[PATCH v2 1/5] arm64: dts: st: reorder ommanager node in stm32mp257f-ev1.dts

[Amelie Delaunay]

In the ST board DTS files, the &label entries must be ordered
alphanumerically.
The nodes became misordered when &ommanager and &lptimer3 were added
simultaneously. After that, &ltdc and &lvds used the &lptimers position
as a reference.

Move ommanager at the right place to avoid future misordering.

Signed-off-by: Amelie Delaunay <amelie.delaunay at foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp257f-ev1.dts | 56 +++++++++++++++---------------
 1 file changed, 28 insertions(+), 28 deletions(-)

diff --git a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
index 14e033f365e3..f044331b8b55 100644
--- a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
+++ b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
@@ -307,34 +307,6 @@ &i2c8 {
 	/delete-property/dma-names;
 };
 
-&ommanager {
-	memory-region = <&mm_ospi1>;
-	memory-region-names = "ospi1";
-	pinctrl-0 = <&ospi_port1_clk_pins_a
-		     &ospi_port1_io03_pins_a
-		     &ospi_port1_cs0_pins_a>;
-	pinctrl-1 = <&ospi_port1_clk_sleep_pins_a
-		     &ospi_port1_io03_sleep_pins_a
-		     &ospi_port1_cs0_sleep_pins_a>;
-	pinctrl-names = "default", "sleep";
-	status = "okay";
-
-	spi at 0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		memory-region = <&mm_ospi1>;
-		status = "okay";
-
-		flash0: flash at 0 {
-			compatible = "jedec,spi-nor";
-			reg = <0>;
-			spi-rx-bus-width = <4>;
-			spi-tx-bus-width = <4>;
-			spi-max-frequency = <50000000>;
-		};
-	};
-};
-
 /* use LPTIMER with tick broadcast for suspend mode */
 &lptimer3 {
 	status = "okay";
@@ -374,6 +346,34 @@ lvds_out0: endpoint {
 	};
 };
 
+&ommanager {
+	memory-region = <&mm_ospi1>;
+	memory-region-names = "ospi1";
+	pinctrl-0 = <&ospi_port1_clk_pins_a
+		     &ospi_port1_io03_pins_a
+		     &ospi_port1_cs0_pins_a>;
+	pinctrl-1 = <&ospi_port1_clk_sleep_pins_a
+		     &ospi_port1_io03_sleep_pins_a
+		     &ospi_port1_cs0_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	spi at 0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		memory-region = <&mm_ospi1>;
+		status = "okay";
+
+		flash0: flash at 0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-rx-bus-width = <4>;
+			spi-tx-bus-width = <4>;
+			spi-max-frequency = <50000000>;
+		};
+	};
+};
+
 &pcie_ep {
 	pinctrl-names = "default", "init";
 	pinctrl-0 = <&pcie_pins_a>;

-- 
2.43.0