[PATCH 1/2] arm64: dts: ti: k3-pinctrl: consistently use tabs for alignment
Rasmus Villemoes
linux at rasmusvillemoes.dk
Fri Mar 27 07:15:12 PDT 2026
Currently, there's a mix of spaces and tabs used for aligning the
bodies of the macros, even within the same block. Use tabs throughout
for consistency.
No functional change; 'git diff -w' produces no output.
Signed-off-by: Rasmus Villemoes <linux at rasmusvillemoes.dk>
---
arch/arm64/boot/dts/ti/k3-pinctrl.h | 78 ++++++++++++++---------------
1 file changed, 39 insertions(+), 39 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-pinctrl.h b/arch/arm64/boot/dts/ti/k3-pinctrl.h
index dc8e03ae74c8..bdccb153e089 100644
--- a/arch/arm64/boot/dts/ti/k3-pinctrl.h
+++ b/arch/arm64/boot/dts/ti/k3-pinctrl.h
@@ -8,15 +8,15 @@
#ifndef DTS_ARM64_TI_K3_PINCTRL_H
#define DTS_ARM64_TI_K3_PINCTRL_H
-#define WKUP_LVL_EN_SHIFT (7)
-#define WKUP_LVL_POL_SHIFT (8)
+#define WKUP_LVL_EN_SHIFT (7)
+#define WKUP_LVL_POL_SHIFT (8)
#define ST_EN_SHIFT (14)
#define PULLUDEN_SHIFT (16)
#define PULLTYPESEL_SHIFT (17)
#define RXACTIVE_SHIFT (18)
-#define DRV_STR_SHIFT (19)
-#define ISO_OVERRIDE_EN_SHIFT (22)
-#define ISO_BYPASS_EN_SHIFT (23)
+#define DRV_STR_SHIFT (19)
+#define ISO_OVERRIDE_EN_SHIFT (22)
+#define ISO_BYPASS_EN_SHIFT (23)
#define DEBOUNCE_SHIFT (11)
#define FORCE_DS_EN_SHIFT (15)
#define DS_EN_SHIFT (24)
@@ -24,7 +24,7 @@
#define DS_OUT_VAL_SHIFT (26)
#define DS_PULLUD_EN_SHIFT (27)
#define DS_PULLTYPE_SEL_SHIFT (28)
-#define WKUP_EN_SHIFT (29)
+#define WKUP_EN_SHIFT (29)
/* Schmitt trigger configuration */
#define ST_DISABLE (0 << ST_EN_SHIFT)
@@ -39,28 +39,28 @@
#define INPUT_EN (1 << RXACTIVE_SHIFT)
#define INPUT_DISABLE (0 << RXACTIVE_SHIFT)
-#define DS_PULL_DISABLE (1 << DS_PULLUD_EN_SHIFT)
-#define DS_PULL_ENABLE (0 << DS_PULLUD_EN_SHIFT)
+#define DS_PULL_DISABLE (1 << DS_PULLUD_EN_SHIFT)
+#define DS_PULL_ENABLE (0 << DS_PULLUD_EN_SHIFT)
-#define DS_PULL_UP (1 << DS_PULLTYPE_SEL_SHIFT | DS_PULL_ENABLE)
-#define DS_PULL_DOWN (0 << DS_PULLTYPE_SEL_SHIFT | DS_PULL_ENABLE)
+#define DS_PULL_UP (1 << DS_PULLTYPE_SEL_SHIFT | DS_PULL_ENABLE)
+#define DS_PULL_DOWN (0 << DS_PULLTYPE_SEL_SHIFT | DS_PULL_ENABLE)
-#define DS_STATE_EN (1 << DS_EN_SHIFT)
-#define DS_STATE_DISABLE (0 << DS_EN_SHIFT)
+#define DS_STATE_EN (1 << DS_EN_SHIFT)
+#define DS_STATE_DISABLE (0 << DS_EN_SHIFT)
-#define DS_INPUT_EN (1 << DS_OUT_DIS_SHIFT | DS_STATE_EN)
-#define DS_INPUT_DISABLE (0 << DS_OUT_DIS_SHIFT | DS_STATE_EN)
+#define DS_INPUT_EN (1 << DS_OUT_DIS_SHIFT | DS_STATE_EN)
+#define DS_INPUT_DISABLE (0 << DS_OUT_DIS_SHIFT | DS_STATE_EN)
-#define DS_OUT_VALUE_ZERO (0 << DS_OUT_VAL_SHIFT)
-#define DS_OUT_VALUE_ONE (1 << DS_OUT_VAL_SHIFT)
+#define DS_OUT_VALUE_ZERO (0 << DS_OUT_VAL_SHIFT)
+#define DS_OUT_VALUE_ONE (1 << DS_OUT_VAL_SHIFT)
/* Configuration to enable wake-up on pin activity */
-#define WKUP_ENABLE (1 << WKUP_EN_SHIFT)
-#define WKUP_DISABLE (0 << WKUP_EN_SHIFT)
-#define WKUP_ON_LEVEL (1 << WKUP_LVL_EN_SHIFT)
-#define WKUP_ON_EDGE (0 << WKUP_LVL_EN_SHIFT)
-#define WKUP_LEVEL_LOW (0 << WKUP_LVL_POL_SHIFT)
-#define WKUP_LEVEL_HIGH (1 << WKUP_LVL_POL_SHIFT)
+#define WKUP_ENABLE (1 << WKUP_EN_SHIFT)
+#define WKUP_DISABLE (0 << WKUP_EN_SHIFT)
+#define WKUP_ON_LEVEL (1 << WKUP_LVL_EN_SHIFT)
+#define WKUP_ON_EDGE (0 << WKUP_LVL_EN_SHIFT)
+#define WKUP_LEVEL_LOW (0 << WKUP_LVL_POL_SHIFT)
+#define WKUP_LEVEL_HIGH (1 << WKUP_LVL_POL_SHIFT)
/* Only these macros are expected be used directly in device tree files */
#define PIN_OUTPUT (INPUT_DISABLE | PULL_DISABLE)
@@ -82,14 +82,14 @@
#define PIN_DEBOUNCE_CONF5 (5 << DEBOUNCE_SHIFT)
#define PIN_DEBOUNCE_CONF6 (6 << DEBOUNCE_SHIFT)
-#define PIN_DRIVE_STRENGTH_NOMINAL (0 << DRV_STR_SHIFT)
-#define PIN_DRIVE_STRENGTH_SLOW (1 << DRV_STR_SHIFT)
-#define PIN_DRIVE_STRENGTH_FAST (2 << DRV_STR_SHIFT)
+#define PIN_DRIVE_STRENGTH_NOMINAL (0 << DRV_STR_SHIFT)
+#define PIN_DRIVE_STRENGTH_SLOW (1 << DRV_STR_SHIFT)
+#define PIN_DRIVE_STRENGTH_FAST (2 << DRV_STR_SHIFT)
#define PIN_DS_FORCE_DISABLE (0 << FORCE_DS_EN_SHIFT)
#define PIN_DS_FORCE_ENABLE (1 << FORCE_DS_EN_SHIFT)
-#define PIN_DS_ISO_OVERRIDE_DISABLE (0 << ISO_OVERRIDE_EN_SHIFT)
-#define PIN_DS_ISO_OVERRIDE_ENABLE (1 << ISO_OVERRIDE_EN_SHIFT)
+#define PIN_DS_ISO_OVERRIDE_DISABLE (0 << ISO_OVERRIDE_EN_SHIFT)
+#define PIN_DS_ISO_OVERRIDE_ENABLE (1 << ISO_OVERRIDE_EN_SHIFT)
#define PIN_DS_OUT_ENABLE (0 << DS_OUT_DIS_SHIFT)
#define PIN_DS_OUT_DISABLE (1 << DS_OUT_DIS_SHIFT)
#define PIN_DS_OUT_VALUE_ZERO (0 << DS_OUT_VAL_SHIFT)
@@ -98,18 +98,18 @@
#define PIN_DS_PULLUD_DISABLE (1 << DS_PULLUD_EN_SHIFT)
#define PIN_DS_PULL_DOWN (0 << DS_PULLTYPE_SEL_SHIFT)
#define PIN_DS_PULL_UP (1 << DS_PULLTYPE_SEL_SHIFT)
-#define PIN_DS_ISO_BYPASS (1 << ISO_BYPASS_EN_SHIFT)
-#define PIN_DS_ISO_BYPASS_DISABLE (0 << ISO_BYPASS_EN_SHIFT)
-
-#define PIN_DS_OUTPUT_LOW (DS_INPUT_DISABLE | DS_OUT_VALUE_ZERO)
-#define PIN_DS_OUTPUT_HIGH (DS_INPUT_DISABLE | DS_OUT_VALUE_ONE)
-#define PIN_DS_INPUT (DS_INPUT_EN | DS_PULL_DISABLE)
-#define PIN_DS_INPUT_PULLUP (DS_INPUT_EN | DS_PULL_UP)
-#define PIN_DS_INPUT_PULLDOWN (DS_INPUT_EN | DS_PULL_DOWN)
-
-#define PIN_WKUP_EN_LEVEL_LOW (WKUP_ENABLE | WKUP_ON_LEVEL | WKUP_LEVEL_LOW)
-#define PIN_WKUP_EN_LEVEL_HIGH (WKUP_ENABLE | WKUP_ON_LEVEL | WKUP_LEVEL_HIGH)
-#define PIN_WKUP_EN (WKUP_ENABLE | WKUP_ON_EDGE)
+#define PIN_DS_ISO_BYPASS (1 << ISO_BYPASS_EN_SHIFT)
+#define PIN_DS_ISO_BYPASS_DISABLE (0 << ISO_BYPASS_EN_SHIFT)
+
+#define PIN_DS_OUTPUT_LOW (DS_INPUT_DISABLE | DS_OUT_VALUE_ZERO)
+#define PIN_DS_OUTPUT_HIGH (DS_INPUT_DISABLE | DS_OUT_VALUE_ONE)
+#define PIN_DS_INPUT (DS_INPUT_EN | DS_PULL_DISABLE)
+#define PIN_DS_INPUT_PULLUP (DS_INPUT_EN | DS_PULL_UP)
+#define PIN_DS_INPUT_PULLDOWN (DS_INPUT_EN | DS_PULL_DOWN)
+
+#define PIN_WKUP_EN_LEVEL_LOW (WKUP_ENABLE | WKUP_ON_LEVEL | WKUP_LEVEL_LOW)
+#define PIN_WKUP_EN_LEVEL_HIGH (WKUP_ENABLE | WKUP_ON_LEVEL | WKUP_LEVEL_HIGH)
+#define PIN_WKUP_EN (WKUP_ENABLE | WKUP_ON_EDGE)
/* Default mux configuration for gpio-ranges to use with pinctrl */
#define PIN_GPIO_RANGE_IOPAD (PIN_INPUT | 7)
--
2.53.0
More information about the linux-arm-kernel
mailing list