[PATCH V2] arm64: dts: imx8mp-evk: Disable PCIe bus in the default dts

[Sherry Sun]

> Subject: Re: [PATCH V2] arm64: dts: imx8mp-evk: Disable PCIe bus in the
> default dts
> 
> On Fri, Mar 20, 2026 at 05:03:53PM +0800, Sherry Sun wrote:
> > Disable the PCIe bus in the default device tree to avoid shared
> > regulator conflicts between SDIO and PCIe buses. The non-deterministic
> > probe order between these two buses can break the PCIe initialization
> > sequence, causing PCIe devices to fail detection intermittently.
> >
> > On i.MX8MP EVK board, the M.2 connector is physically wired to both
> > USDHC1 and PCIe0, however the out-of-box module is SDIO IW612 WiFi, so
> > enable the SDIO WiFi in the default imx8mp-evk.dts, and provide a
> > separate device tree overlay (imx8mp-evk-pcie.dtso) to enable the PCIe
> > bus when needed.
> >
> > Signed-off-by: Sherry Sun <sherry.sun at nxp.com>
> > ---
> > Chanegs in V2:
> > 1. Improve the commit message to clarify SDIO WiFi is the out-of-box
> module on
> >    i.MX8MP EVK board.
> > ---
> >  arch/arm64/boot/dts/freescale/Makefile        |  4 +++-
> >  .../boot/dts/freescale/imx8mp-evk-pcie.dtso   | 19 +++++++++++++++++++
> >  arch/arm64/boot/dts/freescale/imx8mp-evk.dts  |  4 ++--
> >  3 files changed, 24 insertions(+), 3 deletions(-)  create mode 100644
> > arch/arm64/boot/dts/freescale/imx8mp-evk-pcie.dtso
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile
> > b/arch/arm64/boot/dts/freescale/Makefile
> > index 780682258e71..107ca270ef32 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -333,12 +333,14 @@ imx8mp-evk-lvds0-imx-lvds-hdmi-dtbs +=
> > imx8mp-evk.dtb imx8mp-evk-lvds0-imx-lvds-
> > imx8mp-evk-lvds1-imx-dlvds-hdmi-channel0-dtbs += imx8mp-evk.dtb
> > imx8mp-evk-lvds1-imx-dlvds-hdmi-channel0.dtbo
> >  imx8mp-evk-lvds1-imx-lvds-hdmi-dtbs += imx8mp-evk.dtb
> > imx8mp-evk-lvds1-imx-lvds-hdmi.dtbo
> >  imx8mp-evk-mx8-dlvds-lcd1-dtbs += imx8mp-evk.dtb
> > imx8mp-evk-mx8-dlvds-lcd1.dtbo -imx8mp-evk-pcie-ep-dtbs +=
> > imx8mp-evk.dtb imx-pcie0-ep.dtbo
> > +imx8mp-evk-pcie-dtbs := imx8mp-evk.dtb imx8mp-evk-pcie.dtbo
> > +imx8mp-evk-pcie-ep-dtbs += imx8mp-evk-pcie.dtb imx-pcie0-ep.dtbo
> >  dtb-$(CONFIG_ARCH_MXC) +=
> > imx8mp-evk-lvds0-imx-dlvds-hdmi-channel0.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk-lvds0-imx-lvds-hdmi.dtb
> >  dtb-$(CONFIG_ARCH_MXC) +=
> > imx8mp-evk-lvds1-imx-dlvds-hdmi-channel0.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk-lvds1-imx-lvds-hdmi.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk-mx8-dlvds-lcd1.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk-pcie.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk-pcie-ep.dtb
> >
> >  imx8mp-tqma8mpql-mba8mpxl-lvds-tm070jvhg33-dtbs +=
> > imx8mp-tqma8mpql-mba8mpxl.dtb
> > imx8mp-tqma8mpql-mba8mpxl-lvds-tm070jvhg33.dtbo
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk-pcie.dtso
> > b/arch/arm64/boot/dts/freescale/imx8mp-evk-pcie.dtso
> > new file mode 100644
> > index 000000000000..4f6546d442bf
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk-pcie.dtso
> > @@ -0,0 +1,19 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright 2026 NXP
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +&pcie_phy {
> > +	status = "okay";
> > +};
> > +
> > +&pcie0 {
> > +	status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > +	status = "disabled";
> > +};
> 
> Please use one overlay for both imx95 and imx8mp to enable pcie0 and
> disable usdhc1.

Hi Frank,

imx8mp has a specific pcie_phy, I disabled it in the default imx8mp-evk.dts
and enabled it in xxx-pcie.dtso, if we use one overlay for both imx95 and imx8mp,
is it acceptable that we need to keep the 8mp pcie_phy enabled even in non-PCIe
usage scenarios?

Best Regards
Sherry

> 
> Frank
> 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > index aedc09937716..f09335e6388d 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
> > @@ -763,7 +763,7 @@ &pcie_phy {
> >  	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
> >  	clocks = <&pcie0_refclk>;
> >  	clock-names = "ref";
> > -	status = "okay";
> > +	status = "disabled";
> >  };
> >
> >  &pcie0 {
> > @@ -773,7 +773,7 @@ &pcie0 {
> >  	vpcie-supply = <&reg_pcie0>;
> >  	vpcie3v3aux-supply = <&reg_pcie0>;
> >  	supports-clkreq;
> > -	status = "okay";
> > +	status = "disabled";
> >  };
> >
> >  &pcie0_ep {
> > --
> > 2.37.1
> >