[PATCH v7 2/3] pwm: rp1: Add RP1 PWM controller driver

[Christophe JAILLET]

Le 20/07/2026 à 11:44, Andrea della Porta a écrit :
> From: Naushir Patuck <naush at raspberrypi.com>
> 
> The Raspberry Pi RP1 southbridge features an embedded PWM
> controller with 4 output channels, alongside an RPM interface
> to read the fan speed on the Raspberry Pi 5.
> 
> Add the supporting driver.
> 
> Signed-off-by: Naushir Patuck <naush at raspberrypi.com>
> Co-developed-by: Stanimir Varbanov <svarbanov at suse.de>
> Signed-off-by: Stanimir Varbanov <svarbanov at suse.de>
> Signed-off-by: Andrea della Porta <andrea.porta at suse.com>

Hi,

...

> +static int rp1_pwm_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = dev->of_node;
> +	unsigned long clk_rate;
> +	struct pwm_chip *chip;
> +	void __iomem	*base;
> +	struct rp1_pwm *rp1;
> +	int ret;
> +
> +	chip = devm_pwmchip_alloc(dev, RP1_PWM_NUM_PWMS, sizeof(*rp1));
> +	if (IS_ERR(chip))
> +		return PTR_ERR(chip);
> +
> +	rp1 = pwmchip_get_drvdata(chip);
> +
> +	base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	rp1->regmap = devm_regmap_init_mmio(dev, base, &rp1_pwm_regmap_config);
> +	if (IS_ERR(rp1->regmap))
> +		return dev_err_probe(dev, PTR_ERR(rp1->regmap), "Cannot initialize regmap\n");
> +
> +	rp1->clk = devm_clk_get(dev, NULL);

Could it be devm_clk_get_enabled() to simplify the error handling path 
as done above with other devm function?
...

> +	if (IS_ERR(rp1->clk))
> +		return dev_err_probe(dev, PTR_ERR(rp1->clk), "Clock not found\n");
> +
> +	ret = clk_prepare_enable(rp1->clk);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to enable clock\n");

... this also saves these 3 lines.

> +	rp1->clk_enabled = true;
> +
> +	ret = devm_clk_rate_exclusive_get(dev, rp1->clk);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "Failed to get exclusive rate\n");
> +		goto err_disable_clk;
> +	}
> +
> +	clk_rate = clk_get_rate(rp1->clk);
> +	if (!clk_rate) {
> +		ret = dev_err_probe(dev, -EINVAL, "Failed to get clock rate\n");
> +		goto err_disable_clk;
> +	}
> +	/*
> +	 * To prevent u64 overflow in period calculations:
> +	 * mul_u64_u64_div_u64(period_ns, clk_rate, NSEC_PER_SEC)
> +	 * If clk_rate > 1 GHz, the result can overflow.
> +	 */
> +	if (clk_rate > HZ_PER_GHZ) {
> +		ret = dev_err_probe(dev, -EINVAL, "Clock rate > 1 GHz is not supported\n");
> +		goto err_disable_clk;
> +	}
> +	rp1->clk_rate = clk_rate;
> +
> +	chip->ops = &rp1_pwm_ops;
> +	chip->atomic = true;
> +
> +	platform_set_drvdata(pdev, chip);
> +
> +	ret = pwmchip_add(chip);

Could it be devm_pwmchip_add() to simplify the error handling path as 
done above with other devm function?

> +	if (ret) {
> +		dev_err_probe(dev, ret, "Failed to register PWM chip\n");
> +		goto err_disable_clk;
> +	}
> +
> +	ret = of_syscon_register_regmap(np, rp1->regmap);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "Failed to register syscon\n");
> +		goto err_remove_chip;
> +	}
> +
> +	return 0;
> +
> +err_remove_chip:
> +	pwmchip_remove(chip);
> +err_disable_clk:
> +	clk_disable_unprepare(rp1->clk);
> +
> +	return ret;
> +}
...

CJ