[PATCH v4 5/5] Allwinner: A523: add support for A523 THS0/1 controllers
Chen-Yu Tsai
wens at kernel.org
Tue May 5 07:06:07 PDT 2026
Hi,
On Mon, May 4, 2026 at 1:04 PM Mikhail Kalashnikov <iuncuim at gmail.com> wrote:
The correct format for the patch subject should be:
arm64: dts: allwinner: sun55i: add thermal sensors
> The A523 processor has two temperature controllers, THS0 and THS1.
> THS0 has only one temperature sensor, which is located in the DRAM.
^
"DRAM controller".
>
> THS1 does have 3 sensors:
> ths1_0 - "big" cores
> ths1_1 - "little" cores
> ths1_2 - gpu
>
> Add the thermal sensor configuration and the thermal zones.
> Trips temperature, polling-delay and sustainable-power parameters are
> derived from the manufacturer's BSP.
>
> Signed-off-by: Mikhail Kalashnikov <iuncuim at gmail.com>
> ---
> .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 154 ++++++++++++++++++
> 1 file changed, 154 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
> index 5afa8d92a..288a4710b 100644
> --- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
> @@ -11,6 +11,7 @@
> #include <dt-bindings/reset/sun55i-a523-r-ccu.h>
> #include <dt-bindings/power/allwinner,sun55i-a523-ppu.h>
> #include <dt-bindings/power/allwinner,sun55i-a523-pck-600.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> interrupt-parent = <&gic>;
> @@ -26,6 +27,7 @@ cpu0: cpu at 0 {
> device_type = "cpu";
> reg = <0x000>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu1: cpu at 100 {
> @@ -33,6 +35,7 @@ cpu1: cpu at 100 {
> device_type = "cpu";
> reg = <0x100>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu2: cpu at 200 {
> @@ -40,6 +43,7 @@ cpu2: cpu at 200 {
> device_type = "cpu";
> reg = <0x200>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu3: cpu at 300 {
> @@ -47,6 +51,7 @@ cpu3: cpu at 300 {
> device_type = "cpu";
> reg = <0x300>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu4: cpu at 400 {
> @@ -54,6 +59,7 @@ cpu4: cpu at 400 {
> device_type = "cpu";
> reg = <0x400>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu5: cpu at 500 {
> @@ -61,6 +67,7 @@ cpu5: cpu at 500 {
> device_type = "cpu";
> reg = <0x500>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu6: cpu at 600 {
> @@ -68,6 +75,7 @@ cpu6: cpu at 600 {
> device_type = "cpu";
> reg = <0x600>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
>
> cpu7: cpu at 700 {
> @@ -75,6 +83,7 @@ cpu7: cpu at 700 {
> device_type = "cpu";
> reg = <0x700>;
> enable-method = "psci";
> + #cooling-cells = <2>;
> };
> };
>
> @@ -565,12 +574,46 @@ dma: dma-controller at 3002000 {
> #dma-cells = <1>;
> };
>
> + ths1: thermal-sensor at 2009400 {
> + compatible = "allwinner,sun55i-a523-ths1";
> + reg = <0x02009400 0x400>;
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC1>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_THS>;
> + nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
> + nvmem-cell-names = "calibration",
> + "calibration-second-part";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + ths0: thermal-sensor at 200a000 {
> + compatible = "allwinner,sun55i-a523-ths0";
> + reg = <0x0200a000 0x400>;
> + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC0>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_THS>;
> + nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
> + nvmem-cell-names = "calibration",
> + "calibration-second-part";
> + #thermal-sensor-cells = <0>;
> + };
> +
The device nodes are sorted by base address, so the thermal sensors should
be much further up in this file.
> sid: efuse at 3006000 {
> compatible = "allwinner,sun55i-a523-sid",
> "allwinner,sun50i-a64-sid";
> reg = <0x03006000 0x1000>;
> #address-cells = <1>;
> #size-cells = <1>;
> +
> + ths_calibration0: ths-calibration0 at 38 {
> + reg = <0x38 0x8>;
> + };
> +
> + ths_calibration1: ths-calibration1 at 44 {
> + reg = <0x44 0x8>;
> + };
> };
>
> gic: interrupt-controller at 3400000 {
> @@ -1087,4 +1130,115 @@ npu: npu at 7122000 {
> power-domains = <&ppu PD_NPU>;
> };
> };
> +
> + thermal-zones {
> + cpu0_thermal: cpu0-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <1000>;
> + thermal-sensors = <&ths1 1>;
> + sustainable-power = <1200>;
> +
> + trips {
> + cpu0_threshold: cpu-trip-0 {
> + temperature = <70000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
Please have one empty line between nodes, per the DT coding style.
Same for the other two "trips" nodes.
> + cpu0_target: cpu-trip-1 {
> + temperature = <90000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
> + cpu0_critical: cpu-trip-2 {
> + temperature = <110000>;s
> + type = "critical";
> + hysteresis = <0>;
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu0_target>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + cpu4_thermal: cpu4-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <1000>;
> + thermal-sensors = <&ths1 0>;
> + sustainable-power = <1600>;
> +
> + trips {
> + cpu4_threshold: cpu-trip-0 {
> + temperature = <70000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
> + cpu4_target: cpu-trip-1 {
> + temperature = <90000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
> + cpu4_critical: cpu-trip-2 {
> + temperature = <110000>;
> + type = "critical";
> + hysteresis = <0>;
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu4_target>;
> + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + gpu-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <1000>;
> + thermal-sensors = <&ths1 2>;
> + sustainable-power = <2400>;
> +
> + gpu-trips {
> + gpu_temp_threshold: gpu-trip-0 {
> + temperature = <60000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
> + gpu_temp_target: gpu-trip-1 {
> + temperature = <90000>;
> + type = "passive";
> + hysteresis = <0>;
> + };
> + gpu_temp_critical: gpu-trip-2 {
> + temperature = <110000>;
> + type = "critical";
> + hysteresis = <0>;
> + };
> + };
> + };
> +
> + ddr-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&ths0>;
> +
> + trips {
> + ddr_temp_critical: ddr-trip-0 {
> + temperature = <110000>;
> + type = "critical";
> + hysteresis = <0>;
> + };
> + };
> + };
> + };
> };
> --
> 2.54.0
>
More information about the linux-arm-kernel
mailing list