[PATCH v2 7/7] arm64: dts: qcom: hamoa-iot-evk-camera-imx577: Add DT overlay

[Wenmeng Liu]

Enable IMX577 via CCI on Hamoa EVK Core Kit.

The Hamoa EVK board does not include a camera sensor
by default, this DTSO has enabled the Arducam 12.3MP
IMX577 Mini Camera Module on the CSI-1 interface.

Signed-off-by: Wenmeng Liu <wenmeng.liu at oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  5 ++
 .../boot/dts/qcom/hamoa-iot-evk-camera-imx577.dtso | 74 ++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts         |  7 ++
 3 files changed, 86 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4ba8e73064194926096b98b9556a3207e8f24d72..48536765058a4244a2b895bccc21567d186605bd 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -22,6 +22,11 @@ hamoa-iot-evk-el2-dtbs	:= hamoa-iot-evk.dtb x1-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-lenovo-ideacentre-mini-01q8x10.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk-camera-imx577.dtbo
+
+hamoa-iot-evk-camera-imx577-dtbs	:= hamoa-iot-evk.dtb hamoa-iot-evk-camera-imx577.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk-camera-imx577.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-rdp432-c2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-tplink-archer-ax55-v1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5210-rdp504.dtb
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk-camera-imx577.dtso b/arch/arm64/boot/dts/qcom/hamoa-iot-evk-camera-imx577.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..4a20656f16799d7a9c8fd4ad63ac0989cdc37de4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk-camera-imx577.dtso
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,x1e80100-camcc.h>
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	vreg_cam1_1p8: regulator-cam1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_cam1";
+		startup-delay-us = <1000>;
+		enable-active-high;
+		gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&camss {
+	vdd-csiphy-0p8-supply = <&vreg_l2c_0p8>;
+	vdd-csiphy-1p2-supply = <&vreg_l1c_1p2>;
+
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 1 {
+			reg = <1>;
+
+			csiphy1_ep: endpoint {
+				data-lanes = <0 1 2 3>;
+				remote-endpoint = <&imx577_ep>;
+			};
+		};
+	};
+};
+
+&cci0 {
+	status = "okay";
+};
+
+&cci0_i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	camera at 1a {
+		compatible = "sony,imx577";
+		reg = <0x1a>;
+
+		reset-gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&cam_mclk1_default &cam1_reset_default>;
+		pinctrl-names = "default";
+
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		assigned-clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		assigned-clock-rates = <24000000>;
+
+		dvdd-supply = <&vreg_cam1_1p8>;
+		dovdd-supply = <&vreg_l4m_1p8>;
+
+		port {
+			imx577_ep: endpoint {
+				link-frequencies = /bits/ 64 <600000000>;
+				data-lanes = <0 1 2 3>;
+				remote-endpoint = <&csiphy1_ep>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 460f27dcd6f694c22ab2670d26753ee096ab3682..8cfcf48ee0099d4b505acc3e5662553e77704d5c 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -1320,6 +1320,13 @@ right_tweeter: speaker at 0,1 {
 };
 
 &tlmm {
+	cam1_reset_default: cam1-reset-defult-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	edp_reg_en: edp-reg-en-state {
 		pins = "gpio70";
 		function = "gpio";

-- 
2.34.1