[PATCH 1/4] thunderbolt: add platform nhi driver

[Chunfeng Yun (云春峰)]

On 一, 2026-11-09 at 14:56 +0100, Konrad Dybcio wrote:
> 
> External email : Please do not click links or open attachments until
> you have verified the sender or the content.
> 
> 
> On 11/7/26 8:04 PM, Sven Peter wrote:
> > > Add a new file plat.c to register platform NHI driver for
> > > MediaTek
> > > mt8901/mt8992 SoCs.
> > > 
> > > Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> > > 
> > 
> > [...]
> > 
> > > +
> > > +static void nhi_plat_shutdown(struct platform_device *pdev)
> > > +{
> > > +    nhi_plat_do_remove(pdev, true);
> > > +}
> > > +
> > > +
> > > +#ifdef CONFIG_OF
> > > +static const struct of_device_id nhi_plat_of_match[] = {
> > > +    { .compatible = "thunderbolt-platform" },
> > 
> > Do you already have hardware that probes via device tree? You'll
> > have to
> > write bindings and get them reviewed before adding any compatible
> > here.
> > Generic ones like you used here aren't usually allowed.
> > 
> > If you don't have a dts based platform I'd probably drop this, not
> > much of
> > this code here is e.g. re-usable for Apple since they like to think
> > very
> > different, see my series in [1] that I can pick up again now that
> > we
> > made progress on how to represent connections between the NHI and
> > the
> > protocol adapters.
> > 
> > Not sure about qualcom since I haven't seen a series for the NHI
> > yet but
> > I'm sure Konrad can comment there. I kinda expect that it won't
> > have
> > much shared code either.
> 
> We're in the same boat regarding thinking different. This driver is
> for implementations where the underlying hardware is abstracted away
> (be it through architecture or intermediate firmware) and the TBT
> layer writes are enough to e.g. power sequence the connected buses,
> just like on Intel.
You are right, on MediaTek platforms, all vendor-specific operations
and power sequencing are hidden inside the firmware and handled via
ACPI events, so no vendor quirks are needed in the kernel driver
ideally, at least until now. This allows the exact same firmware to
support both Windows and Linux (Ubuntu) using a generic usb4 driver.

Thanks
> 
> For the OF compatible, we definitely do need bindings and I too would
> like to know if this is actually exercised - if not, we should cut it
> out and trivially bring it back when/if the need comes around.
> 
> > Take a look at e.g. more recent drivers in drivers/usb/dwc3: They
> > usually add a dwc3-$vendor.c file that takes care of all the
> > vendor-specific quirks and that ends up being nicer than a single
> > platform.c file with tons of quirks and separate code paths for
> > each and
> > every vendor.
> 
> Yeah, this is a nice parallel. Adding to it, there not only exist
> dwc3-$vendor drivers that take care of the additional registers and
> whatnot, but also everything around the USB subsystem - PHYs, perhaps
> some NoC drivers, and all the infra that feeds into there, and it
> compounds back into the size of some of those dwc3 glue drivers..
> 
> 
> That being said, the makers of the spec probably wanted/expected the
> hardware to have exactly this neat level of abstraction and I
> wouldn't be surprised if more designs end up being compatible. Or if
> the platform firmware makes it appear so.
> 
> Konrad