[PATCH v1 2/4] arm64: dts: ti: var-som-am62p: update audio codec configuration

[Stefano Radaelli]

Update the WM8904 audio codec configuration on the VAR-SOM-AM62P.

Set the audio reference clock rate to 12 MHz and add the codec DRC, GPIO
and DMIC configuration required by the board.

Signed-off-by: Stefano Radaelli <stefano.r at variscite.com>
---
 arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi | 21 ++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi
index be19cbaffc4b..9440891339b3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi
@@ -152,7 +152,7 @@ simple-audio-card,cpu {
 };
 
 &audio_refclk1 {
-	assigned-clock-rates = <100000000>;
+	assigned-clock-rates = <12000000>;
 };
 
 &cpsw3g {
@@ -204,6 +204,25 @@ wm8904: audio-codec at 1a {
 		DBVDD-supply = <&reg_3v3>;
 		DCVDD-supply = <&reg_1v8>;
 		MICVDD-supply = <&reg_1v8>;
+		wlf,drc-cfg-names = "default", "peaklimiter", "tradition",
+				    "soft", "music";
+		/*
+		 * Config registers per name, respectively:
+		 * KNEE_IP = 0,   KNEE_OP = 0,     HI_COMP = 1,   LO_COMP = 1
+		 * KNEE_IP = -24, KNEE_OP = -6,    HI_COMP = 1/4, LO_COMP = 1
+		 * KNEE_IP = -42, KNEE_OP = -3,    HI_COMP = 0,   LO_COMP = 1
+		 * KNEE_IP = -45, KNEE_OP = -9,    HI_COMP = 1/8, LO_COMP = 1
+		 * KNEE_IP = -30, KNEE_OP = -10.5, HI_COMP = 1/4, LO_COMP = 1
+		 */
+		wlf,drc-cfg-regs = /bits/ 16 <0x01af 0x3248 0x0000 0x0000>,
+				   /bits/ 16 <0x04af 0x324b 0x0010 0x0408>,
+				   /bits/ 16 <0x04af 0x324b 0x0028 0x0704>,
+				   /bits/ 16 <0x04af 0x324b 0x0018 0x078c>,
+				   /bits/ 16 <0x04af 0x324b 0x0010 0x050e>;
+		/* GPIO1 = DMIC_CLK, don't touch others */
+		wlf,gpio-cfg = <0x0018>, <0xffff>, <0xffff>, <0xffff>;
+		/* DMIC is connected to IN1L */
+		wlf,in1l-as-dmicdat1;
 	};
 };
 
-- 
2.47.3