[PATCH RESEND v4 0/8] can: flexcan: Add NXP S32N79 SoC support

[Ciprian Marian Costea]

On 4/21/2026 1:25 PM, Ciprian Costea wrote:
> From: Ciprian Marian Costea <ciprianmarian.costea at oss.nxp.com>
> 

Hello Marc,

Following up on v4. All comments from v3 have been addressed. Let me
know if there's anything else you'd like changed.

Best Regards,
Ciprian

> This patch series adds FlexCAN support for the NXP S32N79 SoC.
> 
> The S32N79 is an automotive-grade processor from NXP with multiple
> FlexCAN instances. The FlexCAN IP integration on S32N79 differs from
> other SoCs in the interrupt routing - it uses two separate interrupt
> lines:
>    - one interrupt for mailboxes 0-127
>    - one interrupt for bus error detection and device state changes
> 
> The CAN controllers are connected through an irqsteer interrupt
> controller in the RCU (Resource Control Unit) domain.
> 
> This series:
>    1. Splits flexcan_irq() into dedicated handlers for multi-IRQ platforms
>    2. Adds dt-bindings documentation for S32N79 FlexCAN
>    3. Introduces FLEXCAN_QUIRK_IRQ_BERR to handle the two-interrupt
>       configuration
>    4. Adds S32N79 device data and compatible string to the driver
>    5. Adds FlexCAN device tree nodes for S32N79 SoC
>    6. Enables FlexCAN devices on the S32N79-RDB board
> 
> Tested on S32N79-RDB board with CAN and CAN FD communication.
> 
> This is a resend of v4 with no changes.
> 
> v4 -> v3
> - flexcan_chip_interrupts_enable(): disable/enable all IRQ lines
>    (not just dev->irq) during IMASK register writes
> - Split rx/tx masks per mailbox IRQ line (struct flexcan_mb_irq) so
>    each handler on S32G2 only processes its own MB range
> - Added received Acked-by tag on DT bindings patch
> 
> v3 -> v2
> - Split flexcan_irq() into dedicated handlers (flexcan_irq_mb,
>    flexcan_irq_boff, flexcan_irq_berr) to fix duplicate event
>    processing when multiple IRQ lines run concurrently (new patch).
> - Added flexcan_irq_esr() handler composing state + berr for S32N79
> - Ordered quirks used by s32n devtype data by value.
> 
> v2 -> v1
> - Renamed FLEXCAN_QUIRK_NR_IRQ_2 to FLEXCAN_QUIRK_IRQ_BERR to better
> describe the actual hardware feature
> - Appended new quirk at the end
> - Switched from platform_get_irq to platform_get_irq_byname usage
> - Updated interrupt description in dt-bindings
> 
> Ciprian Marian Costea (8):
>    can: flexcan: use dedicated IRQ handlers for multi-IRQ platforms
>    can: flexcan: disable all IRQ lines in
>      flexcan_chip_interrupts_enable()
>    can: flexcan: split rx/tx masks per mailbox IRQ line
>    dt-bindings: can: fsl,flexcan: add NXP S32N79 SoC support
>    can: flexcan: add FLEXCAN_QUIRK_IRQ_BERR quirk
>    can: flexcan: add NXP S32N79 SoC support
>    arm64: dts: s32n79: add FlexCAN nodes
>    arm64: dts: s32n79: enable FlexCAN devices
> 
>   .../bindings/net/can/fsl,flexcan.yaml         |  30 ++-
>   arch/arm64/boot/dts/freescale/s32n79-rdb.dts  |  12 +
>   arch/arm64/boot/dts/freescale/s32n79.dtsi     |  50 ++++
>   drivers/net/can/flexcan/flexcan-core.c        | 249 +++++++++++++++---
>   drivers/net/can/flexcan/flexcan.h             |  12 +-
>   5 files changed, 316 insertions(+), 37 deletions(-)
>