[PATCH 3/5] arm64: dts: freescale: imx95-toradex-smarc: move CM7 node to SoC DTSI

[Peng Fan]

On Fri, May 22, 2026 at 04:18:47AM -0700, Laurentiu Mihalcea wrote:
>From: Laurentiu Mihalcea <laurentiu.mihalcea at nxp.com>
>
>The CM7 remoteproc configuration is common to multiple MX95-based
>platforms (e.g. MX95-19x19-EVK, MX95-15x15-FRDM, SMARC-IMX95, etc.).
>Therefore, move the node to the MX95 SoC DTSI. While at it, split the mbox
>channels using <>.
>
>Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea at nxp.com>
>---
> .../boot/dts/freescale/imx95-toradex-smarc.dtsi    | 14 ++++++--------
> arch/arm64/boot/dts/freescale/imx95.dtsi           |  7 +++++++
> 2 files changed, 13 insertions(+), 8 deletions(-)
>
>diff --git a/arch/arm64/boot/dts/freescale/imx95-toradex-smarc.dtsi b/arch/arm64/boot/dts/freescale/imx95-toradex-smarc.dtsi
>index 7d760470201f..c94a63a3bf8f 100644
>--- a/arch/arm64/boot/dts/freescale/imx95-toradex-smarc.dtsi
>+++ b/arch/arm64/boot/dts/freescale/imx95-toradex-smarc.dtsi
>@@ -145,14 +145,6 @@ reg_wifi_en: regulator-wifi-en {
> 		startup-delay-us = <2000>;
> 	};
> 
>-	remoteproc-cm7 {
>-		compatible = "fsl,imx95-cm7";
>-		mboxes = <&mu7 0 1 &mu7 1 1 &mu7 3 1>;
>-		mbox-names = "tx", "rx", "rxdb";
>-		memory-region = <&vdevbuffer>, <&vdev0vring0>, <&vdev0vring1>,
>-				<&vdev1vring0>, <&vdev1vring1>, <&rsc_table>, <&m7_reserved>;
>-	};
>-
> 	reserved-memory {
> 		#address-cells = <2>;
> 		#size-cells = <2>;
>@@ -204,6 +196,12 @@ vdevbuffer: vdevbuffer at 88020000 {
> 	};
> };
> 
>+&cm7 {
>+	memory-region = <&vdevbuffer>, <&vdev0vring0>, <&vdev0vring1>,
>+			<&vdev1vring0>, <&vdev1vring1>, <&rsc_table>, <&m7_reserved>;
>+	status = "okay";
>+};
>+
> /* SMARC GBE0 */
> &enetc_port0 {
> 	pinctrl-names = "default";
>diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
>index 3e35c956a4d7..f8760ac067fa 100644
>--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
>+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
>@@ -272,6 +272,13 @@ opp-1000000000 {
> 		};
> 	};
> 
>+	cm7: remoteproc-cm7 {
>+		compatible = "fsl,imx95-cm7";
>+		mboxes = <&mu7 0 1>, <&mu7 1 1>, <&mu7 3 1>;
>+		mbox-names = "tx", "rx", "rxdb";

Please not put mboxes and mbox-names in dtsi. Some demos may not
require them and boards may use different MUs.

Regards
Peng

>+		status = "disabled";
>+	};
>+
> 	clk_ext1: clock-ext1 {
> 		compatible = "fixed-clock";
> 		#clock-cells = <0>;
>-- 
>2.43.0
>