[PATCH 1/4] arm64: dts: imx952: Add audio device nodes

[Daniel Baluta]

On 3/12/26 08:54, Shengjiu Wang wrote:
>> On 3/12/26 05:49, Shengjiu Wang wrote:
>>> Add audio device nodes, include SAI, MICFIL, ASRC, Audio Mixer.
>>>
>>> Signed-off-by: Shengjiu Wang <shengjiu.wang at nxp.com>
>>> ---
>>>  arch/arm64/boot/dts/freescale/imx952.dtsi | 199 ++++++++++++++++++++++
>>>  1 file changed, 199 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/freescale/imx952.dtsi b/arch/arm64/boot/dts/freescale/imx952.dtsi
>>> index 0f86b5626cdd..5787c12e788f 100644
>>> --- a/arch/arm64/boot/dts/freescale/imx952.dtsi
>>> +++ b/arch/arm64/boot/dts/freescale/imx952.dtsi
>>> @@ -823,6 +823,156 @@ usdhc3: mmc at 42c40000 {
>>>                       };
>>>               };
>>>
>>> +             aips5: bus at 43000000 {
>>> +                     compatible = "fsl,aips-bus", "simple-bus";
>>> +                     reg = <0 0x43000000 0 0x800000>;
>>> +                     #address-cells = <1>;
>>> +                     #size-cells = <1>;
>>> +                     ranges = <0x43000000 0x0 0x43000000 0x800000>;
>>> +
>>> +                     asrc1: asrc at 43000000 {
>>> +                             compatible = "fsl,imx952-asrc";
>>> +                             reg = <0x43000000 0x10000>;
>>> +                             interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
>>> +                             clocks = <&scmi_clk IMX952_CLK_BUSWAKEUP>,
>>> +                                      <&scmi_clk IMX952_CLK_BUSWAKEUP>,
>>> +                                      <&scmi_clk IMX952_CLK_ASRC1>,
>>> +                                      <&scmi_clk IMX952_CLK_ASRC2>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>,
>>> +                                      <&clk_dummy>;
>>> +                             clock-names = "mem", "ipg",
>>> +                                           "asrck_0", "asrck_1", "asrck_2", "asrck_3",
>>> +                                           "asrck_4", "asrck_5", "asrck_6", "asrck_7",
>>> +                                           "asrck_8", "asrck_9", "asrck_a", "asrck_b",
>>> +                                           "asrck_c", "asrck_d", "asrck_e", "asrck_f",
>>> +                                           "spba";
>>> +                             dmas = <&edma2 97 0 0>, <&edma2 98 0 0>, <&edma2 99 0 0>,
>>> +                                    <&edma2 100 0 1>, <&edma2 101 0 1>, <&edma2 102 0 1>;
>> For consistency we should use symbolic macros for directions like you did below.
>> Use FSL_EDMA_RX for rx direction and also introduce FSL_EDMA_TX for tx direction.
> Yes, should use FSL_EDMA_RX.
>
> But introduce FSL_EDMA_TX, it should be zero,  FSL_EDMA_TX = 0.
> is it necessary to add it in include/dt-bindings/dma/fsl-edma.h?

I would say yes. For consistency with FSL_EDMA_RX and also for

code readability.

A user doesn't know that 0 means TX. 

We could go on and merge this patch as is right now, no problems. And come back later

with a set of cleanup patches that do this for all dtses.