[PATCH 1/4] arm64: dts: imx952: Add audio device nodes

[Daniel Baluta]

On 3/12/26 05:49, Shengjiu Wang wrote:
> Add audio device nodes, include SAI, MICFIL, ASRC, Audio Mixer.
>
> Signed-off-by: Shengjiu Wang <shengjiu.wang at nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/imx952.dtsi | 199 ++++++++++++++++++++++
>  1 file changed, 199 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx952.dtsi b/arch/arm64/boot/dts/freescale/imx952.dtsi
> index 0f86b5626cdd..5787c12e788f 100644
> --- a/arch/arm64/boot/dts/freescale/imx952.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx952.dtsi
> @@ -823,6 +823,156 @@ usdhc3: mmc at 42c40000 {
>  			};
>  		};
>  
> +		aips5: bus at 43000000 {
> +			compatible = "fsl,aips-bus", "simple-bus";
> +			reg = <0 0x43000000 0 0x800000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x43000000 0x0 0x43000000 0x800000>;
> +
> +			asrc1: asrc at 43000000 {
> +				compatible = "fsl,imx952-asrc";
> +				reg = <0x43000000 0x10000>;
> +				interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&scmi_clk IMX952_CLK_BUSWAKEUP>,
> +					 <&scmi_clk IMX952_CLK_BUSWAKEUP>,
> +					 <&scmi_clk IMX952_CLK_ASRC1>,
> +					 <&scmi_clk IMX952_CLK_ASRC2>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>,
> +					 <&clk_dummy>;
> +				clock-names = "mem", "ipg",
> +					      "asrck_0", "asrck_1", "asrck_2", "asrck_3",
> +					      "asrck_4", "asrck_5", "asrck_6", "asrck_7",
> +					      "asrck_8", "asrck_9", "asrck_a", "asrck_b",
> +					      "asrck_c", "asrck_d", "asrck_e", "asrck_f",
> +					      "spba";
> +				dmas = <&edma2 97 0 0>, <&edma2 98 0 0>, <&edma2 99 0 0>,
> +				       <&edma2 100 0 1>, <&edma2 101 0 1>, <&edma2 102 0 1>;

For consistency we should use symbolic macros for directions like you did below.
Use FSL_EDMA_RX for rx direction and also introduce FSL_EDMA_TX for tx direction.


> +				dma-names = "rxa", "rxb", "rxc",
> +					    "txa", "txb", "txc";
> +				#sound-dai-cells = <0>;
> +				fsl,asrc-rate  = <8000>;
> +				fsl,asrc-width = <16>;
> +				status = "disabled";
> +			};


[...]

> +			sai3: sai at 433e0000 {
> +				compatible = "fsl,imx952-sai", "fsl,imx95-sai";
> +				reg = <0x433e0000 0x10000>;
> +				interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&scmi_clk IMX952_CLK_BUSWAKEUP>, <&clk_dummy>,
> +					 <&scmi_clk IMX952_CLK_SAI3>, <&clk_dummy>,
> +					 <&clk_dummy>;
> +				clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
> +				dmas = <&edma2 61 0 FSL_EDMA_RX>, <&edma2 60 0 0>;
As I said we should introduce FSL_EDMA_TX and this will read as:

dmas = <&edma2 61 0 FSL_EDMA_RX>, <&edma2 60 0 FSL_EDMA_TX>;

Otherwise, looks good to me.