[PATCH v1 5/7] arm64: dts: ti: k3-am69-aquila: Add Toradex Capacitive Touch Display 10.1" DSI
Vitor Soares
ivitro at gmail.com
Fri May 29 05:08:57 PDT 2026
From: Vitor Soares <vitor.soares at toradex.com>
Add a device tree overlay for the Toradex Capacitive Touch Display 10.1"
DSI on the Aquila DSI_1 interface. Used on the Clover Board (J12), where
DSI_1 is exposed via a FFC/FPC connector.
The display includes an internal Texas Instruments SN65DSI83 DSI-to-LVDS
bridge driving a Riverdi RVT101HVLNWC00 10.1" WXGA IPS TFT LCD panel.
Touch input is provided by an Ilitek ILI2132 capacitive touch controller.
The overlay is also combined with the Aquila AM69 Clover carrier board
device tree to provide a ready-to-use DTB.
Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-dsi
Signed-off-by: Vitor Soares <vitor.soares at toradex.com>
---
arch/arm64/boot/dts/ti/Makefile | 5 +
...m69-aquila-panel-cap-touch-10inch-dsi.dtso | 149 ++++++++++++++++++
2 files changed, 154 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-panel-cap-touch-10inch-dsi.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index ce667843e58b..f9163643291d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -172,15 +172,20 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-rpi-cam-imx219.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm-csi2-quad-tevi-ov5640.dtbo
# Boards with J784s4 SoC
+k3-am69-aquila-clover-panel-cap-touch-10inch-dsi-dtbs := \
+ k3-am69-aquila-clover.dtb \
+ k3-am69-aquila-panel-cap-touch-10inch-dsi.dtbo
k3-am69-aquila-dev-dsi-to-hdmi-dtbs := k3-am69-aquila-dev.dtb \
k3-am69-aquila-dsi-to-hdmi.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-adapter-panel-cap-touch-10inch-dsi.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-adapter-panel-cap-touch-7inch-dsi.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-clover-panel-cap-touch-10inch-dsi.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-clover.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev-dsi-to-hdmi.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dsi-to-hdmi.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dsi-to-lvds-panel-cap-touch-10inch.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-panel-cap-touch-10inch-dsi.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk-pcie0-ep.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am69-aquila-panel-cap-touch-10inch-dsi.dtso b/arch/arm64/boot/dts/ti/k3-am69-aquila-panel-cap-touch-10inch-dsi.dtso
new file mode 100644
index 000000000000..3880026951f3
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am69-aquila-panel-cap-touch-10inch-dsi.dtso
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Toradex Capacitive Touch Display 10.1" on Aquila DSI_1.
+ * Used on Clover Board (J12), DSI_1 is exposed via a FFC/FPC connector.
+ *
+ * https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-dsi
+ * https://www.toradex.com/accessories/capacitive-touch-display-10.1-inch-dsi
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+ backlight_pwm3: backlight-pwm3 {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 45 63 88 119 158 203 255>;
+ default-brightness-level = <4>;
+ /* Aquila PWM_3_DSI (AQUILA B46) */
+ pwms = <&main_ehrpwm5 0 6666667 0>;
+ };
+
+ panel-lvds-bridge {
+ compatible = "riverdi,rvt101hvlnwc00", "panel-lvds";
+ backlight = <&backlight_pwm3>;
+ data-mapping = "vesa-24";
+ height-mm = <136>;
+ width-mm = <217>;
+
+ panel-timing {
+ clock-frequency = <72400000>;
+ de-active = <1>;
+ hactive = <1280>;
+ hback-porch = <83 83 83>;
+ hfront-porch = <12 72 132>;
+ hsync-active = <0>;
+ hsync-len = <1 5 40>;
+ pixelclk-active = <1>;
+ vactive = <800>;
+ vback-porch = <13 13 13>;
+ vfront-porch = <1 15 49>;
+ vsync-active = <0>;
+ vsync-len = <1 10 20>;
+ };
+
+ port {
+ panel_lvds_bridge_in: endpoint {
+ remote-endpoint = <&dsi_lvds_bridge_out>;
+ };
+ };
+ };
+};
+
+&dphy_tx0 {
+ status = "okay";
+};
+
+&dsi0 {
+ status = "okay";
+};
+
+&dsi0_ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ dsi0_out: endpoint {
+ remote-endpoint = <&dsi_lvds_bridge_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpi2_out>;
+ };
+ };
+};
+
+&dss_ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 2 {
+ reg = <2>;
+
+ dpi2_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+};
+
+/* Aquila I2C_3_DSI1 */
+&main_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ bridge at 2c {
+ compatible = "ti,sn65dsi83";
+ reg = <0x2c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_20_dsi_1>;
+ /* Aquila GPIO_20_DSI_1 (AQUILA B45) */
+ enable-gpios = <&main_gpio0 18 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ dsi_lvds_bridge_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ dsi_lvds_bridge_out: endpoint {
+ remote-endpoint = <&panel_lvds_bridge_in>;
+ };
+ };
+ };
+ };
+
+ touchscreen at 41 {
+ compatible = "ilitek,ili2132";
+ reg = <0x41>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_17_dsi_1>, <&pinctrl_gpio_18_dsi_1>;
+ /* Aquila GPIO_17_DSI_1 (AQUILA B42) */
+ interrupt-parent = <&main_gpio0>;
+ interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+ /* Aquila GPIO_18_DSI_1 (AQUILA B43) */
+ reset-gpios = <&main_gpio0 31 GPIO_ACTIVE_LOW>;
+ };
+};
--
2.54.0
More information about the linux-arm-kernel
mailing list