[PATCH v3 3/7] net: wwan: t9xx: Add control DMA interface

[Andrew Lunn]

> diff --git a/drivers/net/wwan/t9xx/pcie/mtk_cldma.c b/drivers/net/wwan/t9xx/pcie/mtk_cldma.c

> +static inline void mtk_cldma_clr_bd_dsc(struct cldma_drv_info *drv_info,
> +					struct bd_dsc *bd_dsc_pool, int nr_bds)

No inline functions in C files. Please let the compiler decide.

> +static int mtk_cldma_reload_rx_skb(struct mtk_md_dev *mdev, struct rxq *rxq,
> +				   struct rx_req *req)
> +{
> +	struct sk_buff *tail = NULL;
> +	struct bd_dsc *bd_dsc;
> +	int nr_bds;
> +	int i, ret;
> +
> +	nr_bds = rxq->nr_bds;
> +
> +	for (i = 0; i < nr_bds; i++) {
> +		bd_dsc = req->bd_dsc_pool + i;
> +		bd_dsc->skb = __dev_alloc_skb(req->frag_size, GFP_KERNEL);
> +		if (!bd_dsc->skb) {
> +			dev_warn((mdev)->dev, "Failed to alloc SKB\n");

You might want to rate limit this, and the other similar messages in
the data path, otherwise it could be a DOS.

> +u32 mtk_cldma_stop_queue(struct cldma_drv_info *drv_info, enum mtk_tx_rx dir, u32 qno)
> +{
> +	u32 val = (qno == ALLQ) ? qno : BIT(qno);
> +	struct cldma_hw_regs *hw_regs;
> +	unsigned int active;
> +	int cnt = 0;
> +	int base;
> +	u32 addr;
> +
> +	hw_regs = drv_info->hw_regs;
> +	base = drv_info->base_addr;
> +
> +	if (dir == DIR_TX)
> +		addr = base + hw_regs->reg_cldma_ul_stop_cmd;
> +	else
> +		addr = base + hw_regs->reg_cldma_so_stop_cmd;
> +
> +	mtk_pci_write32(drv_info->mdev, addr, val);
> +
> +	do {
> +		active = drv_info->drv_ops->cldma_queue_status(drv_info, dir, qno);
> +		if (active == LINK_ERROR_VAL || !active)
> +			break;
> +		usleep_range(WAIT_QUEUE_STOP, 2 * WAIT_QUEUE_STOP);
> +	} while (++cnt < 10);

Please use one of the helpers from iopoll.h. Any loops waiting for an
event to happen should use those macros, since the open code
implementation is often wrong.

> +static int mtk_ctrl_trb_srv_init(struct mtk_ctrl_trans *trans)
> +{
> +	struct srv_que *srv_que;
> +	struct trb_srv *srv;
> +	int i, j;
> +	int ret;
> +
> +	for (i = 0; i < trans->trb_srv_num; i++) {
> +		srv = devm_kzalloc(trans->mdev->dev, sizeof(*srv), GFP_KERNEL);
> +		if (!srv) {
> +			ret = -ENOMEM;
> +			goto err_free_srv;
> +		}
> +
> +		srv->trans = trans;
> +		srv->srv_id = i;
> +		trans->trb_srv[i] = srv;
> +
> +		init_waitqueue_head(&srv->trb_waitq);
> +		for (j = 0; j < NR_CLDMA; j++)
> +			INIT_LIST_HEAD(&srv->srv_q_list[j]);
> +	}
> +
> +	for (i = 0; i < NR_CLDMA; i++)
> +		for (j = 0; j < HW_QUE_NUM; j++) {
> +			if (trans->srv_cfg[i][j] < 0 ||
> +			    trans->srv_cfg[i][j] >= trans->trb_srv_num)
> +				trans->srv_cfg[i][j] = 0;
> +			srv_que = devm_kzalloc(trans->mdev->dev, sizeof(*srv_que), GFP_KERNEL);
> +			if (!srv_que) {
> +				ret = -ENOMEM;
> +				goto err_free_srv_que;
> +			}
> +			srv_que->hif_id = i;
> +			srv_que->qno = j;
> +			list_add_tail(&srv_que->list,
> +				      &trans->trb_srv[trans->srv_cfg[i][j]]->srv_q_list[i]);
> +		}
> +
> +	for (i = 0; i < trans->trb_srv_num; i++) {
> +		trans->trb_srv[i]->trb_thread = kthread_run(mtk_ctrl_trb_thread, trans->trb_srv[i],
> +							    "mtk_trb_srv%d_%s", i,
> +							    trans->mdev->dev_str);
> +		if (IS_ERR(trans->trb_srv[i]->trb_thread)) {
> +			ret = PTR_ERR(trans->trb_srv[i]->trb_thread);
> +			trans->trb_srv[i]->trb_thread = NULL;
> +			goto err_stop_kthread;
> +		}
> +	}
> +
> +	return 0;
> +err_stop_kthread:
> +	while (--i >= 0)
> +		kthread_stop(trans->trb_srv[i]->trb_thread);
> +err_free_srv_que:
> +	for (i = 0; i < trans->trb_srv_num; i++) {
> +		for (j = 0; j < NR_CLDMA; j++) {
> +			struct srv_que *next_srv_que;
> +
> +			list_for_each_entry_safe(srv_que, next_srv_que,
> +						 &trans->trb_srv[i]->srv_q_list[j], list) {
> +				list_del(&srv_que->list);
> +				devm_kfree(trans->mdev->dev, srv_que);

It is unusual to see devm_kfree(). Why is it needed?

> +static unsigned int ctrl_port_chl_mtu;

Is this a global variable? Why is it not part of priv?

> +module_param(ctrl_port_chl_mtu, uint, 0644);
> +MODULE_PARM_DESC(ctrl_port_chl_mtu, "This is used to config the ctrl port mtu!\n");

Ah. No modules parameters please. If this is an MTU, why not use the
normal networking interfaces to set the MTU?

	Andrew