[PATCH] dmaengine: xilinx_dma: Fix CPU stall in xilinx_dma_poll_timeout
Gupta, Suraj
suraj.gupta2 at amd.com
Tue Mar 31 22:23:28 PDT 2026
On 3/31/2026 10:14 PM, Alex Bereza wrote:
> [You don't often get email from alex at bereza.email. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
>
> Caution: This message originated from an External Source. Use proper caution when opening attachments, clicking links, or responding.
>
>
> Currently when calling xilinx_dma_poll_timeout with delay_us=0 and a
> condition that is never fulfilled, the CPU busy-waits for prolonged time
> and the timeout triggers only with a massive delay causing a CPU stall.
>
> This happens due to a huge underestimation of wall clock time in
> poll_timeout_us_atomic. Commit 7349a69cf312 ("iopoll: Do not use
> timekeeping in read_poll_timeout_atomic()") changed the behavior to no
> longer use ktime_get at the expense of underestimation of wall clock
> time which appears to be very large for delay_us=0. Instead of timing
> out after approximately XILINX_DMA_LOOP_COUNT microseconds, the timeout
> takes XILINX_DMA_LOOP_COUNT * 1000 * (time that the overhead of the for
> loop in poll_timeout_us_atomic takes) which is in the range of several
> minutes for XILINX_DMA_LOOP_COUNT=1000000. Fix this by using a non-zero
> value for delay_us. Use delay_us=10 to keep the delay in the hot path of
> starting DMA transfers minimal but still avoid CPU stalls in case of
> unexpected hardware failures.
>
> One-off measurement with delay_us=0 causes the cpu to busy wait around 7
> minutes in the timeout case. After applying this patch with delay_us=10
> the measured timeout was 1053428 microseconds which is roughly
> equivalent to the expected 1000000 microseconds specified in
> XILINX_DMA_POLL_TIMEOUT_US.
>
> Rename XILINX_DMA_LOOP_COUNT to XILINX_DMA_POLL_TIMEOUT_US because the
> former is incorrect. It is a timeout value for polling various register
> bits in microseconds. It is not a loop count. Add a constant
> XILINX_DMA_POLL_DELAY_US for delay_us value.
Please split this change in a new patch.
>
> Fixes: 7349a69cf312 ("iopoll: Do not use timekeeping in read_poll_timeout_atomic()")
This patch doesn't fixes anything in iopoll, please use correct fixes tag.
> Signed-off-by: Alex Bereza <alex at bereza.email>
> ---
> Hi, in addition to this patch I also have a question: what is the point
> of atomically polling for the HALTED or IDLE bit in the stop_transfer
> functions? Does device_terminate_all really need to be callable from
> atomic context? If not, one could switch to polling non-atomically and
> avoid burning CPU cycles.
>
dmaengine_terminate_async(), which directly calls device_terminate_all
can be called from atomic context.
Regards,
Suraj
> As this is my first patch, please feel free to point me in the right
> direction if I am missing anything.
> ---
> drivers/dma/xilinx/xilinx_dma.c | 26 ++++++++++++++++----------
> 1 file changed, 16 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
> index 02a05f215614..8556c357b665 100644
> --- a/drivers/dma/xilinx/xilinx_dma.c
> +++ b/drivers/dma/xilinx/xilinx_dma.c
> @@ -165,8 +165,10 @@
> #define XILINX_DMA_FLUSH_MM2S 2
> #define XILINX_DMA_FLUSH_BOTH 1
>
> -/* Delay loop counter to prevent hardware failure */
> -#define XILINX_DMA_LOOP_COUNT 1000000
> +/* Timeout for polling various registers */
> +#define XILINX_DMA_POLL_TIMEOUT_US 1000000
> +/* Delay between polls (avoid a delay of 0 to prevent CPU stalls) */
> +#define XILINX_DMA_POLL_DELAY_US 10
>
> /* AXI DMA Specific Registers/Offsets */
> #define XILINX_DMA_REG_SRCDSTADDR 0x18
> @@ -1332,8 +1334,9 @@ static int xilinx_dma_stop_transfer(struct xilinx_dma_chan *chan)
>
> /* Wait for the hardware to halt */
> return xilinx_dma_poll_timeout(chan, XILINX_DMA_REG_DMASR, val,
> - val & XILINX_DMA_DMASR_HALTED, 0,
> - XILINX_DMA_LOOP_COUNT);
> + val & XILINX_DMA_DMASR_HALTED,
> + XILINX_DMA_POLL_DELAY_US,
> + XILINX_DMA_POLL_TIMEOUT_US);
> }
>
> /**
> @@ -1347,8 +1350,9 @@ static int xilinx_cdma_stop_transfer(struct xilinx_dma_chan *chan)
> u32 val;
>
> return xilinx_dma_poll_timeout(chan, XILINX_DMA_REG_DMASR, val,
> - val & XILINX_DMA_DMASR_IDLE, 0,
> - XILINX_DMA_LOOP_COUNT);
> + val & XILINX_DMA_DMASR_IDLE,
> + XILINX_DMA_POLL_DELAY_US,
> + XILINX_DMA_POLL_TIMEOUT_US);
> }
>
> /**
> @@ -1364,8 +1368,9 @@ static void xilinx_dma_start(struct xilinx_dma_chan *chan)
>
> /* Wait for the hardware to start */
> err = xilinx_dma_poll_timeout(chan, XILINX_DMA_REG_DMASR, val,
> - !(val & XILINX_DMA_DMASR_HALTED), 0,
> - XILINX_DMA_LOOP_COUNT);
> + !(val & XILINX_DMA_DMASR_HALTED),
> + XILINX_DMA_POLL_DELAY_US,
> + XILINX_DMA_POLL_TIMEOUT_US);
>
> if (err) {
> dev_err(chan->dev, "Cannot start channel %p: %x\n",
> @@ -1780,8 +1785,9 @@ static int xilinx_dma_reset(struct xilinx_dma_chan *chan)
>
> /* Wait for the hardware to finish reset */
> err = xilinx_dma_poll_timeout(chan, XILINX_DMA_REG_DMACR, tmp,
> - !(tmp & XILINX_DMA_DMACR_RESET), 0,
> - XILINX_DMA_LOOP_COUNT);
> + !(tmp & XILINX_DMA_DMACR_RESET),
> + XILINX_DMA_POLL_DELAY_US,
> + XILINX_DMA_POLL_TIMEOUT_US);
>
> if (err) {
> dev_err(chan->dev, "reset timeout, cr %x, sr %x\n",
>
> ---
> base-commit: b7560798466a07d9c3fb011698e92c335ab28baf
> change-id: 20260330-fix-atomic-poll-timeout-regression-4f4e3baf3fd7
>
> Best regards,
> --
> Alex Bereza <alex at bereza.email>
>
>
More information about the linux-arm-kernel
mailing list