[PATCH v5 09/10] iio: dac: add mcf54415 DAC

[Jonathan Cameron]

On Wed, 10 Jun 2026 22:35:14 +0200
Angelo Dureghello <adureghello at baylibre.com> wrote:

> From: Angelo Dureghello <adureghello at baylibre.com>
> 
> Add basic version of mcf54415 DAC driver. DAC is embedded in the SoC and
> DAC configuration registers are mapped in the internal IO address space.
> 
> The DAC accepts a 12-bit digital signal and creates a monotonic 12-bit
> analog output varying from DAC_VREFL to DAC_VREFH. The DAC module
> consists of a conversion unit, an output amplifier, and the associated
> digital control blocks. Default register values for DAC_VREFL and DAC_VREFH
> are respectively 0 and 0xfff, left untouched in this initial version.
> 
> This initial version of the driver is minimalistic, "output raw" only, to
> be extended in the future. DMA and external sync are disabled, default mode
> is high speed, default format is right-justified 12-bit on 16-bit word.
> 
> Signed-off-by: Angelo Dureghello <adureghello at baylibre.com>
I'm lazy so didn't check earlier versions but assume the two bits
of feedback from Sashiko are false positives:
https://sashiko.dev/#/patchset/20260610-wip-stmark2-dac-v5-0-b76b83366d5c%40baylibre.com

The one about clock underflow if resume fails, and then devm cleanup happens later
is a bit nasty.

I did a bit of digging and maybe it is better to just leave the clock on?
The status dev.power.is_suspended is set to false whether or not resume succeeded
and I believe a following suspend will not take into account that resume failed.

I'm not set up to poke the combinations but it might be worth trying that.
+CC common clk people who may immediately know what the right answer is.

Otherwise just a few minor style comments inline.

Thanks,

Jonathan

> ---
> Changes in v2:
> - remove tests from commit message, moved to patch 0
> - remove additional blank lines
> - remove dead code and unused definitions
> - use regmap
> - add limit check on raw write
> - non functional style fixes
> - add COMPILE_TEST to Kconfig
> Changes in v3:
> - add comments where needed
> - code style changes
> - remove unneeded variables
> - use regmap_set_bits where possible
> - remove macro not needed to define a single channel
> - set up regmap to big_endian accesses for next patches that will come,
>   that will adjust ColdFire readx/writex as standard LE (links in 0/x).
> - add return value check on regmap calls
> - sashiko: remove unneeded .io_port from regmap init.
> - sashiko: add select REGMAP_MMIO in Kconfig
> Changes in v4:
> - remove unused includes
> - sashiko: return "ret" as regmap_read ret value in case of error
> - sashiko: using u32 as regmap_read value
> - use local variable in mcf54415_dac_init() for better readability
> - sashiko: check mcf54415_dac_init return value also in resume()
> Changes in v5:
> - commit syntax fixes
> - minor code style fixes
> - use include <linux/type.h>
> - removed unneeded cast
> - disable clock in case of DAC init error
> - use unsigned int for regmap_read and GENMASK for masking 12 bits
> - add id table to match "mcfdac" platform device name
> ---
>  drivers/iio/dac/Kconfig        |  11 +++
>  drivers/iio/dac/Makefile       |   1 +
>  drivers/iio/dac/mcf54415_dac.c | 216 +++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 228 insertions(+)
> 
> diff --git a/drivers/iio/dac/Kconfig b/drivers/iio/dac/Kconfig
> index cd4870b65415..b1a578076188 100644
> --- a/drivers/iio/dac/Kconfig
> +++ b/drivers/iio/dac/Kconfig
> @@ -516,6 +516,17 @@ config MAX5821
>  	  Say yes here to build support for Maxim MAX5821
>  	  10 bits DAC.
>  
> +config MCF54415_DAC
> +	tristate "NXP MCF54415 DAC driver"
> +	depends on M5441x || COMPILE_TEST
> +	select REGMAP_MMIO
> +	help
> +	  Say yes here to build support for NXP MCF54415
> +	  12bit DAC.

Rewrap this.

> +
> +	  To compile this driver as a module, choose M here: the module
> +	  will be called mcf54415_dac.
> +
> diff --git a/drivers/iio/dac/mcf54415_dac.c b/drivers/iio/dac/mcf54415_dac.c
> new file mode 100644
> index 000000000000..f223aa80aabf
> --- /dev/null
> +++ b/drivers/iio/dac/mcf54415_dac.c

> +
> +static int mcf54415_dac_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct iio_dev *indio_dev;
> +	struct mcf54415_dac *info;
> +	void __iomem *regs;
> +	int ret;
> +
> +	indio_dev = devm_iio_device_alloc(dev, sizeof(*info));
> +	if (!indio_dev)
> +		return -ENOMEM;
> +
> +	info = iio_priv(indio_dev);
> +
> +	regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(regs))
> +		return dev_err_probe(dev, PTR_ERR(regs), "failed to get io regs\n");
> +
> +	info->map = devm_regmap_init_mmio(dev, regs, &mcf54415_dac_regmap_config);
> +	if (IS_ERR(info->map))
> +		return PTR_ERR(info->map);
> +
> +	info->clk = devm_clk_get_enabled(dev, "dac");
> +	if (IS_ERR(info->clk))
> +		return dev_err_probe(dev, PTR_ERR(info->clk), "failed getting clock\n");
> +
> +	platform_set_drvdata(pdev, indio_dev);
> +
> +	indio_dev->name = "mcf54415";
> +	indio_dev->info = &mcf54415_dac_iio_info;
> +	indio_dev->modes = INDIO_DIRECT_MODE;
> +	indio_dev->channels = &mcf54415_dac_iio_channel;
> +	indio_dev->num_channels = 1;
> +
> +	ret = mcf54415_dac_init(info);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_add_action_or_reset(dev, mcf54415_dac_exit, info);
> +	if (ret)
> +		return ret;
> +
> +	return devm_iio_device_register(dev, indio_dev);
> +}
> +
> +static int mcf54415_dac_suspend(struct device *dev)
> +{
> +	struct mcf54415_dac *info = iio_priv(dev_get_drvdata(dev));
> +
> +	mcf54415_dac_exit(info);
> +	clk_disable_unprepare(info->clk);
> +
> +	return 0;
> +}
> +
> +static int mcf54415_dac_resume(struct device *dev)
> +{
> +	struct mcf54415_dac *info = iio_priv(dev_get_drvdata(dev));
> +	int ret;
> +
> +	ret = clk_prepare_enable(info->clk);
> +	if (ret)
> +		return ret;
> +
> +	ret = mcf54415_dac_init(info);
> +	if (ret) {
> +		dev_err(dev, "could not resume device\n");
> +		clk_disable_unprepare(info->clk);
> +	}
> +
> +	return ret;
> +}
> +
> +static DEFINE_SIMPLE_DEV_PM_OPS(mcf54415_dac_pm_ops,
> +				mcf54415_dac_suspend, mcf54415_dac_resume);
> +
> +static const struct platform_device_id mcf54415_dac_ids[] = {
> +	{ .name = "mcfdac", .driver_data = 0 },

Don't set .driver_data if you aren't using it.  Given very strong
preference for always using a pointer for that (rather than a numeric
value) this line will change if you ever add support for more devices
anyway, so no value in having that there now.

> +	{ }, /* sentinel */
	{ }

No comma and I don't see value in the sentinel marking given that is
fairly obvious.

> +};
> +
No blank line here.  Intent is to keep the macro and the function closely
coupled.

> +MODULE_DEVICE_TABLE(platform, mcf54415_dac_ids);