[PATCH v3 13/14] arm64: dts: imx8mp-var-som-symphony: add second Ethernet port

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r at variscite.com>

Add support for the second Ethernet interface available on the Symphony
carrier board.

Enable the FEC controller, add the MaxLinear MXL86110 Gigabit Ethernet
PHY on the MDIO bus, describe its reset and power configuration, and add
the required RGMII pinctrl settings.

Signed-off-by: Stefano Radaelli <stefano.r at variscite.com>
---
v2->v3:
 - Add FEC controller and MaxLinear MXL86110 PHY support

 .../dts/freescale/imx8mp-var-som-symphony.dts | 60 +++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
index 6b2aaf6bae07..f4926ce0aec7 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-var-som-symphony.dts
@@ -66,6 +66,17 @@ pcie0_refclk: pcie0-refclk {
 		clock-frequency = <100000000>;
 	};
 
+	reg_fec_phy: regulator-fec-phy {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-enable-ramp-delay = <20000>;
+		gpio = <&pca9534 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "VSD_3V3";
@@ -106,6 +117,38 @@ &ecspi2 {
 	status = "okay";
 };
 
+&eqos {
+	mdio {
+		ethphy1: ethernet-phy at 5 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <5>;
+			reset-gpios = <&pca9534 5 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <20000>;
+			vddio-supply = <&vddio1>;
+
+			vddio1: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	/*
+	 * The required RGMII TX and RX 2ns delays are implemented directly
+	 * in hardware via passive delay elements on the SOM PCB.
+	 * No delay configuration is needed in software via PHY driver.
+	 */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_fec_phy>;
+	status = "okay";
+};
+
 &flexcan2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan2>;
@@ -363,6 +406,23 @@ MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13				0x12
 		>;
 	};
 
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0				0x90
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1				0x90
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2				0x90
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3				0x90
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC				0x90
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL			0x90
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0				0x00
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1				0x00
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2				0x00
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3				0x00
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL			0x00
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC				0x00
+		>;
+	};
+
 	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_UART3_RXD__CAN2_TX					0x154
-- 
2.47.3