[PATCH v2 11/17] ARM: dts: samsung: exynos4210-i9100: sort properties
Henrik Grimler
henrik.grimler at axis.com
Tue Oct 6 04:57:25 PDT 2026
And add or delete newlines where applicable, and sort properties
according to the preferred style. Fixes warnings from dt-check-style
like:
samsung/exynos4210-i9100.dts:275: [child-name-order] child node 'pmic-ap-clk' out of name order
samsung/exynos4210-i9100.dts:287: [required-blank-lines] "status" must be preceded by a blank line
samsung/exynos4210-i9100.dts:288: [property-order] property 'assigned-clocks' out of canonical order (should sort before 'status')
Also remove double spaces in max8997 buck dvs voltages list.
Signed-off-by: Henrik Grimler <henrik.grimler at axis.com>
---
arch/arm/boot/dts/samsung/exynos4210-i9100.dts | 125 +++++++++++++------------
1 file changed, 65 insertions(+), 60 deletions(-)
diff --git a/arch/arm/boot/dts/samsung/exynos4210-i9100.dts b/arch/arm/boot/dts/samsung/exynos4210-i9100.dts
index b9a31714381c..85e4d334a5e6 100644
--- a/arch/arm/boot/dts/samsung/exynos4210-i9100.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-i9100.dts
@@ -97,31 +97,31 @@ gpio-keys {
key-vol-down {
gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEDOWN>;
label = "volume down";
debounce-interval = <10>;
+ linux,code = <KEY_VOLUMEDOWN>;
};
key-vol-up {
gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEUP>;
label = "volume up";
debounce-interval = <10>;
+ linux,code = <KEY_VOLUMEUP>;
};
key-power {
gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
label = "power";
debounce-interval = <10>;
wakeup-source;
+ linux,code = <KEY_POWER>;
};
key-ok {
gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_OK>;
label = "ok";
debounce-interval = <10>;
+ linux,code = <KEY_OK>;
};
};
@@ -141,6 +141,7 @@ i2c_max17042_fuel: i2c-9 {
battery at 36 {
compatible = "maxim,max17042";
+ reg = <0x36>;
interrupt-parent = <&gpx2>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
@@ -148,7 +149,6 @@ battery at 36 {
pinctrl-0 = <&max17042_fuel_irq>;
pinctrl-names = "default";
- reg = <0x36>;
maxim,over-heat-temp = <700>;
maxim,over-volt = <4500>;
};
@@ -284,21 +284,24 @@ pmic_ap_clk: pmic-ap-clk {
&camera {
pinctrl-0 = <&cam_port_a_clk_active>;
pinctrl-names = "default";
- status = "okay";
assigned-clocks = <&clock CLK_MOUT_CAM0>, <&clock CLK_MOUT_CAM1>;
assigned-clock-parents = <&clock CLK_XUSBXTI>, <&clock CLK_XUSBXTI>;
+
+ status = "okay";
};
&csis_1 {
- status = "okay";
vddcore-supply = <&vusb_reg>;
vddio-supply = <&vmipi_reg>;
clock-frequency = <160000000>;
#address-cells = <1>;
#size-cells = <0>;
+ status = "okay";
+
port at 4 {
reg = <4>;
+
csis1_ep: endpoint {
remote-endpoint = <&s5k5bafx_ep>;
data-lanes = <1>;
@@ -317,6 +320,7 @@ map0 {
/* Corresponds to 800MHz */
cooling-device = <&cpu0 2 2>;
};
+
map1 {
/* Corresponds to 200MHz */
cooling-device = <&cpu0 4 4>;
@@ -325,62 +329,63 @@ map1 {
};
&ehci {
- status = "okay";
-
phys = <&exynos_usbphy 1>;
phy-names = "host";
-};
-&exynos_usbphy {
status = "okay";
+};
+&exynos_usbphy {
vbus-supply = <&safe1_sreg>;
-};
-&fimc_0 {
status = "okay";
+};
+&fimc_0 {
assigned-clocks = <&clock CLK_MOUT_FIMC0>, <&clock CLK_SCLK_FIMC0>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimc_1 {
- /* Back camera not implemented */
- status = "disabled";
-
assigned-clocks = <&clock CLK_MOUT_FIMC1>, <&clock CLK_SCLK_FIMC1>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ /* Back camera not implemented */
+ status = "disabled";
};
&fimc_2 {
- status = "okay";
-
assigned-clocks = <&clock CLK_MOUT_FIMC2>, <&clock CLK_SCLK_FIMC2>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimc_3 {
- /* Back camera not implemented */
- status = "disabled";
-
assigned-clocks = <&clock CLK_MOUT_FIMC3>, <&clock CLK_SCLK_FIMC3>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ /* Back camera not implemented */
+ status = "disabled";
};
&fimd {
- status = "okay";
#address-cells = <1>;
#size-cells = <0>;
+ pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
+ pinctrl-names = "default";
+
samsung,invert-vden;
samsung,invert-vclk;
- pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
- pinctrl-names = "default";
+ status = "okay";
port at 3 {
reg = <3>;
@@ -392,26 +397,26 @@ fimd_dpi_ep: endpoint {
};
&gpu {
- status = "okay";
-
mali-supply = <&vg3d_breg>;
-};
-&hsotg {
status = "okay";
+};
+&hsotg {
dr_mode = "otg";
vusb_d-supply = <&vusb_reg>;
vusb_a-supply = <&vusbdac_reg>;
-};
-&i2c_1 {
status = "okay";
+};
+&i2c_1 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
+ status = "okay";
+
lis3dh: accelerometer at 19 {
compatible = "st,lis3dh-accel";
reg = <0x19>;
@@ -423,14 +428,14 @@ lis3dh: accelerometer at 19 {
};
&i2c_3 {
- status = "okay";
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
+ status = "okay";
touchscreen at 4a {
compatible = "atmel,maxtouch";
@@ -442,14 +447,14 @@ touchscreen at 4a {
};
&i2c_5 {
- status = "okay";
+ pinctrl-0 = <&i2c5_bus>;
+ pinctrl-names = "default";
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c5_bus>;
- pinctrl-names = "default";
+ status = "okay";
pmic at 66 {
compatible = "maxim,max8997-pmic";
@@ -458,6 +463,11 @@ pmic at 66 {
interrupts-extended = <&gpx0 7 IRQ_TYPE_NONE>,
<&gpx2 3 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&max8997_irq>, <&otg_gp>, <&usb_sel>;
+ pinctrl-names = "default";
+
+ charger-supply = <&charger_reg>;
+
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
max8997,pmic-buck5-uses-gpio-dvs;
@@ -475,34 +485,28 @@ pmic at 66 {
<1000000>, <950000>;
max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
- <950000>, <900000>,
+ <950000>, <900000>,
<1100000>, <1000000>,
- <950000>, <900000>;
+ <950000>, <900000>;
max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>;
- pinctrl-0 = <&max8997_irq>, <&otg_gp>, <&usb_sel>;
- pinctrl-names = "default";
-
- charger-supply = <&charger_reg>;
-
regulators {
vadc_reg: LDO1 {
regulator-name = "VADC_3.3V_C210";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
-
};
+
valive_reg: LDO2 {
regulator-name = "VALIVE_1.1V_C210";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
-
};
vusb_reg: LDO3 {
@@ -706,14 +710,14 @@ CHARGER_TOPOFF {
};
&i2c_7 {
- status = "okay";
+ pinctrl-0 = <&i2c7_bus>;
+ pinctrl-names = "default";
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c7_bus>;
- pinctrl-names = "default";
+ status = "okay";
magnetometer at c {
compatible = "asahi-kasei,ak8975";
@@ -724,8 +728,8 @@ magnetometer at c {
};
&pinctrl_0 {
- pinctrl-names = "default";
pinctrl-0 = <&sleep0>;
+ pinctrl-names = "default";
sleep0: sleep-state {
gpa0-0-pin {
@@ -822,36 +826,35 @@ tsp224_irq: tsp224-irq-pins {
};
&rtc {
- status = "okay";
clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
clock-names = "rtc", "rtc_src";
-};
-&sdhci_0 {
status = "okay";
+};
+&sdhci_0 {
bus-width = <8>;
non-removable;
vmmc-supply = <&vemmc_reg>;
pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_bus8>;
pinctrl-names = "default";
-};
-&sdhci_2 {
status = "okay";
+};
+&sdhci_2 {
bus-width = <4>;
cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vtf_reg>;
pinctrl-0 = <&sd2_clk>, <&sd2_cmd>, <&sd2_bus4>;
pinctrl-names = "default";
-};
-&sdhci_3 {
status = "okay";
+};
+&sdhci_3 {
#address-cells = <1>;
#size-cells = <0>;
@@ -861,8 +864,10 @@ &sdhci_3 {
mmc-pwrseq = <&wlan_pwrseq>;
vmmc-supply = <&vtf_reg>;
- pinctrl-names = "default";
pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+ pinctrl-names = "default";
+
+ status = "okay";
brcmf: wifi at 1 {
compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
@@ -875,13 +880,13 @@ brcmf: wifi at 1 {
};
&serial_0 {
- status = "okay";
-
- pinctrl-names = "default";
pinctrl-0 = <&bt_en>, <&bt_res>, <&uart0_data>, <&uart0_fctl>;
+ pinctrl-names = "default";
uart-has-rtscts;
+ status = "okay";
+
bluetooth {
compatible = "brcm,bcm4330-bt";
--
2.43.0
More information about the linux-arm-kernel
mailing list