[PATCH v30 5/5] i2c: ast2600: Add target mode support
Ryan Chen
ryan_chen at aspeedtech.com
Thu May 28 00:41:40 PDT 2026
Add target mode support to the AST2600 I2C driver.
Target mode features implemented include:
- Add target interrupt handling
- Address match and response logic
This complements the existing controller-mode support, enabling
dual-role capability.
Signed-off-by: Ryan Chen <ryan_chen at aspeedtech.com>
---
Changes in v30:
- Address Sashiko AI code review feedback:
- Force-stop path (target IRQ aborting an in-flight controller
transfer): disable the controller IER and W1C-clear pending ISR
before calling complete(), then restore the IER after the wake-up.
Without the disable/clear sequence the controller IRQ handler can
race with the target abort path and double-complete or touch
freed msgs.
- unreg_target() teardown ordering: disable the target IER first,
then disable SLAVE_EN / clear ADDR_CTRL, synchronize_irq(), W1C
pending ISR, and only then NULL i2c_bus->target and clear
target_active. The old order left IER enabled while target was
being cleared, allowing an in-flight handler to dereference a
target pointer the caller had already freed.
- reg_target() bring-up ordering: assign i2c_bus->target before
enabling SLAVE_EN. Otherwise an IRQ that fires after SLAVE_EN is
set but before the pointer is stored finds target == NULL, exits
without clearing the ISR, and the unmasked event re-fires as an
IRQ storm.
- Use writel() instead of writeb() when staging a TX byte into the
target buffer. The AST2600 buffer SRAM only supports 32-bit
accesses; byte writes are silently dropped (or, on some
revisions, raise a bus fault), so a SLAVE_READ_REQUESTED reply
never reaches the master.
- reg_target() rejects 10-bit client addresses with -EAFNOSUPPORT.
AST2600_I2CS_ADDR1 is only a 7-bit field; without the check, the
high bits of a 10-bit address overflow into the adjacent ADDR2
field and silently corrupt a second target slot.
- Initialise the local `u8 value` to 0 in the target packet IRQ
handler. Its address is passed to i2c_slave_event() for events
such as I2C_SLAVE_STOP / I2C_SLAVE_READ_REQUESTED; a slave
backend that reads the byte before writing would otherwise leak
uninitialised kernel stack.
Changes in v29:
- fix race between unreg_target and IRQ handler.
- move i2cs ier enable from ast2600_i2c_init to probe after master ier enable.
- remove dma/byte transfer, use buffer mode only.
Changes in v28:
- fix typo condication -> condition
- fix compile error, when disable CONFIG_I2C_SLAVE
Changes in v26:
- change int to bool target_operate
- rename target_operate to target_active
- use i2c_bus->target replace require IO
- use WRITE_ONCE replace target_operate write.
---
drivers/i2c/busses/i2c-ast2600.c | 359 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 358 insertions(+), 1 deletion(-)
diff --git a/drivers/i2c/busses/i2c-ast2600.c b/drivers/i2c/busses/i2c-ast2600.c
index a06d0483865e..7e609fdfa1a1 100644
--- a/drivers/i2c/busses/i2c-ast2600.c
+++ b/drivers/i2c/busses/i2c-ast2600.c
@@ -254,6 +254,11 @@ struct ast2600_i2c_bus {
size_t buf_size;
bool multi_master;
void __iomem *buf_base;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* target structure */
+ bool target_active;
+ struct i2c_client *target;
+#endif
};
static void ast2600_i2c_ac_timing_config(struct ast2600_i2c_bus *i2c_bus)
@@ -337,6 +342,249 @@ static int ast2600_i2c_recover_bus(struct ast2600_i2c_bus *i2c_bus)
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static void ast2600_i2c_target_packet_buff_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+ u8 value = 0;
+ int target_rx_len = 0;
+ u32 cmd = 0;
+ int i;
+
+ /* due to controller target is common buffer, need force the master stop not issue */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_CMD_STS) & GENMASK(15, 0)) {
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_IER);
+ writel(readl(i2c_bus->reg_base + AST2600_I2CM_ISR),
+ i2c_bus->reg_base + AST2600_I2CM_ISR);
+ i2c_bus->cmd_err = -EBUSY;
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ complete(&i2c_bus->cmd_complete);
+ writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
+ i2c_bus->reg_base + AST2600_I2CM_IER);
+ }
+
+ /* Handle i2c target timeout condition */
+ if (sts & AST2600_I2CS_INACTIVE_TO) {
+ /* Reset timeout counter */
+ u32 ac_timing = readl(i2c_bus->reg_base + AST2600_I2CC_AC_TIMING) &
+ AST2600_I2CC_AC_TIMING_MASK;
+
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ ac_timing |= AST2600_I2CC_TTIMEOUT(i2c_bus->timeout);
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ writel(TARGET_TRIGGER_CMD, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ WRITE_ONCE(i2c_bus->target_active, false);
+ return;
+ }
+
+ sts &= ~(AST2600_I2CS_PKT_DONE | AST2600_I2CS_PKT_ERROR);
+
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ WRITE_ONCE(i2c_bus->target_active, true);
+
+ switch (sts) {
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_STOP:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ fallthrough;
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD;
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ }
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_RX_BUFF_EN)
+ cmd = 0;
+ else
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_RX_DONE:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE |
+ AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_STOP:
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writel(value, i2c_bus->buf_base);
+ break;
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writel(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA:
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + i2c_bus->buf_size + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ } else {
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_PROCESSED, &value);
+ }
+ writel(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ /* workaround : trigger the cmd twice to fix next state keep 1000000 */
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ break;
+ case AST2600_I2CS_TX_NAK | AST2600_I2CS_STOP:
+ case AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ default:
+ dev_dbg(i2c_bus->dev, "unhandled target isr case %x, sts %x\n", sts,
+ readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+ break;
+ }
+
+ if (cmd)
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if ((sts & AST2600_I2CS_STOP) && !(sts & AST2600_I2CS_SLAVE_PENDING))
+ WRITE_ONCE(i2c_bus->target_active, false);
+}
+
+static int ast2600_i2c_target_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 ier = readl(i2c_bus->reg_base + AST2600_I2CS_IER);
+ u32 isr = readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if (!(isr & ier))
+ return 0;
+
+ /*
+ * Target interrupt coming after controller packet done
+ * So need handle controller first.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_ISR) & AST2600_I2CM_PKT_DONE)
+ return 0;
+
+ isr &= ~(AST2600_I2CS_ADDR_INDICATE_MASK);
+
+ if (AST2600_I2CS_ADDR1_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR1_NAK;
+
+ if (AST2600_I2CS_ADDR2_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR2_NAK;
+
+ if (AST2600_I2CS_ADDR3_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR3_NAK;
+
+ if (AST2600_I2CS_ADDR_MASK & isr)
+ isr &= ~AST2600_I2CS_ADDR_MASK;
+
+ if (AST2600_I2CS_PKT_DONE & isr)
+ ast2600_i2c_target_packet_buff_irq(i2c_bus, isr);
+
+ return 1;
+}
+#endif
+
static int ast2600_i2c_setup_buff_tx(u32 cmd, struct ast2600_i2c_bus *i2c_bus)
{
struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
@@ -479,7 +727,7 @@ static void ast2600_i2c_controller_packet_irq(struct ast2600_i2c_bus *i2c_bus, u
case AST2600_I2CM_TX_ACK:
case AST2600_I2CM_TX_ACK | AST2600_I2CM_NORMAL_STOP:
xfer_len = AST2600_I2CC_GET_TX_BUF_LEN(readl(i2c_bus->reg_base +
- AST2600_I2CC_BUFF_CTRL));
+ AST2600_I2CC_BUFF_CTRL));
i2c_bus->controller_xfer_cnt += xfer_len;
if (i2c_bus->controller_xfer_cnt == msg->len) {
@@ -498,6 +746,20 @@ static void ast2600_i2c_controller_packet_irq(struct ast2600_i2c_bus *i2c_bus, u
}
break;
case AST2600_I2CM_RX_DONE:
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /*
+ * Workaround for controller/target packet mode enable rx done stuck issue
+ * When controller go for first read (RX_DONE), target mode will also effect
+ * Then controller will send nack, not operate anymore.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_PKT_MODE_EN) {
+ u32 target_cmd = readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(target_cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ }
+ fallthrough;
+#endif
case AST2600_I2CM_RX_DONE | AST2600_I2CM_NORMAL_STOP:
xfer_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
AST2600_I2CC_BUFF_CTRL));
@@ -583,6 +845,12 @@ static irqreturn_t ast2600_i2c_bus_irq(int irq, void *dev_id)
{
struct ast2600_i2c_bus *i2c_bus = dev_id;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target) {
+ if (ast2600_i2c_target_irq(i2c_bus))
+ return IRQ_HANDLED;
+ }
+#endif
return IRQ_RETVAL(ast2600_i2c_controller_irq(i2c_bus));
}
@@ -599,12 +867,31 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target_active)
+ return -EBUSY;
+ /*
+ * Controller and target share the same buffer register. A target
+ * transaction can update buffer state asynchronously via IRQ, so block
+ * controller transfers while target is active to avoid buffer corruption.
+ */
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_IER);
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR) || i2c_bus->target_active) {
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+ return -EBUSY;
+ }
+#endif
+
i2c_bus->cmd_err = 0;
i2c_bus->msgs = msgs;
i2c_bus->msgs_index = 0;
i2c_bus->msgs_count = num;
reinit_completion(&i2c_bus->cmd_complete);
ret = ast2600_i2c_do_start(i2c_bus);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* avoid race condition target is wait and controller wait 1st target operate */
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
if (ret)
goto controller_out;
timeout = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
@@ -632,6 +919,9 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
* if the bus is still busy.
*/
if (i2c_bus->multi_master &&
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ !i2c_bus->target_active &&
+#endif
(readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) &
AST2600_I2CC_BUS_BUSY_STS))
ast2600_i2c_recover_bus(i2c_bus);
@@ -667,8 +957,65 @@ static int ast2600_i2c_init(struct ast2600_i2c_bus *i2c_bus)
/* Clear Interrupt */
writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CM_ISR);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CS_ISR);
+#endif
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static int ast2600_i2c_reg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 cmd = TARGET_TRIGGER_CMD;
+
+ if (i2c_bus->target)
+ return -EINVAL;
+
+ if (client->flags & I2C_CLIENT_TEN)
+ return -EAFNOSUPPORT;
+
+ dev_dbg(i2c_bus->dev, "target addr %x\n", client->addr);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ i2c_bus->target = client;
+
+ writel(AST2600_I2CC_SLAVE_EN | readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL),
+ i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ /* Set target addr. */
+ writel(client->addr | AST2600_I2CS_ADDR1_ENABLE,
+ i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ return 0;
+}
+
+static int ast2600_i2c_unreg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 val;
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_IER);
+
+ val = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(val & ~AST2600_I2CC_SLAVE_EN, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ val = readl(i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+ writel(val & ~AST2600_I2CS_ADDR1_MASK, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ synchronize_irq(i2c_bus->irq);
+
+ writel(readl(i2c_bus->reg_base + AST2600_I2CS_ISR),
+ i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ i2c_bus->target = NULL;
+ WRITE_ONCE(i2c_bus->target_active, false);
+
return 0;
}
+#endif
static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
{
@@ -678,6 +1025,10 @@ static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
static const struct i2c_algorithm i2c_ast2600_algorithm = {
.xfer = ast2600_i2c_controller_xfer,
.functionality = ast2600_i2c_functionality,
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ .reg_target = ast2600_i2c_reg_target,
+ .unreg_target = ast2600_i2c_unreg_target,
+#endif
};
static const struct i2c_adapter_quirks ast2600_i2c_quirks = {
@@ -720,6 +1071,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
regmap_write(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, I2CCG_DIV_CTRL);
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ WRITE_ONCE(i2c_bus->target_active, false);
+#endif
i2c_bus->dev = dev;
i2c_bus->multi_master = device_property_read_bool(dev, "multi-master");
@@ -784,6 +1138,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
i2c_bus->reg_base + AST2600_I2CM_IER);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
ret = i2c_add_adapter(&i2c_bus->adap);
if (ret)
--
2.34.1
More information about the linux-arm-kernel
mailing list