[PATCH v2 07/18] arm64: dts: ti: k3-j721e: Add overlay for fusion application daughter board

[Yemike Abhilash Chandra]

Hi Udit,
Thanks for the review.

On 27/07/26 10:59, Kumar, Udit wrote:
> Thanks for patch
> 
> On 7/13/2026 5:04 PM, Yemike Abhilash Chandra wrote:
>> From: Vaishnav Achath <vaishnav.a at ti.com>
>>
>> Fusion application daughter board [1] can be used to connect multiple
>> FPDLink-III based sensors to TI EVMs. The board has two DS90UB960
>> deserializers, each of which aggregates input from up to 4x FPDLink-III
>> sensors. Up to 8x sensors can simultaneously stream over the two CSI RX
>> ports on J721E.
> J721E to same of board, please
> 
>>
>> [1]: https://svtronics.com/product/fusion-application-daughter-board-evm577pfusion-v1-0/?srsltid=AfmBOooMsRAd5ibFOGJaKbjsC3j9-loTPK2wWqsqPq2Adj55g1nPluxX
>>
>> Signed-off-by: Vaishnav Achath <vaishnav.a at ti.com>
>> Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra at ti.com>
>> ---
>> Changelog:
>> Changes in v2:
>> - Add missing bus-type property in csi2_phy0 endpoint for cdns_csi2rx0 (sashiko)
>> - Fix minor DTS styling and whitespace inconsistencies in port definitions (sashiko)
>> - Remove unused gpio.h header (sashiko)
>>
>>   arch/arm64/boot/dts/ti/Makefile               |   4 +
>> [..]
>> +		deserializer_0_ports: ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			port at 0 {
>> +				reg = <0>;
>> +				status = "disabled";
>> +			};
>> +
>> +			port at 1 {
>> +				reg = <1>;
>> +				status = "disabled";
>> +			};
>> +
>> +			port at 2 {
>> +				reg = <2>;
>> +				status = "disabled";
>> +			};
>> +
>> +			port at 3 {
>> +				reg = <3>;
>> +				status = "disabled";
>> +			};
>> +
>> +			/* CSI-2 TX */
>> +			port at 4 {
>> +				reg = <4>;
>> +				ds90ub960_0_csi_out: endpoint {
>> +					data-lanes = <1 2 3 4>;
>> +					clock-lanes = <0>;
>> +					link-frequencies = /bits/ 64 <800000000>;
>> +					remote-endpoint = <&csi2_phy0>;
>> +				};
>> +			};
>> +
>> +			port at 5 {
>> +				reg = <5>;
>> +				status = "disabled";
>> +			};
> 
> Little confused here on port number,
> I am wondering, why 5 ports are defined.
> 
> as per DS90UB960, one single part can have 4 input (from sensors)
> and 2 port output (towards SOC) page 5 from [0].
> 
> 

The DS90UB960 has 4 input ports (RX) and 2 output ports (TX).

Hence we define input ports starting from port 0 till port 3.
Port 4 and 5 correspond to the two output ports.

So the ports definition here include both input and output ports
of the DS90UB960.

Thanks and Regards,
Yemike Abhilash Chandra

> 
> https://www.ti.com/lit/ds/symlink/ds90ub960-q1.pdf
> 
> 
>> +		};
>> +
>> [..]