
+#define EFIKAMX_RESET1_1	(2*32 + 2)
+#define EFIKAMX_RESET		(0*32 + 4)
+
 /* the pci ids pin have pull up. they're driven low according to board id */
 #define MX51_PAD_PCBID0	IOMUX_PAD(0x518, 0x130, 3, 0x0,   0, PAD_CTL_PUS_100K_UP)
 #define MX51_PAD_PCBID1	IOMUX_PAD(0x51C, 0x134, 3, 0x0,   0, PAD_CTL_PUS_100K_UP)
@@ -111,6 +115,10 @@
 	MX51_PAD_CSPI1_SS1__GPIO_4_25,
 	MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
 	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+
+	/* reset */
+	MX51_PAD_DI1_PIN13__GPIO_3_2,
+	MX51_PAD_GPIO_1_4__GPIO_1_4,
 };
 
 /* Serial ports */
@@ -297,6 +305,14 @@
 	.num_chipselect = ARRAY_SIZE(mx51_efikamx_spi_cs),
 };
 
+void mx51_efikamx_reset(void)
+{
+	if (system_rev == 0x11)
+		gpio_direction_output(EFIKAMX_RESET1_1, 0);
+	else
+		gpio_direction_output(EFIKAMX_RESET, 0);
+}
+
 static void __init mxc_board_init(void)
 {
 	mxc_iomux_v3_setup_multiple_pads(mx51efikamx_pads,
@@ -318,6 +334,14 @@
 	spi_register_board_info(mx51_efikamx_spi_board_info,
 		ARRAY_SIZE(mx51_efikamx_spi_board_info));
 	imx51_add_ecspi(0, &mx51_efikamx_spi_pdata);
+
+	if (system_rev == 0x11) {
+		gpio_request(EFIKAMX_RESET1_1, "reset");
+		gpio_direction_output(EFIKAMX_RESET1_1, 1);
+	} else {
+		gpio_request(EFIKAMX_RESET, "reset");
+		gpio_direction_output(EFIKAMX_RESET, 1);
+	}
 }
 
 static void __init mx51_efikamx_timer_init(void)
Index: linux-2.6-submit/arch/arm/plat-mxc/include/mach/common.h
===================================================================
--- linux-2.6-submit.orig/arch/arm/plat-mxc/include/mach/common.h	2010-10-27 11:43:11.000000000 +0200
+++ linux-2.6-submit/arch/arm/plat-mxc/include/mach/common.h	2010-10-27 11:43:54.000000000 +0200
@@ -50,5 +50,5 @@
 extern void mxc91231_power_off(void);
 extern void mxc91231_arch_reset(int, const char *);
 extern void mxc91231_prepare_idle(void);
-
+extern void mx51_efikamx_reset(void);
 #endif
Index: linux-2.6-submit/arch/arm/plat-mxc/system.c
===================================================================
--- linux-2.6-submit.orig/arch/arm/plat-mxc/system.c	2010-10-27 11:43:11.000000000 +0200
+++ linux-2.6-submit/arch/arm/plat-mxc/system.c	2010-10-27 14:36:20.000000000 +0200
@@ -26,6 +26,7 @@
 #include <mach/common.h>
 #include <asm/proc-fns.h>
 #include <asm/system.h>
+#include <asm/mach-types.h>
 
 static void __iomem *wdog_base;
 
@@ -42,6 +43,13 @@
 		return;
 	}
 #endif
+#ifdef CONFIG_MACH_MX51_EFIKAMX
+	if (machine_is_mx51_efikamx()) {
+		mx51_efikamx_reset();
+		return;
+	}
+#endif
+
 	if (cpu_is_mx1()) {
 		wcr_enable = (1 << 0);
 	} else {