[BUG] arm64: PTRACE_SINGLESTEP ignored after perf HW_BREAKPOINT_X trap
毛凡
tybb1992 at gmail.com
Sun Oct 11 20:00:50 PDT 2026
Hi Catalin, Will,
I'd like to confirm whether the following arm64 behaviour is expected.
After a perf hardware instruction breakpoint (PERF_TYPE_BREAKPOINT /
HW_BREAKPOINT_X) traps and is disabled, a PTRACE_SINGLESTEP issued
immediately afterwards is not honored: the tracee runs to completion,
as if PTRACE_CONT had been used. The same single step works when the
breakpoint was armed directly through ptrace (NT_ARM_HW_BREAK). On
x86_64 both paths single-step correctly.
This came up while investigating rr's (the debugger) async-signal replay:
in JIT memory it runs past the recorded point and hits an unrecorded SIGBUS,
and the recovery path arms a perf instruction breakpoint and then
issues one PTRACE_SINGLESTEP to step over the target instruction.
On arm64 that step is swallowed.
Environment:
Linux ubu-aarch64 7.0.0-34-generic #34~24.04.1 SMP PREEMPT_DYNAMIC
Fri Sep 25 20:07:36 CST 2026 aarch64 aarch64 aarch64 GNU/Linux
perf setup: perf_event_open with PERF_TYPE_BREAKPOINT, bp_type
HW_BREAKPOINT_X, bp_len = sizeof(long), precise_ip = 0
(0 is what this kernel accepted; see transcript)
ptrace setup: PTRACE_SETREGSET NT_ARM_HW_BREAK, one dbg_reg slot with
ctrl = 0x1FE5 (EL0 execution breakpoint)
Minimal reproducer: pure C, attached below. It forks a fresh tracee
per case, arms a breakpoint on the first instruction of step_target(),
waits for the SIGTRAP stop with PC == target, disables the breakpoint,
issues exactly one PTRACE_SINGLESTEP, and checks whether the tracee
stopped just past the target or ran the whole tiny loop to completion.
Result on arm64:
platform=aarch64 target=0xaaaab4150c14 (&step_target) iterations=8
Case A: stop via perf hardware breakpoint (HW_BREAKPOINT_X),
then PTRACE_SINGLESTEP
[info] perf_event_open ok with precise_ip=0
breakpoint hit: SIGTRAP at 0xaaaab4150c14
[info] tracee exited with code 0 during 'single step'
case A (perf) SWALLOWED: tracee ran the whole loop and EXITED --
PTRACE_SINGLESTEP behaved like PTRACE_CONT
Case B: stop via ptrace-native hardware breakpoint,
then PTRACE_SINGLESTEP
breakpoint hit: SIGTRAP at 0xaaaab4150c14
case B (ptrace) clean single step: SIGTRAP just past the breakpoint
VERDICT: reproduced on aarch64: after a perf HW_BREAKPOINT_X stop,
PTRACE_SINGLESTEP is ignored (the tracee runs to completion); the
ptrace-native path single-steps correctly. The failure is specific
to the perf breakpoint path, not to single-stepping itself.
Result on x86_64 (same program, real hardware):
Linux ubu-X99 7.0.0-31-generic #31~24.04.1-Ubuntu SMP PREEMPT_DYNAMIC
Mon Aug 10 09:38:02 UTC 2026 x86_64 x86_64 x86_64 GNU/Linux
platform=x86_64 target=0x5e6af7af1129 (&step_target) iterations=8
Case A: stop via perf hardware breakpoint (HW_BREAKPOINT_X), then
PTRACE_SINGLESTEP
[info] perf_event_open ok with precise_ip=0
breakpoint hit: SIGTRAP at 0x5e6af7af1129
case A (perf) clean single step: SIGTRAP just past the breakpoint
Case B: stop via ptrace-native hardware breakpoint, then PTRACE_SINGLESTEP
breakpoint hit: SIGTRAP at 0x5e6af7af1129
case B (ptrace) clean single step: SIGTRAP just past the breakpoint
VERDICT: both cases clean on x86_64: no anomaly observed.
So: same hardware debug exception, same single step, different outcome
depending on whether the breakpoint was armed via perf or via ptrace,
and only on arm64.
Questions:
1. Is this expected behaviour on arm64, or a kernel bug in the perf
breakpoint path?
2. If it is a kernel quirk, what is the recommended way to fast-forward
over a breakpointed instruction on arm64 so that one step retires
exactly one instruction?
3. Is there anything wrong with the reproducer itself? In particular,
is disabling the perf event with PERF_EVENT_IOC_DISABLE before
PTRACE_SINGLESTEP the correct sequence, or does the perf breakpoint
need to be torn down differently on arm64?
One possibly related observation: while writing this, I found that if
PTRACE_SETREGSET(NT_ARM_HW_BREAK) is called with an iov_len covering all
16 slots of struct user_hwdebug_state, the kernel returns ENOSPC even
though only slot 0 carries a valid ctrl. Shrinking iov_len to
dbg_info + one slot makes it succeed. I mention it in case it is a
symptom of the same per-CPU slot bookkeeping.
Reproducer (build with: gcc -O0 -g -fno-plt -o repro repro.c):
/*
* perf_vs_ptrace_step_min.c -- one kernel question, two stop paths.
*
* After a tracee is stopped on a HARDWARE INSTRUCTION BREAKPOINT, does the
* kernel honor a PTRACE_SINGLESTEP issued immediately afterwards?
*
* Case A (perf path, used by rr):
* perf event PERF_TYPE_BREAKPOINT / HW_BREAKPOINT_X, hit delivered as an
* async SIGTRAP. Then PERF_EVENT_IOC_DISABLE and PTRACE_SINGLESTEP.
*
* Case B (plain ptrace path):
* same cpu debug registers programmed directly with ptrace --
* aarch64 PTRACE_SETREGSET NT_ARM_HW_BREAK, x86_64 DR0/DR7 via
* PTRACE_POKEUSER; synchronous SIGTRAP, no perf involvement. Then clear
* the breakpoint and PTRACE_SINGLESTEP.
*
* Observed: aarch64 7.0.0-3x -> Case A swallowed, Case B clean;
* x86_64 7.0.0-31 -> both clean.
*
* Build:
* gcc -O0 -g -fno-plt -o perf_vs_ptrace_step_min perf_vs_ptrace_step_min.c
* ./perf_vs_ptrace_step_min [iterations] (default 8)
*
* Exit code: 0 both clean, 1 Case A broken, 2 Case B broken,
* 3 environment/setup error.
*/
#define _GNU_SOURCE
#include <errno.h>
#include <fcntl.h>
#include <linux/elf.h>
#include <linux/hw_breakpoint.h>
#include <linux/perf_event.h>
#include <sched.h>
#include <signal.h>
#include <stdbool.h>
#include <stddef.h>
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/ioctl.h>
#include <sys/ptrace.h>
#include <sys/syscall.h>
#include <sys/uio.h>
#include <sys/wait.h>
#include <unistd.h>
/* -------------------------------------------------------------------- */
/* Per-arch bits. */
/* -------------------------------------------------------------------- */
#if defined(__aarch64__)
typedef struct {
uint64_t regs[31];
uint64_t sp;
uint64_t pc;
uint64_t pstate;
} user_regs_t;
#define PLATFORM_NAME "aarch64"
#define REG_PC(regs) ((regs).pc)
/* rr uses precise_ip=3 on arm64; we try 0..3 and log which the kernel takes. */
#define PRECISE_IP_DEFAULT 0
#define STEP_PAST_TARGET(regs, target) ((REG_PC(regs)) ==
(uint64_t)(target) + 4)
#elif defined(__x86_64__)
#include <sys/user.h>
typedef struct user_regs_struct user_regs_t;
#define PLATFORM_NAME "x86_64"
#define REG_PC(regs) ((regs).rip)
#define PRECISE_IP_DEFAULT 0
#define STEP_PAST_TARGET(regs, target) ((REG_PC(regs)) > (uint64_t)(target))
#else
#error "this reproducer supports aarch64 and x86_64 only"
#endif
/* -------------------------------------------------------------------- */
/* Traced workload. */
/* -------------------------------------------------------------------- */
static volatile unsigned long g_step_sink;
__attribute__((noinline))
static void step_target(void) {
g_step_sink++;
}
static void run_loop(long iterations) {
while (iterations-- > 0) {
step_target();
}
}
/* -------------------------------------------------------------------- */
/* Shared tracee plumbing. */
/* -------------------------------------------------------------------- */
typedef enum {
CASE_PERF = 0,
CASE_PTRACE = 1,
} test_case_t;
typedef enum {
STEP_CLEAN = 0, /* SIGTRAP stop just past the breakpoint */
STEP_SWALLOWED, /* step degraded to CONT: tracee ran on / exited */
STEP_BROKEN, /* stopped, but not the expected clean SIGTRAP */
SETUP_ERROR, /* could not set up / drive the tracee */
} test_result_t;
static pid_t fork_tracee(long iterations) {
pid_t child = fork();
if (child == 0) {
if (ptrace(PTRACE_TRACEME, 0, 0, 0) < 0) {
_exit(2);
}
raise(SIGSTOP);
run_loop(iterations);
_exit(0);
}
return child;
}
static int read_registers(pid_t pid, user_regs_t *regs) {
struct iovec iov = {.iov_base = regs, .iov_len = sizeof(*regs)};
if (ptrace(PTRACE_GETREGSET, pid, (void *)NT_PRSTATUS, &iov) < 0) {
fprintf(stderr, " [setup] PTRACE_GETREGSET(NT_PRSTATUS): %s\n",
strerror(errno));
return -1;
}
return 0;
}
static int wait_for_initial_stop(pid_t pid) {
int status;
if (waitpid(pid, &status, 0) < 0) {
fprintf(stderr, " [setup] waitpid initial: %s\n", strerror(errno));
return -1;
}
if (!(WIFSTOPPED(status) && WSTOPSIG(status) == SIGSTOP)) {
fprintf(stderr, " [setup] unexpected initial stop, status 0x%x\n", status);
return -1;
}
return 0;
}
static bool wait_breakpoint_stop(pid_t pid, uint64_t target) {
int status;
user_regs_t regs;
if (ptrace(PTRACE_CONT, pid, 0, 0) < 0) {
fprintf(stderr, " [setup] PTRACE_CONT: %s\n", strerror(errno));
return false;
}
if (waitpid(pid, &status, 0) < 0) {
fprintf(stderr, " [setup] waitpid bp: %s\n", strerror(errno));
return false;
}
if (!WIFSTOPPED(status) || WSTOPSIG(status) != SIGTRAP) {
fprintf(stderr, " [setup] breakpoint stop failed, status 0x%x%s\n",
status, WIFEXITED(status) ? " (tracee EXITED)" : "");
return false;
}
if (read_registers(pid, ®s) < 0) {
return false;
}
if (REG_PC(regs) != target) {
fprintf(stderr, " [setup] stopped at %#llx (want %#llx)\n",
(unsigned long long)REG_PC(regs), (unsigned long long)target);
return false;
}
return true;
}
static test_result_t single_step_and_classify(pid_t pid, uint64_t target) {
int status;
user_regs_t regs;
if (ptrace(PTRACE_SINGLESTEP, pid, 0, 0) < 0) {
fprintf(stderr, " [setup] PTRACE_SINGLESTEP: %s\n", strerror(errno));
return SETUP_ERROR;
}
if (waitpid(pid, &status, 0) < 0) {
fprintf(stderr, " [setup] waitpid step: %s\n", strerror(errno));
return SETUP_ERROR;
}
if (WIFEXITED(status)) {
fprintf(stderr, " [info] tracee exited with code %d during
'single step'\n",
WEXITSTATUS(status));
return STEP_SWALLOWED;
}
if (WIFSIGNALED(status)) {
fprintf(stderr, " [info] tracee killed by signal %d during
'single step'\n",
WTERMSIG(status));
return STEP_BROKEN;
}
if (!WIFSTOPPED(status)) {
return STEP_BROKEN;
}
if (read_registers(pid, ®s) < 0) {
return SETUP_ERROR;
}
if (WSTOPSIG(status) == SIGTRAP && STEP_PAST_TARGET(regs, target)) {
return STEP_CLEAN;
}
fprintf(stderr, " [info] step stopped with sig %d pc=%#llx (want
pc=%#llx)\n",
WSTOPSIG(status), (unsigned long long)REG_PC(regs),
(unsigned long long)target);
return STEP_BROKEN;
}
/* -------------------------------------------------------------------- */
/* Case A: perf hardware instruction breakpoint. */
/* -------------------------------------------------------------------- */
/* Try precise_ip 0..3 and log every failure, so the transcript shows what
* the kernel actually accepts on this machine. */
static int create_perf_breakpoint(pid_t pid, uint64_t target, int
*used_precise) {
static const int precise_candidates[] = {PRECISE_IP_DEFAULT, 1, 2, 3};
struct perf_event_attr attr;
int fd;
for (size_t i = 0;
i < sizeof(precise_candidates) / sizeof(precise_candidates[0]); i++) {
int precise = precise_candidates[i];
memset(&attr, 0, sizeof(attr));
attr.type = PERF_TYPE_BREAKPOINT;
attr.size = sizeof(attr);
attr.bp_type = HW_BREAKPOINT_X;
attr.bp_len = sizeof(long);
attr.sample_period = 1;
attr.sample_type = PERF_SAMPLE_IP;
attr.pinned = 1;
attr.exclude_kernel = 1;
attr.exclude_hv = 1;
attr.wakeup_events = 1;
attr.precise_ip = precise;
attr.bp_addr = target;
attr.disabled = 0;
fd = syscall(__NR_perf_event_open, &attr, pid, -1, -1,
PERF_FLAG_FD_CLOEXEC);
if (fd >= 0) {
*used_precise = precise;
return fd;
}
fprintf(stderr, " [setup] perf_event_open(precise_ip=%d): %s\n",
precise, strerror(errno));
}
return -1;
}
static int arm_perf_breakpoint(pid_t pid, uint64_t target, int *perf_fd) {
int used_precise = -1;
int fd = create_perf_breakpoint(pid, target, &used_precise);
if (fd < 0) {
return -1;
}
struct f_owner_ex owner = {.type = F_OWNER_TID, .pid = pid};
if (fcntl(fd, F_SETOWN_EX, &owner) < 0) {
fprintf(stderr, " [setup] fcntl(F_SETOWN_EX): %s\n", strerror(errno));
close(fd);
return -1;
}
if (fcntl(fd, F_SETFL, O_ASYNC) < 0) {
fprintf(stderr, " [setup] fcntl(F_SETFL, O_ASYNC): %s\n", strerror(errno));
close(fd);
return -1;
}
if (fcntl(fd, F_SETSIG, SIGTRAP) < 0) {
fprintf(stderr, " [setup] fcntl(F_SETSIG, SIGTRAP): %s\n",
strerror(errno));
close(fd);
return -1;
}
if (ioctl(fd, PERF_EVENT_IOC_ENABLE, 0) < 0) {
fprintf(stderr, " [setup] PERF_EVENT_IOC_ENABLE: %s\n", strerror(errno));
close(fd);
return -1;
}
printf(" [info] perf_event_open ok with precise_ip=%d\n", used_precise);
*perf_fd = fd;
return 0;
}
/* -------------------------------------------------------------------- */
/* Case B: ptrace-native hardware breakpoint. */
/* -------------------------------------------------------------------- */
#if defined(__aarch64__)
typedef struct {
uint64_t addr;
uint32_t ctrl;
uint32_t pad;
} hw_bp_reg_t;
typedef struct {
uint32_t dbg_info;
uint32_t pad;
hw_bp_reg_t dbg_regs[16];
} hw_debug_state_t;
#define AARCH64_EXEC_BP_CTRL 0x1FE5u
#define AARCH64_DEBUG_REG_MAX 16
/* Arm an EL0 execution breakpoint via PTRACE_SETREGSET(NT_ARM_HW_BREAK).
* iov_len covers dbg_info + exactly one slot: asking for all 16 slots makes
* the kernel try to reserve every slot and fail with ENOSPC on cores with
* fewer hardware breakpoints. Per-CPU slot bookkeeping means a usable CPU
* must be picked, so retry across CPUs. */
static int set_native_breakpoint(pid_t pid, uint64_t target) {
hw_debug_state_t state;
memset(&state, 0, sizeof(state));
state.dbg_regs[0].addr = target;
state.dbg_regs[0].ctrl = AARCH64_EXEC_BP_CTRL;
struct iovec iov = {
.iov_base = &state,
.iov_len = offsetof(hw_debug_state_t, dbg_regs) +
sizeof(state.dbg_regs[0]),
};
for (int cpu = 0; cpu < AARCH64_DEBUG_REG_MAX; cpu++) {
cpu_set_t set;
CPU_ZERO(&set);
CPU_SET(cpu, &set);
if (sched_setaffinity(0, sizeof(set), &set) < 0) {
continue;
}
if (ptrace(PTRACE_SETREGSET, pid, (void *)NT_ARM_HW_BREAK, &iov) == 0) {
return 0;
}
fprintf(stderr, " [setup] NT_ARM_HW_BREAK on cpu %d: %s\n",
cpu, strerror(errno));
}
return -1;
}
static void clear_native_breakpoint(pid_t pid) {
hw_debug_state_t zero;
memset(&zero, 0, sizeof(zero));
struct iovec iov = {
.iov_base = &zero,
.iov_len = offsetof(hw_debug_state_t, dbg_regs) +
sizeof(zero.dbg_regs[0]),
};
if (ptrace(PTRACE_SETREGSET, pid, (void *)NT_ARM_HW_BREAK, &iov) < 0) {
fprintf(stderr, " [setup] clear NT_ARM_HW_BREAK: %s\n", strerror(errno));
}
}
#elif defined(__x86_64__)
static int set_native_breakpoint(pid_t pid, uint64_t target) {
if (ptrace(PTRACE_POKEUSER, pid,
offsetof(struct user, u_debugreg[0]), target) < 0) {
fprintf(stderr, " [setup] POKEUSER DR0: %s\n", strerror(errno));
return -1;
}
if (ptrace(PTRACE_POKEUSER, pid,
offsetof(struct user, u_debugreg[7]), 0x1) < 0) {
fprintf(stderr, " [setup] POKEUSER DR7: %s\n", strerror(errno));
return -1;
}
return 0;
}
static void clear_native_breakpoint(pid_t pid) {
ptrace(PTRACE_POKEUSER, pid, offsetof(struct user, u_debugreg[7]), 0);
ptrace(PTRACE_POKEUSER, pid, offsetof(struct user, u_debugreg[0]), 0);
}
#endif
/* -------------------------------------------------------------------- */
/* Per-case driver: arm -> hit -> disable/clear -> one step -> classify */
/* -------------------------------------------------------------------- */
static test_result_t run_one_case(test_case_t which, long iterations,
uint64_t target) {
pid_t child = fork_tracee(iterations);
if (child < 0) {
fprintf(stderr, " [setup] fork: %s\n", strerror(errno));
return SETUP_ERROR;
}
int perf_fd = -1;
if (wait_for_initial_stop(child) < 0) {
kill(child, SIGKILL);
waitpid(child, NULL, 0);
return SETUP_ERROR;
}
if (which == CASE_PERF) {
if (arm_perf_breakpoint(child, target, &perf_fd) < 0) {
kill(child, SIGKILL);
waitpid(child, NULL, 0);
return SETUP_ERROR;
}
} else {
if (set_native_breakpoint(child, target) < 0) {
kill(child, SIGKILL);
waitpid(child, NULL, 0);
return SETUP_ERROR;
}
}
if (!wait_breakpoint_stop(child, target)) {
kill(child, SIGKILL);
waitpid(child, NULL, 0);
return SETUP_ERROR;
}
printf(" breakpoint hit: SIGTRAP at %#llx\n", (unsigned long long)target);
if (which == CASE_PERF) {
if (ioctl(perf_fd, PERF_EVENT_IOC_DISABLE, 0) < 0) {
fprintf(stderr, " [setup] PERF_EVENT_IOC_DISABLE: %s\n",
strerror(errno));
}
close(perf_fd);
} else {
clear_native_breakpoint(child);
}
test_result_t result = single_step_and_classify(child, target);
kill(child, SIGKILL);
waitpid(child, NULL, 0);
return result;
}
/* -------------------------------------------------------------------- */
/* Output helpers and main. */
/* -------------------------------------------------------------------- */
static void print_result(const char *label, test_result_t result) {
const char *text;
switch (result) {
case STEP_CLEAN:
text = "clean single step: SIGTRAP just past the breakpoint";
break;
case STEP_SWALLOWED:
text = "SWALLOWED: tracee ran the whole loop and EXITED -- "
"PTRACE_SINGLESTEP behaved like PTRACE_CONT";
break;
case STEP_BROKEN:
text = "BROKEN: unexpected stop after the single step";
break;
default:
text = "SETUP ERROR: see the errors above";
break;
}
printf(" %-14s %s\n", label, text);
}
/* Verdict is written to be pasted into a bug report verbatim: it states
* what was observed, without over-claiming on incomplete data. */
static void print_verdict(test_result_t a, test_result_t b,
const char *platform) {
printf("\nVERDICT: ");
if (a == SETUP_ERROR || b == SETUP_ERROR) {
printf("inconclusive on this run -- at least one case could not be "
"set up (see the [setup] lines above); no conclusion drawn.\n");
} else if (a == STEP_SWALLOWED && b == STEP_CLEAN) {
printf("reproduced on %s: after a perf HW_BREAKPOINT_X stop, "
"PTRACE_SINGLESTEP is ignored (the tracee runs to completion); "
"the ptrace-native path single-steps correctly. The failure is "
"specific to the perf breakpoint path, not to single-stepping "
"itself.\n", platform);
} else if (b == STEP_SWALLOWED || b == STEP_BROKEN) {
printf("unexpected on %s: the ptrace-native path also fails to "
"single-step; the perf-vs-ptrace distinction does not hold.\n",
platform);
} else if (a == STEP_CLEAN && b == STEP_CLEAN) {
printf("both cases clean on %s: no anomaly observed.\n", platform);
} else {
printf("no clean comparison on %s (case A=%d, case B=%d); rerun and "
"inspect the [setup]/[info] lines above.\n", platform, a, b);
}
}
int main(int argc, char **argv) {
long iterations = argc > 1 ? atol(argv[1]) : 8;
uint64_t target = (uint64_t)(uintptr_t)&step_target;
printf("platform=%s target=%#llx (&step_target) iterations=%ld\n\n",
PLATFORM_NAME, (unsigned long long)target, iterations);
printf("Case A: stop via perf hardware breakpoint (HW_BREAKPOINT_X), "
"then PTRACE_SINGLESTEP\n");
test_result_t result_a = run_one_case(CASE_PERF, iterations, target);
print_result("case A (perf)", result_a);
printf("\nCase B: stop via ptrace-native hardware breakpoint, "
"then PTRACE_SINGLESTEP\n");
test_result_t result_b = run_one_case(CASE_PTRACE, iterations, target);
print_result("case B (ptrace)", result_b);
print_verdict(result_a, result_b, PLATFORM_NAME);
if (result_a == STEP_SWALLOWED || result_a == STEP_BROKEN) return 1;
if (result_b == STEP_SWALLOWED || result_b == STEP_BROKEN) return 2;
if (result_a == SETUP_ERROR || result_b == SETUP_ERROR) return 3;
return 0;
}
Thanks a lot for any advice.
More information about the linux-arm-kernel
mailing list