[PATCH v2 0/3] arm64: dts: rockchip: Add FriendlyElec NanoPi R28S

[安容 via B4 Relay]

The NanoPi R28S is a dual gigabit Ethernet router board based on the
Rockchip RK3528 SoC:

  https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R28S

It is closely related to the already supported NanoPi Zero2, sharing
most of its power tree and peripheral routing. Patch 2 therefore moves
the common parts into rk3528-nanopi.dtsi, and patch 3 adds the board on
top of it. The split leaves the NanoPi Zero2 dtb unchanged; I verified
this by decompiling the dtb before and after the split and comparing
them with the phandle numbering normalised.

The devicetree was derived from the vendor tree:

  https://github.com/friendlyarm/kernel-rockchip/commit/ee640c5344b13a0a317436e2357df01af8268ce7

but with many changes to make it suitable for mainline.

Tested on a metal-case unit without the optional onboard eMMC: boots
from microSD, both Ethernet ports link up at 1000 Mbps, the HYM8563 RTC
registers, and all three LEDs are functional. The USB Type-C connector
registers as a DWC3 UDC in peripheral mode; gadget enumeration against
a USB host was not completed, because that connector is also the 5V
input and a PC port cannot power the board.

Two things I did not do, because my hardware cannot verify them:

- The AICSemi AIC8800D80 WiFi chip on sdio0 has no upstream driver, so
  only the SDIO controller is described.
- The eMMC is described as HS200 rather than the vendor's HS400 with
  enhanced strobe, since the board at hand has an unpopulated eMMC
  footprint and the faster modes could not be verified.

---
Changes in v2:
- Split the parts shared with the NanoPi Zero2 into a new
  rk3528-nanopi.dtsi (new patch 2). The NanoPi Zero2 dtb is unchanged.
- Name the pinctrl labels after the nets in the schematic: usr_btn,
  led1, led2, led_sys, pwr_wf and pcie_eth_perstb.
- Rename the button node to button-user and its label to "USER".
- Link to v1: https://patch.msgid.link/20260905-r28s-upstream-v1-0-f68d5389269a@proton.me

---
安容 (3):
      dt-bindings: arm: rockchip: Add FriendlyElec NanoPi R28S
      arm64: dts: rockchip: Split out the common NanoPi RK3528 parts
      arm64: dts: rockchip: Add devicetree for the FriendlyElec NanoPi R28S

 .../devicetree/bindings/arm/rockchip.yaml          |   5 +
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 .../arm64/boot/dts/rockchip/rk3528-nanopi-r28s.dts | 142 +++++++++++
 .../boot/dts/rockchip/rk3528-nanopi-zero2.dts      | 271 +-------------------
 arch/arm64/boot/dts/rockchip/rk3528-nanopi.dtsi    | 279 +++++++++++++++++++++
 5 files changed, 428 insertions(+), 270 deletions(-)
---
base-commit: 32e0f64640d558a0f5410ac5cdd8ebf371c5e6a6
change-id: 20260905-r28s-upstream-e212e27d6165

Best regards,
--  
安容 <HystericalDragons at proton.me>