[PATCH v2 15/17] ARM: dts: samsung: exynos4210-smdkv310: sort properties

[Henrik Grimler]

And add or delete newlines where applicable, and sort properties
according to the preferred style. Fixes warnings from dt-check-style
like:

  samsung/exynos4210-smdkv310.dts:90: [property-order] property 'wakeup-source' out of canonical order (should sort before 'linux,input-no-autorepeat')
  samsung/exynos4210-smdkv310.dts:91: [property-order] property 'pinctrl-names' must be placed after 'pinctrl-0'
  samsung/exynos4210-smdkv310.dts:93: [required-blank-lines] "status" must be preceded by a blank line

Signed-off-by: Henrik Grimler <henrik.grimler at axis.com>
---
 arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)

diff --git a/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts b/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts
index a6b73a8967c6..609853bb840a 100644
--- a/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-smdkv310.dts
@@ -60,6 +60,7 @@ map0 {
 			/* Corresponds to 800MHz */
 			cooling-device = <&cpu0 2 2>;
 		};
+
 		map1 {
 			/* Corresponds to 200MHz */
 			cooling-device = <&cpu0 4 4>;
@@ -70,6 +71,7 @@ map1 {
 &i2c_0 {
 	samsung,i2c-sda-delay = <100>;
 	samsung,i2c-max-bus-freq = <100000>;
+
 	status = "okay";
 
 	eeprom at 50 {
@@ -84,12 +86,13 @@ eeprom at 52 {
 };
 
 &keypad {
+	wakeup-source;
+	pinctrl-0 = <&keypad_rows &keypad_cols>;
+	pinctrl-names = "default";
 	samsung,keypad-num-rows = <2>;
 	samsung,keypad-num-columns = <8>;
 	linux,input-no-autorepeat;
-	wakeup-source;
-	pinctrl-names = "default";
-	pinctrl-0 = <&keypad_rows &keypad_cols>;
+
 	status = "okay";
 
 	key-1 {
@@ -177,8 +180,9 @@ &rtc {
 
 &sdhci_2 {
 	bus-width = <4>;
-	pinctrl-names = "default";
 	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+	pinctrl-names = "default";
+
 	status = "okay";
 };
 
@@ -200,13 +204,14 @@ &serial_3 {
 
 &spi_2 {
 	cs-gpios = <&gpc1 2 GPIO_ACTIVE_HIGH>;
+
 	status = "okay";
 
 	flash at 0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
 		compatible = "winbond,w25x80", "jedec,spi-nor";
 		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
 		spi-max-frequency = <1000000>;
 
 		controller-data {
@@ -214,14 +219,14 @@ controller-data {
 		};
 
 		partition at 0 {
-			label = "U-Boot";
 			reg = <0x0 0x40000>;
+			label = "U-Boot";
 			read-only;
 		};
 
 		partition at 40000 {
-			label = "Kernel";
 			reg = <0x40000 0xc0000>;
+			label = "Kernel";
 		};
 	};
 };

-- 
2.43.0