[PATCH v2 2/2] arm64: dts: rockchip: fix PCIe regulator name on NanoPC-T6

[Sebastian Reichel]

Hi,

On Fri, May 29, 2026 at 05:31:25PM +0200, Ricardo Pardini via B4 Relay wrote:
> From: Ricardo Pardini <ricardo at pardini.net>
> 
> The GPIO-switched 3v3 regulator on the NanoPC-T6 is labeled
> vcc3v3_pcie2x1l0, but it is wired to and consumed by &pcie2x1l1, and
> its enable is the pcie_m2_1_pwren pin - i.e. it powers the M.2 slot on
> pcie2x1l1, not pcie2x1l0. The two soldered RTL8125 NICs on pcie2x1l0
> and pcie2x1l2 instead share the always-on vcc_3v3_pcie20 rail, so
> nothing actually uses an "l0" switched supply.
> 
> Rename the label, node name and regulator-name to vcc3v3_pcie2x1l1 so
> they match the controller the rail actually supplies.
> 
> Signed-off-by: Ricardo Pardini <ricardo at pardini.net>
> ---

You should use the regulator name from the schematics. I had a quick
look and https://wiki.friendlyelec.com/wiki/images/9/97/NanoPC-T6_2301_SCH.PDF
describes the GPIO as PCIE_M2_1_PWREN as you mention in your commit
message. That GPIO controls a regulator for the power net "VDD_MPCIE_3.3V".
So that's the expected name :)

Greetings,

-- Sebastian

>  arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
> index 04c4479f08170..7d314df3f947b 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi
> @@ -203,13 +203,13 @@ vbus5v0_usb: regulator-vbus5v0-usb {
>  		vin-supply = <&vcc5v0_sys>;
>  	};
>  
> -	vcc3v3_pcie2x1l0: regulator-vcc3v3-pcie2x1l0 {
> +	vcc3v3_pcie2x1l1: regulator-vcc3v3-pcie2x1l1 {
>  		compatible = "regulator-fixed";
>  		enable-active-high;
>  		gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pcie_m2_1_pwren>;
> -		regulator-name = "vcc3v3_pcie2x1l0";
> +		regulator-name = "vcc3v3_pcie2x1l1";
>  		regulator-min-microvolt = <3300000>;
>  		regulator-max-microvolt = <3300000>;
>  		vin-supply = <&vcc5v0_sys>;
> @@ -655,7 +655,7 @@ rtl_eth0: ethernet at 0,0 {
>  
>  &pcie2x1l1 {
>  	reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> -	vpcie3v3-supply = <&vcc3v3_pcie2x1l0>;
> +	vpcie3v3-supply = <&vcc3v3_pcie2x1l1>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pcie2_1_rst>;
>  	status = "okay";
> 
> -- 
> 2.54.0
> 
> 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20260601/7034734b/attachment.sig>