[PATCH v3 0/9] ARM: dts: aspeed: anacapa: restructure devicetree for development-phase

[Colin Huang]

Andrew Jeffery <andrew at codeconstruct.com.au> 於 2026年6月10日週三 下午9:04寫道：
>
> On Tue, 2026-06-02 at 21:24 +0800, Colin Huang via B4 Relay wrote:
> > This series refactors the Anacapa BMC devicetree layout to better support
> > development-phase hardware revisions (EVT1/EVT2/DVT) while keeping a platform
> > entrypoint.
> >
> > Signed-off-by: Colin Huang <u8813345 at gmail.com>
> > ---
> > Changes in v3:
> > - Restructure the EVT2 devicetree to inherit from the EVT1 devicetree, making it incremental rather than standalone.
> > - Add the DVT devicetree, inheriting from the EVT2 devicetree.
> > - Enable MCTP and FRU support for the NIC.
> > - Align PDB fan GPIO numbering.
> > - Add an EEPROM device node for the NFC adaptor board.
> > - Add an additional EEPROM device node for the SCM.
> > - Add shunt resistor values for HSC monitors
> > - Link to v2: https://lore.kernel.org/r/20260409-anacapa-devlop-phase-devicetree-v2-0-68f328671653@gmail.com
> >
>
> So just to check, the changes in patches 5-8 inclusive are applicable
> to all of EVT1, EVT2 and DVT (given the way you've structured the
> includes)?

Yes, these patch apply to all development phase.

>
> > Changes in v2:
> > - Fix dtbs_check fail.
> >   Validated by following command:
> >     make dt_binding_check DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml
> >     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa.dtb
> >     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt1.dtb
> >     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt2.dtb
> > - Link to v1: https://lore.kernel.org/r/20260407-anacapa-devlop-phase-devicetree-v1-0-97b96367cac3@gmail.com
> >
> > ---
> > Andy Chung (1):
> >       ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC
> >
> > Carl Lee (1):
> >       ARM: dts: aspeed: anacapa: Add eeprom device node for NFC adaptor board
> >
> > Colin Huang (5):
> >       dt-bindings: arm: aspeed: add Anacapa EVT1 EVT2 DVT board
> >       ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it
> >       ARM: dts: aspeed: anacapa: add EVT2 devicetree inheriting EVT1
> >       ARM: dts: aspeed: anacapa: add DVT devicetree inheriting EVT2
> >       ARM: dts: aspeed: anacapa: add additional EEPROM node for SCM
>
> If you need to respin this series for some reason, can you please
> capitalise the first word of the short description (the bit after the
> last ':') for the commits above and the one below?
>

Got it.  Capitalise the first word.of the short description.

> >
> > Peter Shen (1):
> >       ARM: dts: aspeed: anacapa: evt2: add shunt resistor values for HSC monitors
> >
> > Rex Fu (1):
> >       ARM: dts: aspeed: anacapa: Align PDB fan GPIO numbering
> >
> >  .../devicetree/bindings/arm/aspeed/aspeed.yaml     |    3 +
> >  .../dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts |  178 +++
> >  .../aspeed/aspeed-bmc-facebook-anacapa-evt1.dts    | 1179 ++++++++++++++++++++
> >  .../aspeed/aspeed-bmc-facebook-anacapa-evt2.dts    |  228 ++++
> >  .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     | 1077 +-----------------
> >  5 files changed, 1589 insertions(+), 1076 deletions(-)
> > ---
> > base-commit: 7ca1caf017d34396397b19fb4de9ecef256f4acc
> > change-id: 20260407-anacapa-devlop-phase-devicetree-4101d3f312c0
> >
> > Best regards,
>
> Andrew