[PATCH 2/2] ARM: dts: aspeed: Add NVIDIA MGX Vera C2 BMC

[Krzysztof Kozlowski]

On Thu, Oct 29, 2026 at 01:58:08PM +0900, Jacky Huang wrote:
> +	chosen {
> +		bootargs = "console=tty0 console=ttyS4,115200n8 earlycon";

Drop bootargs. Console (and baudrate) goes to stdout-path. earlycon is
for debugging, not mainline wide-usage.

> +		stdout-path = &uart5;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		fault-led {
> +			gpios = <&exp7 12 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		power-led {
> +			gpios = <&exp7 8 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		uid-led {
> +			gpios = <&exp7 10 GPIO_ACTIVE_LOW>;
> +		};
> +	};

...

> +				device at 1 {
> +					compatible = "usb955,cf11";
> +					reg = <1>;
> +					#address-cells = <2>;
> +					#size-cells = <0>;
> +
> +					cp2112: interface at 1 {
> +						compatible = "usbif955,cf11.config1.1";
> +						reg = <1 1>;
> +						#gpio-cells = <2>;
> +						gpio-controller;
> +						#interrupt-cells = <2>;
> +						interrupt-controller;
> +
> +						i2c {
> +							#address-cells = <1>;
> +							#size-cells = <0>;
> +
> +							/* CPU0 IROT/thermal/SOCAMM/JTAG */
> +							pca9555 at 50 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
If you cannot find a name matching your device, please check in kernel
sources for similar cases or you can grow the spec (via pull request to
DT spec repo).

> +								compatible = "nxp,pca9555";
> +								reg = <0x50>;

...

> +
> +/* Board 0 management bus 1: GPIO expanders + HPM MCU MCTP */
> +&i2c1 {
> +	mctp-controller;
> +	multi-master;
> +
> +	status = "okay";
> +
> +	/* MCTP for HPM MCU */
> +	mctp at 18 {
> +		compatible = "mctp-i2c-controller";
> +		reg = <(0x18 | I2C_OWN_SLAVE_ADDRESS)>;
> +	};
> +
> +	/* Board 0 management bus 1 GPIO expander 0 */
> +	pca9555 at 20 {
> +		compatible = "nxp,pca9555";
> +		reg = <0x20>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
> +		vcc-supply = <&standby_power_regulator>;
> +		gpio-line-names =
> +		"B0_M1_MCU_RESET_L-O",

Messed indentation.

Are you sure you run dt-check-style here?

Best regards,
Krzysztof