[PATCH 3/3] arm64: dts: amlogic: t7: Add clock controller nodes

[Ronald Claveau]

On 3/5/26 8:43 AM, Jian Hu wrote:
> Add the required clock controller nodes for Amlogic T7 SoC family:
> - SCMI clock controller
> - PLL clock controller
> - Peripheral clock controller
> 
> Signed-off-by: Jian Hu <jian.hu at amlogic.com>
> ---
>  arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi | 125 ++++++++++++++++++++
>  1 file changed, 125 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> index 6510068bcff9..6ea1b583b13d 100644
> --- a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> @@ -6,6 +6,9 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/power/amlogic,t7-pwrc.h>
>  #include "amlogic-t7-reset.h"
> +#include <dt-bindings/clock/amlogic,t7-scmi.h>
> +#include <dt-bindings/clock/amlogic,t7-pll-clkc.h>
> +#include <dt-bindings/clock/amlogic,t7-peripherals-clkc.h>
>  
>  / {
>  	interrupt-parent = <&gic>;
> @@ -201,6 +204,33 @@ pwrc: power-controller {
>  		};
>  	};
>  
> +	sram at f7042000 {
> +		compatible = "mmio-sram";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0x0 0xf7042000 0x100>;
> +
> +		scmi_shmem: sram at 0 {
> +			compatible = "arm,scmi-shmem";
> +			reg = <0x0 0x100>;
> +		};
> +	};
> +
> +	firmware {
> +		scmi: scmi {
> +			compatible = "arm,scmi-smc";
> +			arm,smc-id = <0x820000c1>;
> +			shmem = <&scmi_shmem>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			scmi_clk: protocol at 14 {
> +				reg = <0x14>;
> +				#clock-cells = <1>;
> +			};
> +		};
> +	};
> +
>  	soc {
>  		compatible = "simple-bus";
>  		#address-cells = <2>;
> @@ -224,6 +254,42 @@ apb4: bus at fe000000 {
>  			#size-cells = <2>;
>  			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
>  
> +			clkc_periphs:clock-controller at 0 {
> +				compatible = "amlogic,t7-peripherals-clkc";
> +				reg = <0x0 0x0 0x0 0x1c8>;
> +				#clock-cells = <1>;
> +				clocks = <&xtal>,
> +					 <&scmi_clk CLKID_SYS_CLK>,
> +					 <&scmi_clk CLKID_FIXED_PLL>,
> +					 <&scmi_clk CLKID_FCLK_DIV2>,
> +					 <&scmi_clk CLKID_FCLK_DIV2P5>,
> +					 <&scmi_clk CLKID_FCLK_DIV3>,
> +					 <&scmi_clk CLKID_FCLK_DIV4>,
> +					 <&scmi_clk CLKID_FCLK_DIV5>,
> +					 <&scmi_clk CLKID_FCLK_DIV7>,
> +					 <&hifi CLKID_HIFI_PLL>,
> +					 <&gp0 CLKID_GP0_PLL>,
> +					 <&gp1 CLKID_GP1_PLL>,
> +					 <&mpll CLKID_MPLL1>,
> +					 <&mpll CLKID_MPLL2>,
> +					 <&mpll CLKID_MPLL3>;
> +				clock-names = "xtal",
> +					      "sys",
> +					      "fix",
> +					      "fdiv2",
> +					      "fdiv2p5",
> +					      "fdiv3",
> +					      "fdiv4",
> +					      "fdiv5",
> +					      "fdiv7",
> +					      "hifi",
> +					      "gp0",
> +					      "gp1",
> +					      "mpll1",
> +					      "mpll2",
> +					      "mpll3";
> +			};
> +
>  			reset: reset-controller at 2000 {
>  				compatible = "amlogic,t7-reset";
>  				reg = <0x0 0x2000 0x0 0x98>;
> @@ -234,6 +300,7 @@ watchdog at 2100 {
>  				compatible = "amlogic,t7-wdt";
>  				reg = <0x0 0x2100 0x0 0x10>;
>  				clocks = <&xtal>;
> +
>  			};

Did you forget to add something here for watchdog ?
If not I think you can remove that blank line.

>  
>  			periphs_pinctrl: pinctrl at 4000 {
> @@ -269,6 +336,64 @@ uart_a: serial at 78000 {
>  				status = "disabled";
>  			};
>  
> +			gp0:clock-controller at 8080 {
> +				compatible = "amlogic,t7-gp0-pll";
> +				reg = <0x0 0x8080 0x0 0x20>;
> +				clocks = <&scmi_clk CLKID_TOP_PLL_OSC>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			gp1:clock-controller at 80c0 {
> +				compatible = "amlogic,t7-gp1-pll";
> +				reg = <0x0 0x80c0 0x0 0x14>;
> +				clocks = <&scmi_clk CLKID_TOP_PLL_OSC>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			hifi:clock-controller at 8100 {
> +				compatible = "amlogic,t7-hifi-pll";
> +				reg = <0x0 0x8100 0x0 0x20>;
> +				clocks = <&scmi_clk CLKID_TOP_PLL_OSC>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			pcie:clock-controller at 8140 {
> +				compatible = "amlogic,t7-pcie-pll";
> +				reg = <0x0 0x8140 0x0 0x1c>;
> +				clocks = <&scmi_clk CLKID_PCIE_OSC>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			mpll:clock-controller at 8180 {
> +				compatible = "amlogic,t7-mpll";
> +				reg = <0x0 0x8180 0x0 0x28>;
> +				clocks = <&scmi_clk CLKID_FIXED_PLL_DCO>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			hdmi:clock-controller at 81c0 {
> +				compatible = "amlogic,t7-hdmi-pll";
> +				reg = <0x0 0x81c0 0x0 0x20>;
> +				clocks = <&scmi_clk CLKID_HDMI_PLL_OSC>;
> +				clock-names = "in0";
> +				#clock-cells = <1>;
> +			};
> +
> +			mclk:clock-controller at 8300 {
> +				compatible = "amlogic,t7-mclk-pll";
> +				reg = <0x0 0x8300 0x0 0x18>;
> +				clocks = <&scmi_clk CLKID_MCLK_PLL_OSC>,
> +					 <&xtal>,
> +					 <&scmi_clk CLKID_FCLK_50M>;
> +				clock-names = "in0", "in1", "in2";
> +				#clock-cells = <1>;
> +			};
> +
>  			sec_ao: ao-secure at 10220 {
>  				compatible = "amlogic,t7-ao-secure",
>  					     "amlogic,meson-gx-ao-secure",


-- 
Best regards,
Ronald