[PATCH 7/8] arm64: dts: imx8qm-mek: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun at nxp.com>

The i.MX8QM-MEK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe a Root Port and
LPUART1 nodes through graph port/endpoint.

The M.2 Key E connector is powered by a 3.3V fixed regulator
(reg_3v3) on board.

Signed-off-by: Sherry Sun <sherry.sun at nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 58 +++++++++++++++-----
 1 file changed, 43 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 5e725ad8aef9..4c02592cfe14 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -32,6 +32,39 @@ memory at 80000000 {
 		reg = <0x00000000 0x80000000 0 0x40000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		pinctrl-0 = <&pinctrl_pciea_reg>;
+		pinctrl-names = "default";
+		vpcie3v3-supply = <&reg_3v3>;
+		w-disable1-gpios = <&lsio_gpio1 13 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint at 0 {
+					reg = <0>;
+					remote-endpoint = <&pciea_port0_ep>;
+				};
+			};
+
+			port at 3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint at 0 {
+					reg = <0>;
+					remote-endpoint = <&lpuart1_ep>;
+				};
+			};
+		};
+	};
+
 	xtal24m: clock-xtal24m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -320,17 +353,6 @@ reg_can2_stby: regulator-can2-stby {
 		vin-supply = <&reg_can2_en>;
 	};
 
-	reg_pciea: regulator-pcie {
-		compatible = "regulator-fixed";
-		pinctrl-0 = <&pinctrl_pciea_reg>;
-		pinctrl-names = "default";
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "mpcie_3v3";
-		gpio = <&lsio_gpio1 13 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_usb_otg1_vbus: regulator-usbotg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -718,8 +740,10 @@ &lpuart1 {
 	pinctrl-0 = <&pinctrl_lpuart1>;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		lpuart1_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
@@ -818,8 +842,12 @@ &pciea {
 
 &pciea_port0 {
 	reset-gpios = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pciea>;
-	vpcie3v3aux-supply = <&reg_pciea>;
+
+	port {
+		pciea_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &pcieb {
-- 
2.50.1