[PATCH v2 2/3] ARM: dts: aspeed: add Intel AVCRP BMC

[Tan Siewert]

On 10/12/26 7:39 PM, Dawid Glazik wrote:
> Add the initial AST2600 device tree for the Intel AVCRP BMC platform.
> 
> Signed-off-by: Dawid Glazik <dawid.glazik at linux.intel.com>

You got Review trailers from Andrew Lunn in v1. Unless you think Andrew 
has to re-review it (which should be then reasoned), please keep them in 
new revisions.

 From the kernel docs [0]:

"Both Tested-by and Reviewed-by tags, once received on mailing list from 
tester or reviewer, should be added by author to the applicable patches 
when sending next versions. However if the patch has changed 
substantially in following version, these tags might not be applicable 
anymore and thus should be removed. Usually removal of someone’s 
Acked-by, Tested-by or Reviewed-by tags should be mentioned in the patch 
changelog with an explanation (after the ‘---’ separator)."

> ---
> v2:
>   - Replace bootargs console=ttyS4,115200n8 with stdout-path = &uart5
>   - Remove the unreferenced video_memory reserved-memory node
> ---
>   arch/arm/boot/dts/aspeed/Makefile             |   1 +
>   .../dts/aspeed/aspeed-bmc-intel-avcrp.dts     | 315 ++++++++++++++++++
>   2 files changed, 316 insertions(+)
>   create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-intel-avcrp.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
> index 767f7c7652d5..ea4645ef9872 100644
> --- a/arch/arm/boot/dts/aspeed/Makefile
> +++ b/arch/arm/boot/dts/aspeed/Makefile
> @@ -54,6 +54,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>   	aspeed-bmc-ibm-rainier-4u.dtb \
>   	aspeed-bmc-ibm-sbp1.dtb \
>   	aspeed-bmc-ibm-system1.dtb \
> +	aspeed-bmc-intel-avcrp.dtb \
>   	aspeed-bmc-intel-s2600wf.dtb \
>   	aspeed-bmc-inspur-fp5280g2.dtb \
>   	aspeed-bmc-inspur-nf5280m6.dtb \
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-avcrp.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-avcrp.dts
> new file mode 100644
> index 000000000000..7c088c89d417
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-avcrp.dts
> @@ -0,0 +1,315 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2026 Intel Corporation
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> +	model = "Intel AVCRP BMC";
> +	compatible = "intel,avcrp-bmc", "aspeed,ast2600";
> +
> +	aliases {
> +		serial4 = &uart5;
> +	};
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "earlycon";
> +	};
> +
> +	memory at 80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		video_engine_memory: jpegbuffer {
> +			size = <0x02000000>; /* 32M */
> +			alignment = <0x01000000>;
> +			compatible = "shared-dma-pool";
> +			reusable;
> +		};
> +	};
> +
> +};
> +
> +&rtc {
> +	status = "okay";
> +};

Please sort your nodes, as described in the device tree design guideline 
[1]. There's also a tool called `scripts/dtc/dt-check-style` that can 
help with this.
Note on that: we usually run `--mode strict` but it is known to report 
false-positives, so please check any reported errors twice ^^

> +
> +&fmc {
> +	status = "okay";
> +	flash at 0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "bmc";
> +		spi-rx-bus-width = <4>;
> +		spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-64.dtsi"
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	status = "okay";
> +};
> +
> +&uart5 {
> +	status = "okay";
> +};
> +
> +&uart_routing {
> +	status = "okay";
> +};
> +
> +&mdio1 {
> +	status = "okay";
> +
> +	ethphy1: ethernet-phy at 0 {
> +		compatible = "ethernet-phy-id001c.c916";
> +		reg = <0>;
> +		reset-gpios = <&gpio0 ASPEED_GPIO(C, 1) GPIO_ACTIVE_LOW>;
> +		reset-assert-us = <10000>;
> +		reset-deassert-us = <50000>;
> +	};
> +};
> +
> +&mac1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii2_default>;
> +	clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>,
> +		 <&syscon ASPEED_CLK_MAC2RCLK>;
> +	clock-names = "MACCLK", "RCLK";
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy1>;
> +};
> +
> +&lpc {
> +	lpc_snoop: lpc-snoop at 80 {
> +		snoop-ports = <0x80>;
> +		status = "okay";
> +	};

Why's this named if you don't use it as reference anywhere.

> +};
> +
> +&i3c_global {
> +	status = "okay";
> +};

That's enabled by default.

> +
> +&vhub {
> +	status = "okay";
> +};
> +
> +&video {
> +	status = "okay";
> +	memory-region = <&video_engine_memory>;
> +};
> +
> +&gpio0 {
> +	gpio-line-names =
> +		/*A0-A7*/ "", "", "", "", "SMB_CPU_PIROM_SCL", "SMB_CPU_PIROM_SDA",
> +				"SMB_IPMB_STBY_LVC3_SCL", "SMB_IPMB_STBY_LVC3_SDA",
> +		/*B0-B7*/ "", "", "", "FM_CPU1_ERR2_LVT3_N",
> +				"RGMII_BMC_RMM4_LVC3_R_MDC", "RGMII_BMC_RMM4_LVC3_R_MDIO",

Why do you name reserved GPIO lines (in this case the RGMII lines)? 
They're used by the kernel anyways.

Tan

[0] 
https://docs.kernel.org/process/submitting-patches.html#using-reported-by-tested-by-reviewed-by-suggested-by-and-fixes
[1] https://docs.kernel.org/devicetree/bindings/dts-coding-style.html