[PATCH v3 4/5] arm64: dts: freescale: add initial device tree for TQMa8x
Frank Li
Frank.li at nxp.com
Tue Mar 24 08:38:49 PDT 2026
On Thu, Feb 26, 2026 at 04:38:53PM +0100, Alexander Stein wrote:
> This adds support for TQMa8QM module on MBa8x board, based on i.MX8 SoC.
>
> Signed-off-by: Alexander Stein <alexander.stein at ew.tq-group.com>
> ---
I picked other patches in serial, I found missed this one when go through
patchworks.
> +
> + fan0: pwm-fan {
> + compatible = "pwm-fan";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwmfan>;
> + fan-supply = <®_pwm_fan>;
> + #cooling-cells = <2>;
> + /* typical 25 kHz -> 40.000 nsec */
> + pwms = <&lsio_pwm3 0 40000 PWM_POLARITY_INVERTED>;
> + cooling-levels = <0 32 64 128 196 240>;
> + pulses-per-revolution = <2>;
> + interrupt-parent = <&lsio_gpio2>;
> + interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> + };
Please order by node name.
Can you try run my tools dt-format for new dts file, which speed up the
flow.
Frank
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpiokeys>;
> + autorepeat;
> +
> + switch-1 {
> + label = "SWITCH_A";
> + linux,code = <BTN_0>;
> + gpios = <&lsio_gpio2 11 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> +
> + switch-2 {
> + label = "SWITCH_B";
> + linux,code = <BTN_1>;
> + gpios = <&lsio_gpio1 0 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpioled>;
> +
> + user-led0 {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_HEARTBEAT;
> + gpios = <&lsio_gpio5 20 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + user-led1 {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&lsio_gpio5 19 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> + };
> +
> + reg_mba8x_v3v3: regulator-mba8x-v3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "V_3V3_MB";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_mba8x_12v: regulator-mba8x-12v {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_mba8x_12v>;
> + regulator-name = "MBa8x-V12";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + enable-active-high;
> + gpio = <&lsio_gpio1 2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_pwm_fan: regulator-pwm-fan {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_regpwmfan>;
> + regulator-name = "FAN_PWR";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + gpio = <&lsio_gpio2 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <®_mba8x_12v>;
> + };
> +
> + reg_usb_phy: regulator-usb-phy {
> + compatible = "regulator-fixed";
> + regulator-max-microvolt = <3000000>;
> + regulator-min-microvolt = <3000000>;
> + regulator-name = "usb-phy-dummy";
> + };
> +
> + reg_v1v5_pcie: regulator-v1v5-pcie {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_pcie_v1v5>;
> + regulator-name = "V_1V5_MPCIE";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + vin-supply = <®_mba8x_v3v3>;
> + enable-active-high;
> + gpio = <&lsio_gpio0 31 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + };
> +
> + reg_vref_v1v8: regulator-vref-v1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VREF_V1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_v1v8: regulator-v1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "MBa8x-V1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + reg_v3v3_pcie: regulator-v3v3-pcie {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_pcie_v3v3>;
> + regulator-name = "V_3V3_MPCIE";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <®_mba8x_v3v3>;
> + enable-active-high;
> + gpio = <&lsio_gpio1 1 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + };
> +
> + reg_v3v3_sd: regulator-v3v3-sd {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_v3v3_sd>;
> + regulator-name = "V3V3_SD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <®_mba8x_v3v3>;
> + gpio = <&lsio_gpio4 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + off-on-delay-us = <200000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + decoder_boot: decoder-boot at 84000000 {
> + reg = <0 0x84000000 0 0x2000000>;
> + no-map;
> + };
> +
> + encoder1_boot: encoder1-boot at 86000000 {
> + reg = <0 0x86000000 0 0x200000>;
> + no-map;
> + };
> +
> + encoder2_boot: encoder2-boot at 86200000 {
> + reg = <0 0x86200000 0 0x200000>;
> + no-map;
> + };
> +
> + decoder_rpc: decoder-rpc at 92000000 {
> + reg = <0 0x92000000 0 0x100000>;
> + no-map;
> + };
> +
> + encoder1_rpc: encoder1-rpc at 92100000 {
> + reg = <0 0x92100000 0 0x700000>;
> + no-map;
> + };
> +
> + encoder2_rpc: encoder1-rpc at 92800000 {
> + reg = <0 0x92800000 0 0x700000>;
> + no-map;
> + };
> +
> + /*
> + * global autoconfigured region for contiguous allocations
> + * must not exceed memory size and region
> + */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + size = <0 0x3c000000>;
> + alloc-ranges = <0 0x96000000 0 0x3c000000>;
> + linux,cma-default;
> + };
> + };
> +
> + sound {
> + compatible = "fsl,imx-audio-tlv320aic32x4";
> + model = "tqm-tlv320aic32";
> + ssi-controller = <&sai1>;
> + audio-codec = <&tlv320aic3x04>;
> + audio-routing =
> + "IN3_L", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "IN1_L", "Line In Jack",
> + "IN1_R", "Line In Jack",
> + "Line Out Jack", "LOL",
> + "Line Out Jack", "LOR";
> + };
> +
> + sound-hdmi {
> + compatible = "fsl,imx-audio-hdmi";
> + model = "imx-audio-dp";
> + audio-cpu = <&sai5>;
> + hdmi-out;
> + };
> +
> + thermal-zones {
> + cpu0-thermal {
> + trips {
> + soc_active0_0: trip-active0 {
> + temperature = <40000>;
> + hysteresis = <5000>;
> + type = "active";
> + };
> +
> + soc_active0_1: trip-active1 {
> + temperature = <48000>;
> + hysteresis = <3000>;
> + type = "active";
> + };
> +
> + soc_active0_2: trip-active2 {
> + temperature = <60000>;
> + hysteresis = <10000>;
> + type = "active";
> + };
> + };
> +
> + cooling-maps {
> + map1 {
> + trip = <&soc_active0_0>;
> + cooling-device = <&fan0 1 1>;
> + };
> +
> + map2 {
> + trip = <&soc_active0_1>;
> + cooling-device = <&fan0 2 2>;
> + };
> +
> + map3 {
> + trip = <&soc_active0_2>;
> + cooling-device = <&fan0 3 3>;
> + };
> + };
> + };
> +
> + cpu1-thermal {
> + trips {
> + soc_active1_0: trip-active0 {
> + temperature = <40000>;
> + hysteresis = <5000>;
> + type = "active";
> + };
> +
> + soc_active1_1: trip-active1 {
> + temperature = <48000>;
> + hysteresis = <3000>;
> + type = "active";
> + };
> +
> + soc_active1_2: trip-active2 {
> + temperature = <60000>;
> + hysteresis = <10000>;
> + type = "active";
> + };
> + };
> +
> + cooling-maps {
> + map1 {
> + trip = <&soc_active1_0>;
> + cooling-device = <&fan0 1 1>;
> + };
> +
> + map2 {
> + trip = <&soc_active1_1>;
> + cooling-device = <&fan0 2 2>;
> + };
> +
> + map3 {
> + trip = <&soc_active1_2>;
> + cooling-device = <&fan0 3 3>;
> + };
> + };
> + };
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + nvmem-cells = <&fec_mac0>;
> + nvmem-cell-names = "mac-address";
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ethphy0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,dp83867-rxctrl-strap-quirk;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + reset-gpios = <&lsio_gpio2 6 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <500000>;
> + reset-deassert-us = <50000>;
> + enet-phy-lane-no-swap;
> + interrupt-parent = <&lsio_gpio2>;
> + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec2>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy3>;
> + nvmem-cells = <&fec_mac1>;
> + nvmem-cell-names = "mac-address";
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy3: ethernet-phy at 3 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ethphy3>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,dp83867-rxctrl-strap-quirk;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + reset-gpios = <&lsio_gpio2 4 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <500000>;
> + reset-deassert-us = <50000>;
> + enet-phy-lane-no-swap;
> + };
> + };
> +};
> +
> +&flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + status = "okay";
> +};
> +
> +&flexcan2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + status = "okay";
> +};
> +
> +&hsio_phy {
> + fsl,hsio-cfg = "pciea-pcieb-sata";
> + fsl,refclk-pad-mode = "input";
> + status = "okay";
> +};
> +
> +/* no refclock gating */
> +&hsio_refa_clk {
> + compatible = "fixed-factor-clock";
> + clocks = <&pcieclk 0>;
> + clock-div = <1>;
> + clock-mult = <1>;
> + /delete-property/ enable-gpios;
> +};
> +
> +&hsio_refb_clk {
> + compatible = "fixed-factor-clock";
> + clocks = <&pcieclk 0>;
> + clock-div = <1>;
> + clock-mult = <1>;
> + /delete-property/ enable-gpios;
> +};
> +
> +&i2c1 {
> + tlv320aic3x04: audio-codec at 18 {
> + compatible = "ti,tlv320aic32x4";
> + reg = <0x18>;
> + clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
> + clock-names = "mclk";
> + assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
> + <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
> + <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
> + <&mclkout0_lpcg IMX_LPCG_CLK_0>;
> + assigned-clock-rates = <786432000>, <49152000>, <12288000>, <12288000>;
> + ldoin-supply = <®_mba8x_v3v3>;
> + iov-supply = <®_v1v8>;
> + };
> +
> + sensor1: temperature-sensor at 1c {
> + compatible = "nxp,se97b", "jedec,jc-42.4-temp";
> + reg = <0x1c>;
> + };
> +
> + eeprom2: eeprom at 54 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + reg = <0x54>;
> + pagesize = <16>;
> + vcc-supply = <®_mba8x_v3v3>;
> + };
> +
> + pcieclk: clock-generator at 68 {
> + compatible = "renesas,9fgv0441";
> + reg = <0x68>;
> + clocks = <&clk_xtal25>;
> + #clock-cells = <1>;
> + };
> +};
> +
> +&lpspi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpspi0 &pinctrl_lpspi0_cs>;
> + cs-gpios = <&lsio_gpio3 5 GPIO_ACTIVE_LOW>, <&lsio_gpio3 6 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&lpspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpspi1 &pinctrl_lpspi1_cs>;
> + cs-gpios = <&lsio_gpio3 24 GPIO_ACTIVE_LOW>, <&lsio_gpio3 25 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&lpspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpspi2 &pinctrl_lpspi2_cs>;
> + cs-gpios = <&lsio_gpio3 10 GPIO_ACTIVE_LOW>, <&lsio_gpio3 11 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&lpuart0 { /* console */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpuart0>;
> + status = "okay";
> +};
> +
> +&lpuart1 { /* X62 pin header */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpuart1>;
> + status = "okay";
> +};
> +
> +&lpuart2 { /* mikroBUS */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lpuart2>;
> + status = "okay";
> +};
> +
> +&lsio_gpio2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio2>;
> + gpio-line-names = "", "", "", "",
> + "", "PCIE0_DISABLE#", "", "";
> +
> + pcie0-wdisable1-hog {
> + gpio-hog;
> + gpios = <5 0>;
> + output-high;
> + line-name = "PCIE0_DISABLE#";
> + };
> +
> + pcie-clk-pd-hog {
> + gpio-hog;
> + gpios = <10 0>;
> + output-high;
> + line-name = "PCIE_CLK_PD#";
> + };
> +};
> +
> +&lsio_pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lsio_pwm3>;
> + status = "okay";
> +};
> +
> +&pciea {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pciea>;
> + phys = <&hsio_phy 0 PHY_TYPE_PCIE 0>;
> + phy-names = "pcie-phy";
> + reset-gpio = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&pcieb {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcieb>;
> + phys = <&hsio_phy 1 PHY_TYPE_PCIE 1>;
> + phy-names = "pcie-phy";
> + reset-gpio = <&lsio_gpio5 0 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&sai1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai1>;
> + assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
> + <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
> + <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
> + <&sai1_lpcg IMX_LPCG_CLK_0>;
> + assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
> + status = "okay";
> +};
> +
> +&sai5 {
> + status = "okay";
> +};
> +
> +&sai5_lpcg {
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> +};
> +
> +&usbphy1 {
> + phy-3p0-supply = <®_usb_phy>;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg1>;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + power-active-high;
> + over-current-active-low;
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb3_phy {
> + status = "okay";
> +};
> +
> +&usbotg3 {
> + /* over-current disabled by default */
> + status = "okay";
> +};
> +
> +&usbotg3_cdns3 {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbhub>;
> + status = "okay";
> +
> + hub_2_0: hub at 1 {
> + compatible = "usb451,8142";
> + reg = <1>;
> + peer-hub = <&hub_3_0>;
> + reset-gpios = <&lsio_gpio2 7 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_mba8x_v3v3>;
> + };
> +
> + hub_3_0: hub at 2 {
> + compatible = "usb451,8140";
> + reg = <2>;
> + peer-hub = <&hub_2_0>;
> + reset-gpios = <&lsio_gpio2 7 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_mba8x_v3v3>;
> + };
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&lsio_gpio5 22 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>;
> + vmmc-supply = <®_v3v3_sd>;
> + no-mmc;
> + no-sdio;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio>;
> +
> + pinctrl_adc0: adc0grp {
> + fsl,pins = <IMX8QM_ADC_IN1_DMA_ADC0_IN1 0x02000060>,
> + <IMX8QM_ADC_IN2_DMA_ADC0_IN2 0x02000060>;
> + };
> +
> + pinctrl_ethphy0: ethphy0grp {
> + fsl,pins = <IMX8QM_ESAI1_SCKR_LSIO_GPIO2_IO06 0x00000041>,
> + <IMX8QM_ESAI1_TX0_LSIO_GPIO2_IO08 0x00000021>;
> + };
> +
> + pinctrl_ethphy3: ethphy3grp {
> + fsl,pins = <IMX8QM_ESAI1_FSR_LSIO_GPIO2_IO04 0x00000041>;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD 0x000014a0>,
> + <IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000041>,
> + <IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO 0x06000041>,
> + <IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x00000041>,
> + <IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x00000041>,
> + <IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x00000041>,
> + <IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x00000041>,
> + <IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x00000041>,
> + <IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x00000041>,
> + <IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x00000040>,
> + <IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x00000040>,
> + <IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x00000040>,
> + <IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x00000040>,
> + <IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x00000040>,
> + <IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x00000040>;
> + };
> +
> + pinctrl_fec2: fec2grp {
> + fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0>,
> + <IMX8QM_ENET1_MDC_CONN_ENET1_MDC 0x06000041>,
> + <IMX8QM_ENET1_MDIO_CONN_ENET1_MDIO 0x06000041>,
> + <IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000041>,
> + <IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000041>,
> + <IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000041>,
> + <IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000041>,
> + <IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000041>,
> + <IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000041>,
> + <IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000040>,
> + <IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000040>,
> + <IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000040>,
> + <IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000040>,
> + <IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000040>,
> + <IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000040>;
> + };
> +
> + pinctrl_flexcan1: flexcan0grp {
> + fsl,pins = <IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x00000021>,
> + <IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX 0x00000021>;
> + };
> +
> + pinctrl_flexcan2: flexcan1grp {
> + fsl,pins = <IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX 0x00000021>,
> + <IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX 0x00000021>;
> + };
> +
> + pinctrl_gpio: pingpiogrp {
> + fsl,pins = /* GPIO0_05 on X62:26 */
> + <IMX8QM_SIM0_GPIO0_00_LSIO_GPIO0_IO05 0x00000021>,
> + /* GPIO1_14 on X64:21 */
> + <IMX8QM_LVDS1_I2C1_SCL_LSIO_GPIO1_IO14 0x00000021>,
> + /* GPIO1_15 on X64:23 */
> + <IMX8QM_LVDS1_I2C1_SDA_LSIO_GPIO1_IO15 0x00000021>,
> + /* GPIO2_17 on X63:37 */
> + <IMX8QM_SPI3_SCK_LSIO_GPIO2_IO17 0x00000021>,
> + /* GPIO2_21 on X63:39 */
> + <IMX8QM_SPI3_CS1_LSIO_GPIO2_IO21 0x00000021>,
> + /* GPIO4_12 on X61:24 */
> + <IMX8QM_USDHC2_CD_B_LSIO_GPIO4_IO12 0x00000021>,
> + /* GPIO4_11 on X61:26 */
> + <IMX8QM_USDHC2_WP_LSIO_GPIO4_IO11 0x00000021>,
> + /* GPIO4_10 on X61:28 */
> + <IMX8QM_USDHC2_VSELECT_LSIO_GPIO4_IO10 0x00000021>,
> + /* GPIO4_09 on X61:30 */
> + <IMX8QM_USDHC2_RESET_B_LSIO_GPIO4_IO09 0x00000021>,
> + /* GPIO5_23 on X62:24 */
> + <IMX8QM_USDHC1_STROBE_LSIO_GPIO5_IO23 0x00000021>,
> + /* GPIO5_24 on X61:15 */
> + <IMX8QM_USDHC2_CLK_LSIO_GPIO5_IO24 0x00000021>,
> + /* GPIO5_25 on X61:17 */
> + <IMX8QM_USDHC2_CMD_LSIO_GPIO5_IO25 0x00000021>,
> + /* GPIO5_26 on X61:19 */
> + <IMX8QM_USDHC2_DATA0_LSIO_GPIO5_IO26 0x00000021>,
> + /* GPIO5_27 on X61:21 */
> + <IMX8QM_USDHC2_DATA1_LSIO_GPIO5_IO27 0x00000021>,
> + /* GPIO5_28 on X61:23 */
> + <IMX8QM_USDHC2_DATA2_LSIO_GPIO5_IO28 0x00000021>,
> + /* GPIO5_29 on X61:25 */
> + <IMX8QM_USDHC2_DATA3_LSIO_GPIO5_IO29 0x00000021>;
> + };
> +
> + pinctrl_gpio2: gpio2grp {
> + fsl,pins = <IMX8QM_ESAI1_FST_LSIO_GPIO2_IO05 0x00000021>,
> + <IMX8QM_ESAI1_TX2_RX3_LSIO_GPIO2_IO10 0x00000021>;
> + };
> +
> + pinctrl_gpiokeys: gpiokeysgrp {
> + fsl,pins = <IMX8QM_ESAI1_TX3_RX2_LSIO_GPIO2_IO11 0x00000021>,
> + <IMX8QM_SCU_GPIO0_04_LSIO_GPIO1_IO00 0x00000021>;
> + };
> +
> + pinctrl_gpioled: gpioledgrp {
> + fsl,pins = <IMX8QM_USDHC1_DATA4_LSIO_GPIO5_IO19 0x00000021>,
> + <IMX8QM_USDHC1_DATA5_LSIO_GPIO5_IO20 0x00000021>;
> + };
> +
> + pinctrl_lpspi0: lpspi0grp {
> + fsl,pins = <IMX8QM_SPI0_SCK_DMA_SPI0_SCK 0x0600004d>,
> + <IMX8QM_SPI0_SDO_DMA_SPI0_SDO 0x0600004d>,
> + <IMX8QM_SPI0_SDI_DMA_SPI0_SDI 0x0600004d>;
> + };
> +
> + pinctrl_lpspi0_cs: lpspi0csgrp {
> + fsl,pins = <IMX8QM_SPI0_CS0_LSIO_GPIO3_IO05 0x00000021>,
> + <IMX8QM_SPI0_CS1_LSIO_GPIO3_IO06 0x00000021>;
> + };
> +
> + pinctrl_lpspi1: lpspi1grp {
> + fsl,pins = <IMX8QM_ADC_IN3_DMA_SPI1_SCK 0x0600004d>,
> + <IMX8QM_ADC_IN4_DMA_SPI1_SDO 0x0600004d>,
> + <IMX8QM_ADC_IN5_DMA_SPI1_SDI 0x0600004d>;
> + };
> +
> + pinctrl_lpspi1_cs: lpspi1csgrp {
> + fsl,pins = <IMX8QM_ADC_IN6_LSIO_GPIO3_IO24 0x00000021>,
> + <IMX8QM_ADC_IN7_LSIO_GPIO3_IO25 0x00000021>;
> + };
> +
> + pinctrl_lpspi2: lpspi2grp {
> + fsl,pins = <IMX8QM_SPI2_SCK_DMA_SPI2_SCK 0x0600004d>,
> + <IMX8QM_SPI2_SDO_DMA_SPI2_SDO 0x0600004d>,
> + <IMX8QM_SPI2_SDI_DMA_SPI2_SDI 0x0600004d>;
> + };
> +
> + pinctrl_lpspi2_cs: lpspi2sgrp {
> + fsl,pins = <IMX8QM_SPI2_CS0_LSIO_GPIO3_IO10 0x00000021>,
> + <IMX8QM_SPI2_CS1_LSIO_GPIO3_IO11 0x00000021>;
> + };
> +
> + pinctrl_lpuart0: lpuart0grp {
> + fsl,pins = <IMX8QM_UART0_RX_DMA_UART0_RX 0x06000021>,
> + <IMX8QM_UART0_TX_DMA_UART0_TX 0x06000021>,
> + <IMX8QM_UART0_CTS_B_DMA_UART0_CTS_B 0x00000021>,
> + <IMX8QM_UART0_RTS_B_DMA_UART0_RTS_B 0x00000021>;
> + };
> +
> + pinctrl_lpuart1: lpuart1grp {
> + fsl,pins = <IMX8QM_UART1_RX_DMA_UART1_RX 0x06000021>,
> + <IMX8QM_UART1_TX_DMA_UART1_TX 0x06000021>,
> + <IMX8QM_UART1_CTS_B_DMA_UART1_CTS_B 0x00000021>,
> + <IMX8QM_UART1_RTS_B_DMA_UART1_RTS_B 0x00000021>;
> + };
> +
> + pinctrl_lpuart2: lpuart2grp {
> + fsl,pins = <IMX8QM_LVDS0_I2C1_SDA_DMA_UART2_RX 0x06000021>,
> + <IMX8QM_LVDS0_I2C1_SCL_DMA_UART2_TX 0x06000021>;
> + };
> +
> + pinctrl_lsio_pwm3: lsiopwm3grp {
> + fsl,pins = <IMX8QM_GPT0_COMPARE_LSIO_PWM3_OUT 0x00000021>;
> + };
> +
> + pinctrl_pciea: pcieagrp {
> + fsl,pins = <IMX8QM_PCIE_CTRL0_PERST_B_LSIO_GPIO4_IO29 0x06000021>,
> + <IMX8QM_PCIE_CTRL0_CLKREQ_B_HSIO_PCIE0_CLKREQ_B 0x06000021>,
> + <IMX8QM_PCIE_CTRL0_WAKE_B_LSIO_GPIO4_IO28 0x04000021>;
> + };
> +
> + pinctrl_pcieb: pciebgrp {
> + fsl,pins = <IMX8QM_PCIE_CTRL1_PERST_B_LSIO_GPIO5_IO00 0x06000021>,
> + <IMX8QM_PCIE_CTRL1_CLKREQ_B_HSIO_PCIE1_CLKREQ_B 0x06000021>,
> + <IMX8QM_PCIE_CTRL1_WAKE_B_LSIO_GPIO4_IO31 0x04000021>;
> + };
> +
> + pinctrl_pwmfan: pwmfangrp {
> + fsl,pins = <IMX8QM_SPI3_CS0_LSIO_GPIO2_IO20 0x30>;
> + };
> +
> + pinctrl_reg_mba8x_12v: mba12vgrp {
> + fsl,pins = <IMX8QM_SCU_GPIO0_06_LSIO_GPIO1_IO02 0x00000021>;
> + };
> +
> + pinctrl_reg_pcie_v1v5: regpcie1v5grp {
> + fsl,pins = <IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x00000021>;
> + };
> +
> + pinctrl_reg_pcie_v3v3: regpcie3v3grp {
> + fsl,pins = <IMX8QM_SCU_GPIO0_05_LSIO_GPIO1_IO01 0x00000021>;
> + };
> +
> + pinctrl_regpwmfan: regpwmfangrp {
> + fsl,pins = <IMX8QM_ESAI1_TX4_RX1_LSIO_GPIO2_IO12 0x00000021>;
> + };
> +
> + pinctrl_reg_v3v3_sd: reg3v3sdgrp {
> + fsl,pins = <IMX8QM_USDHC1_RESET_B_LSIO_GPIO4_IO07 0x00000021>;
> + };
> +
> + pinctrl_sai1: sai1grp {
> + fsl,pins = <IMX8QM_SAI1_RXD_AUD_SAI1_RXD 0x06000041>,
> + <IMX8QM_SAI1_RXC_AUD_SAI1_RXC 0x06000041>,
> + <IMX8QM_SAI1_RXFS_AUD_SAI1_RXFS 0x06000041>,
> + <IMX8QM_SAI1_TXD_AUD_SAI1_TXD 0x06000061>,
> + <IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0x06000041>,
> + <IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0 0x0600004d>;
> + };
> +
> + pinctrl_usbotg1: usbotg1grp {
> + fsl,pins = <IMX8QM_USB_SS3_TC2_CONN_USB_OTG1_OC 0x00000021>,
> + <IMX8QM_USB_SS3_TC0_CONN_USB_OTG1_PWR 0x00000021>;
> + };
> +
> + pinctrl_usbhub: usbhubgrp {
> + fsl,pins = <IMX8QM_ESAI1_SCKT_LSIO_GPIO2_IO07 0x00000021>;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
> + fsl,pins = <IMX8QM_USDHC1_DATA6_LSIO_GPIO5_IO21 0x00000021>,
> + <IMX8QM_USDHC1_DATA7_LSIO_GPIO5_IO22 0x00000021>;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041>,
> + <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021>,
> + <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021>,
> + <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021>,
> + <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021>,
> + <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021>,
> + <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> + fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041>,
> + <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021>,
> + <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021>,
> + <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021>,
> + <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021>,
> + <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021>,
> + <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> + fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041>,
> + <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021>,
> + <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021>,
> + <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021>,
> + <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021>,
> + <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021>,
> + <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8qm-tqma8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-tqma8qm.dtsi
> new file mode 100644
> index 0000000000000..d94605c999915
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qm-tqma8qm.dtsi
> @@ -0,0 +1,318 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright (c) 2019-2026 TQ-Systems GmbH <linux at ew.tq-group.com>,
> + * D-82229 Seefeld, Germany.
> + * Author: Alexander Stein
> + */
> +
> +#include <dt-bindings/firmware/imx/rsrc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +#include "imx8qm.dtsi"
> +
> +/ {
> + model = "TQ-Systems i.MX8QM TQMa8QM";
> + compatible = "tq,imx8qm-tqma8qm", "fsl,imx8qm";
> +
> + memory at 80000000 {
> + device_type = "memory";
> + /*
> + * DRAM base addr, size : 1024 MiB DRAM
> + * should be corrected by bootloader
> + */
> + reg = <0x00000000 0x80000000 0 0x40000000>;
> + };
> +
> + reg_tqma8x_v3v3: regulator-tqma8x-v3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "V_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + /* SW7 controlled by SCU */
> + reg_1v8_io1: regulator-v1v8-io1 {
> + compatible = "regulator-fixed";
> + regulator-name = "V_1V8_IO1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + /* LDO4 controlled by SCU */
> + reg_3v3_emmc: regulator-v3v3-emmc {
> + compatible = "regulator-fixed";
> + regulator-name = "V_3V3_EMMC";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +};
> +
> +&acm {
> + status = "okay";
> +};
> +
> +&adc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0>;
> + vref-supply = <®_vref_v1v8>;
> + status = "okay";
> +};
> +
> +/* TQMa8QM only uses industrial grade, reduce trip points accordingly */
> +&cpu_alert0 {
> + temperature = <95000>;
> +};
> +
> +&cpu_crit0 {
> + temperature = <100000>;
> +};
> +
> +&cpu_alert1 {
> + temperature = <95000>;
> +};
> +
> +&cpu_crit1 {
> + temperature = <100000>;
> +};
> +
> +&gpu_alert0 {
> + temperature = <95000>;
> +};
> +
> +&gpu_crit0 {
> + temperature = <100000>;
> +};
> +
> +&gpu_alert1 {
> + temperature = <95000>;
> +};
> +
> +&gpu_crit1 {
> + temperature = <100000>;
> +};
> +
> +&drc_alert0 {
> + temperature = <95000>;
> +};
> +
> +&drc_crit0 {
> + temperature = <100000>;
> +};
> +/* end of temperature grade adjustments */
> +
> +&flexspi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi0>;
> + status = "okay";
> +
> + flash0: flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <66000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + vcc-supply = <®_1v8_io1>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_lpi2c1>;
> + pinctrl-1 = <&pinctrl_lpi2c1gpio>;
> + scl-gpios = <&lsio_gpio0 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&lsio_gpio0 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + se97: temperature-sensor at 1b {
> + compatible = "nxp,se97b", "jedec,jc-42.4-temp";
> + reg = <0x1b>;
> + };
> +
> + pcf85063: rtc at 51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + quartz-load-femtofarads = <7000>;
> + };
> +
> + at24c02: eeprom at 53 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + read-only;
> + vcc-supply = <®_tqma8x_v3v3>;
> + };
> +
> + m24c64: eeprom at 57 {
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + pagesize = <32>;
> + vcc-supply = <®_tqma8x_v3v3>;
> + };
> +};
> +
> +&mu_m0 {
> + status = "okay";
> +};
> +
> +&mu1_m0 {
> + status = "okay";
> +};
> +
> +&mu2_m0 {
> + status = "okay";
> +};
> +
> +&thermal_zones {
> + pmic0-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <2000>;
> + thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
> +
> + trips {
> + pmic_alert0: trip0 {
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + pmic_crit0: trip1 {
> + temperature = <125000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&pmic_alert0>;
> + cooling-device =
> + <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A72_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A72_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + bus-width = <8>;
> + vmmc-supply = <®_3v3_emmc>;
> + vqmmc-supply = <®_1v8_io1>;
> + no-sd;
> + no-sdio;
> + non-removable;
> + status = "okay";
> +};
> +
> +&vpu {
> + compatible = "nxp,imx8qm-vpu";
> + status = "okay";
> +};
> +
> +&vpu_core0 {
> + memory-region = <&decoder_boot>, <&decoder_rpc>;
> + status = "okay";
> +};
> +
> +&vpu_core1 {
> + memory-region = <&encoder1_boot>, <&encoder1_rpc>;
> + status = "okay";
> +};
> +
> +&vpu_core2 {
> + memory-region = <&encoder2_boot>, <&encoder2_rpc>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_lpi2c1: lpi2c1grp {
> + fsl,pins = <IMX8QM_GPT0_CAPTURE_DMA_I2C1_SDA 0x0600004d>,
> + <IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004d>;
> + };
> +
> + pinctrl_lpi2c1gpio: lpi2c1gpiogrp {
> + fsl,pins = <IMX8QM_GPT0_CAPTURE_LSIO_GPIO0_IO15 0x0600004d>,
> + <IMX8QM_GPT0_CLK_LSIO_GPIO0_IO14 0x0600004d>;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041>,
> + <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021>,
> + <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021>,
> + <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021>,
> + <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021>,
> + <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021>,
> + <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021>,
> + <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021>,
> + <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021>,
> + <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021>,
> + <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041>,
> + <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021>;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
> + fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040>,
> + <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021>,
> + <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021>,
> + <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021>,
> + <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021>,
> + <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021>,
> + <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021>,
> + <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021>,
> + <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021>,
> + <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021>,
> + <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041>,
> + <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021>;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
> + fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000040>,
> + <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021>,
> + <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021>,
> + <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021>,
> + <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021>,
> + <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021>,
> + <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021>,
> + <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021>,
> + <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021>,
> + <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021>,
> + <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041>,
> + <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021>;
> + };
> +
> + pinctrl_flexspi0: flexspi0grp {
> + fsl,pins = <IMX8QM_QSPI0A_DATA0_LSIO_QSPI0A_DATA0 0x0000004d>,
> + <IMX8QM_QSPI0A_DATA1_LSIO_QSPI0A_DATA1 0x0000004d>,
> + <IMX8QM_QSPI0A_DATA2_LSIO_QSPI0A_DATA2 0x0000004d>,
> + <IMX8QM_QSPI0A_DATA3_LSIO_QSPI0A_DATA3 0x0000004d>,
> + <IMX8QM_QSPI0A_DQS_LSIO_QSPI0A_DQS 0x0000004d>,
> + <IMX8QM_QSPI0A_SS0_B_LSIO_QSPI0A_SS0_B 0x0000004d>,
> + <IMX8QM_QSPI0A_SS1_B_LSIO_QSPI0A_SS1_B 0x0000004d>,
> + <IMX8QM_QSPI0A_SCLK_LSIO_QSPI0A_SCLK 0x0000004d>,
> + <IMX8QM_QSPI0B_SCLK_LSIO_QSPI0B_SCLK 0x0000004d>,
> + <IMX8QM_QSPI0B_DATA0_LSIO_QSPI0B_DATA0 0x0000004d>,
> + <IMX8QM_QSPI0B_DATA1_LSIO_QSPI0B_DATA1 0x0000004d>,
> + <IMX8QM_QSPI0B_DATA2_LSIO_QSPI0B_DATA2 0x0000004d>,
> + <IMX8QM_QSPI0B_DATA3_LSIO_QSPI0B_DATA3 0x0000004d>,
> + <IMX8QM_QSPI0B_DQS_LSIO_QSPI0B_DQS 0x0000004d>,
> + <IMX8QM_QSPI0B_SS0_B_LSIO_QSPI0B_SS0_B 0x0000004d>,
> + <IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x0000004d>;
> + };
> +};
> --
> 2.43.0
>
More information about the linux-arm-kernel
mailing list