[PATCH 2/4] arm64: dts: ti: k3-j7200-common-proc-board: Add ethernet alias

[Siddharth Vadapalli]

On 06/09/26 20:58, Hari Prasath G E wrote:
> Hello Udit,
> 
> On 9/6/2026 7:34 PM, Kumar, Udit wrote:
>>
>>
>> On 9/6/2026 5:48 PM, Hari Prasath G E wrote:
>>> Hello Udit,
>>>
>>> On 9/6/2026 11:13 AM, Kumar, Udit wrote:
>>>>
>>>>
>>>> On 8/11/2026 11:43 AM, Siddharth Vadapalli wrote:
>>>>> Add the 'ethernet0' alias for the Ethernet interface corresponding to
>>>>> the
>>>>> MCU CPSW2G instance of the CPSW Ethernet Switch on the J7200 Common
>>>>> Processor Board.
>>>>>
>>>>> Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
>>>>> ---
>>>>>    arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 1 +
>>>>>    1 file changed, 1 insertion(+)
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/
>>>>> arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>>>> index 54dea36b153b..ac1c1ffe40b7 100644
>>>>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>>>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>>>>> @@ -24,6 +24,7 @@ aliases {
>>>>>            serial5 = &main_uart3;
>>>>>            mmc0 = &main_sdhci0;
>>>>>            mmc1 = &main_sdhci1;
>>>>> +        ethernet0 = &cpsw_port1;
>>>>
>>>> Hello Siddharth,
>>>> As default only 1 cpsw port is enabled for all boards in this series.
>>>> So ethernet0 will be cpsw_port1 always, In case you want to enable more
>>>> port in default config then having aliasing will help.
>>>>
>>>> otherwise, you can consider to add aliasing in overlays where you enable
>>>> more than 1 port.
>>>>
>>>
>>> The first patch in the series for k3-am62a7-sk has two ports enabled by
>>> default, so there it's fine to add alias. Also, there are many other TI
>>
>> May be I am missing something, but i don't see two port are enabled for
>> am62a7
>> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/ 
>> arch/arm64/boot/dts/ti/k3-am62a7-sk.dts#n796
>>
>>
> 
> Apologies, I mistakenly looked at the TI vendor kernel where it's enabled 
> on both ports. I think still the below reasoning is valid to take this 
> patch series in. Let's wait for Siddharth to come back with this comments.

Despite the board having a single Ethernet port enabled, there are two 
reasons for this patch/series:
1. For consistency - keeping these boards on-par with the rest of the K3 
boards (some of which also have a single Ethernet port)
2. As Francesco pointed out at:
https://lore.kernel.org/r/20260906153114.GA3576@francesco-nb/
if PCIe-Ethernet Adapters OR even USB-Ethernet Adapters are used (both of 
which are possible on J7200-Common-Processor-Board which has PCIe and USB 
connectors), we need to specify which of them is 'ethernet0'. For NFS 
(Network File System), if 'ethernet0' isn't specified in the device-tree, 
it is possible that the wrong network interface is used by Linux (despite 
eth0 passed in the Kernel Command Line for NFS) with PCIe/USB Ethernet 
Adapters connected to the board.

Regards,
Siddharth.